https://wiki.jlab.org/ciswiki/api.php?action=feedcontributions&user=Gcroke&feedformat=atomCiswikidb - User contributions [en]2024-03-28T18:19:12ZUser contributionsMediaWiki 1.35.7https://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24558200kV High Voltage Power Supply & Controls2021-05-07T11:22:31Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
;Power Supply Settings<br />
<br />
Terminal pairs 1-2, 3-4, and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation in our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies. The 'Local / IEEE-488' switch on the rear of the unit should be set to IEEE-488 (GPIB) for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
;Controller Settings<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
[[File:CO-HV hookup.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]<br />
<br />
;EPICS Control<br />
[[File:Wien control screen.png]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Wien_control_screen.png&diff=24557File:Wien control screen.png2021-05-07T11:21:26Z<p>Gcroke: </p>
<hr />
<div></div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24556200kV High Voltage Power Supply & Controls2021-05-07T11:17:56Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
;Power Supply Settings<br />
<br />
Terminal pairs 1-2, 3-4, and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation in our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies. The 'Local / IEEE-488' switch on the rear of the unit should be set to IEEE-488 (GPIB) for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
;Controller Settings<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
[[File:CO-HV hookup.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24555200kV High Voltage Power Supply & Controls2021-05-07T11:16:51Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
;Power Supply Settings<br />
<br />
Terminal pairs 1-2, 3-4, and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation in our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies. The 'Local / IEEE-488' switch on the rear of the unit should be set to IEEE-488 (GPIB) for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
;Controller Settings<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24554200kV High Voltage Power Supply & Controls2021-05-07T11:15:41Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
;Power Supply Settings<br />
<br />
Terminals 1-2, 3-4 and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation in our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies. The 'Local / IEEE-488' switch on the rear of the unit should be set to IEEE-488 (GPIB) for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
;Controller Settings<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24553200kV High Voltage Power Supply & Controls2021-05-07T11:11:35Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
;Power Supply Settings<br />
<br />
Terminals 1-2, 3-4 and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation of our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
;Controller Settings<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24552200kV High Voltage Power Supply & Controls2021-05-07T11:10:04Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
Terminals 1-2, 3-4 and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation of our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies.<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24551200kV High Voltage Power Supply & Controls2021-05-07T11:09:20Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
Terminals 1-2, 3-4 and 7-8 on the rear of the Matsusada power supplies should be jumpered for correct operation of our application. 1-2 is to allow remote HV enabling (or rather a switch-based disabling, which we don't use). 7-8 allows for remote operation of the supplies.<br />
[[File:Power supply jumpers.jpg]]<br />
[[File:Remote operation jumper.jpg]]<br />
<br />
DIP switches on the rear of the CO-HV controllers need to be set correctly. Switches 1-5 define the unit address. We use address 1 for the positive supply of each Wien, address 2 for the negative supply. Switch 8 defines the 'upper connection' of the optical link, essentially the system master. Set switch 8 on the unit that is addressed 1.<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
<br />
Here is the pinout of the control cable that connects the CO-HV controller to the power supply:<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24550200kV High Voltage Power Supply & Controls2021-05-07T11:00:29Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
<br />
[[File:Power supply jumpers.jpg]]<br />
[[File:Remote operation jumper.jpg]]<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.jpg]]<br />
[[File:Switches.png]]<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=24549200kV High Voltage Power Supply & Controls2021-05-07T10:58:43Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies and Controller<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS output voltage accuracy.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
<br />
<br />
[[File:Power supply jumpers.png]]<br />
[[File:Remote operation jumper.png]]<br />
[[File:CO-HV hookup.png]]<br />
[[File:Controller switches.png]]<br />
[[File:Switches.png]]<br />
[[File:Control cable.png]]<br />
<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]<br />
[[File:Wien HV rack ISB March 2021.jpg]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Control_cable.png&diff=24548File:Control cable.png2021-05-07T10:53:06Z<p>Gcroke: Pinout of controller - power supply cable</p>
<hr />
<div>Pinout of controller - power supply cable</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:CO-HV_hookup.png&diff=24547File:CO-HV hookup.png2021-05-07T10:52:08Z<p>Gcroke: Explanation of RS-232 - CO-HV controller - power supply communcation connections from manual.</p>
<hr />
<div>Explanation of RS-232 - CO-HV controller - power supply communcation connections from manual.</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Switches.png&diff=24546File:Switches.png2021-05-07T10:51:13Z<p>Gcroke: Explanation of CO-HV DIP switches from manual</p>
<hr />
<div>Explanation of CO-HV DIP switches from manual</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Remote_operation_jumper.jpg&diff=24545File:Remote operation jumper.jpg2021-05-07T10:46:49Z<p>Gcroke: Explanation of 7-8 jumper setting from manual</p>
<hr />
<div>Explanation of 7-8 jumper setting from manual</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Power_supply_jumpers.jpg&diff=24544File:Power supply jumpers.jpg2021-05-07T10:44:43Z<p>Gcroke: Correct installation of Matsusada power supplies jumpers.</p>
<hr />
<div>Correct installation of Matsusada power supplies jumpers.</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Controller_switches.jpg&diff=24543File:Controller switches.jpg2021-05-07T10:44:00Z<p>Gcroke: Correct settings for CO-HV DIP switches</p>
<hr />
<div>Correct settings for CO-HV DIP switches</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_Wien_filter_-_FINAL&diff=22170200kV Wien filter - FINAL2020-11-19T14:03:03Z<p>Gcroke: Add link to wien signals file</p>
<hr />
<div>'''Wien filter refurbishing for 200 keV beam: +/- 20kV per electrode plate and 20A/75V coils'''<br />
* [[Media:Wien_signals.xlsx]] - list and description of EPICS PVs for new Wien filters<br />
* [[Media:Voltage readouts cal test plan Rev01.pptx]]<br />
* [https://wiki.jlab.org/ciswiki/index.php/October_28,_2020_-_Wien_HV_controls_update_meeting Wien HV controls meeting 10/28/20]<br />
* [https://wiki.jlab.org/ciswiki/index.php/October_27,_2020_-_Wien_magnetic_field_mapping_and_characterization_meeting Wien magnetic field mapping and characterization meeting 10/27/20]<br />
* [https://logbooks.jlab.org/entry/3855679 Wien filter 200 keV upgrade tasks update 10/26/20->H Wien filter chamber fixed magnet now fits, fixtures assembled]<br />
* [https://logbooks.jlab.org/entry/3855302 Wien filter 200 keV upgrade tasks update 10/21/20->H Wien filter chamber back to the shop for lug skimming]<br />
* [https://logbooks.jlab.org/entry/3855204 Wien filter 200 keV upgrade tasks update 10/20/20->V Wien filter ready for field mapping]<br />
* [[Media:CEBAF Wiens rebuild schedule Nov 13 2020.png]]<br />
<br />
<br />
* Wien Calculations: [[media:WienSpinControl.pdf]] [[media:WienSpinControl.pptx]]<br />
* Vertical Wien Field Map: [[media:VWien_FieldMap.pdf]] [[media:VWien_FieldMap.pptx]] [[media:NewVWienFieldMap.xlsx]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Wien_signals.xlsx&diff=22112File:Wien signals.xlsx2020-11-18T17:57:18Z<p>Gcroke: PV listing and descriptions for new Wien controls</p>
<hr />
<div>PV listing and descriptions for new Wien controls</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=200kV_High_Voltage_Power_Supply_%26_Controls&diff=20830200kV High Voltage Power Supply & Controls2020-08-06T14:52:09Z<p>Gcroke: </p>
<hr />
<div>This page contains information about the high voltage power supply controls used at CEBAF and UITF.<br />
<br />
;Power Supplies<br />
:+/- 30 kV HVPS [https://www.matsusada.com/pdf/af_ae.pdf] AE-30P1-LG (+30kV) and AE-30N1-LG (-30kV) [[File:Matsusada AE series spec sheet.pdf]]<br />
:[[Media:Matsusada PS quote JeffersonLabAE09062017-1.pdf]]<br />
:Matsusda HV power supplies operations manual [[Media:Matsusada AE 30kV PS series manual.pdf]]<br />
:[[Media:CO series communication controller.pdf]]<br />
:[[Media:CO series REV 0.4.pdf]]<br />
:[[Media:cable quote.pdf]]<br />
:[[Media:Matsusada_comm_troubleshooting.txt]]<br />
;HV Switcher chassis & controls<br />
:[[Media:wien_systems_block_diagram_uitf.pdf]]<br />
:[[Media:HV switch chassis schematic.pdf]]<br />
:[[Media:HV switch I0177M1.pdf]]<br />
:[[Media:HV switch I0178F1.pdf]]<br />
:[[Media:HV switch I0179F1.pdf]]<br />
:[[Media:HV switch I0180F1.pdf]]<br />
:[[Media:g71c.pdf]]</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=File:Matsusada_comm_troubleshooting.txt&diff=20829File:Matsusada comm troubleshooting.txt2020-08-06T14:45:55Z<p>Gcroke: Notes on troubleshooting comm problem with Matsusada HV power supplies</p>
<hr />
<div>Notes on troubleshooting comm problem with Matsusada HV power supplies</div>Gcrokehttps://wiki.jlab.org/ciswiki/index.php?title=Matsusada_Wein_Filter_Power_supplies_2018&diff=19357Matsusada Wein Filter Power supplies 20182020-02-19T15:32:41Z<p>Gcroke: </p>
<hr />
<div>This page describes the implementation of the Matsusada 0-30kV power supplies for driving the <br />
Wein filter high voltage plates.<br />
<br />
We attempt to purchase systems completely off-the-shelf as much as possible for this application. <br />
It may look like something of a rats nest of serial, fiber optic, and interface cables, <br />
but that is how it comes from Matsusada. The serial cable from the Digiport server does not go<br />
directly to the power supplies. Instead it goes to a serial to optical converter box.<br />
The reason behind converting to optical is so the DAQ system can be galvanically isolated from <br />
the power supplies. This ensures that any noise on the digital side is not transferred to <br />
the analog outputs, and any noise that might be created on the analog outputs will not affect<br />
the digital side.<br />
<br />
The optical-GPIB units communicate independently of the power supplies, not just a pass-through. They continue communicating, even sending status information when the supplies are off/disconnected. The remote/local status relates to the units, not the supplies.<br />
<br />
The first five DIP switch settings on each unit sets the address. Switch 8 means upstream link (first in chain). Unit 1 should set switches 1 & 8, unit 2 should set switch 2. Our setup is most like page 9 of the CO series manual.<br />
<br />
<br />
<br />
Output cable quote. Cable custom made by Dielectric Sciences [[Media:cable quote.pdf]]<br />
<br />
Power Supply Purchase Order [[Media:JeffersonLabAE09062017-1.pdf]]<br />
<br />
Matsusada specs sheet [[Media:Af_ae.pdf]] The HV power supplies are rated 30 kV, 1 mA<br />
<br />
CO series communication controller overview [[Media:CO series communication controller.pdf]]<br />
<br />
CO series manual [[Media:CO series REV 0.4.pdf]]<br />
<br />
AE series manual [[Media:AE series REV 0.0.pdf]]<br />
<br />
Wein HV system control side wiring diagram [[Media:WEIN HV SYSTEM WIRING DIAGRAM.pdf]]<br />
<br />
Wein HV system High Voltage side wiring diagram [[Media:WEIN HV switch.pdf]]<br />
<br />
GigaVac HV switch datasheet [[Media:Gigavac.pdf]]<br />
<br />
Note: dwg file of WEIN HV system wiring diagram stored at:<br />
<br />
O:\inj_group\Official Electronic Design Packages\Wein HV 2018 design package</div>Gcroke