Difference between revisions of "Gun2 Load Lock Chamber Replacement"
Jump to navigation
Jump to search
(Created page with " #Danny, what else ought I do to confirm travel, in case I get into tunnel? '''=> ???''' #Phi/Marcy, can you confirm Danny's parts list, set them aside when found? '''=> Phil,...") |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | #Danny, what else ought I do to confirm travel, in case I get into tunnel? '''=> | + | ===Joe's punchlist from 6/11:=== |
| + | #Danny, what else ought I do to confirm travel, in case I get into tunnel? '''=> didn't happen, still necessary?''' | ||
#Phi/Marcy, can you confirm Danny's parts list, set them aside when found? '''=> Phil, see parts list below''' | #Phi/Marcy, can you confirm Danny's parts list, set them aside when found? '''=> Phil, see parts list below''' | ||
| − | #Matt, do you want us to replace the UHV 2" stroke manipulator? '''=> no, we can keep the one | + | #Matt, do you want us to replace the UHV 2" stroke manipulator? '''=> no, we can keep the one Matt gave us''' |
#All, do we want larger IP tee w/ reducer to port-aligner, to improve load/bake pumping? '''=> talked to Danny, he's looking at this''' | #All, do we want larger IP tee w/ reducer to port-aligner, to improve load/bake pumping? '''=> talked to Danny, he's looking at this''' | ||
#Marcy, can you look at heating blankets for this geometry, good idea? '''=> come w/ info''' | #Marcy, can you look at heating blankets for this geometry, good idea? '''=> come w/ info''' | ||
#All, do we have spare motor to drive UHV manipulator? '''=> don't need''' | #All, do we have spare motor to drive UHV manipulator? '''=> don't need''' | ||
| − | Danny's e-mail from 6/11: | + | ===Danny's e-mail from 6/11:=== |
| − | Attached is what i've layed out for the puck dock. It will hold 3 pucks and fit in the space occupied by the existing tee. this allows us to re-use the existing suitcase manipulator. though i still have to confirm how it has adequate travel to work presently. i think a new manipulator is around 3-4k. this looks to be the least expensive way to accomplish a load lock. we can spend less on the tee weldment, but only have one or two puck capabilities. we could do without the port-aligner if we didn't want to align the puck holder under vacuum. but then the puck holder gets to be more complicated. we'll have to use studs and nuts into the valves on both sides of the tee. i understand we want to be able to install this in august, so i'll start on the purchase reqs and detail drawings. | + | Attached is what i've layed out for the puck dock: [[media:PUCKDOCKJUNE10.pdf]] |
| + | |||
| + | It will hold 3 pucks and fit in the space occupied by the existing tee. this allows us to re-use the existing suitcase manipulator. though i still have to confirm how it has adequate travel to work presently. i think a new manipulator is around 3-4k. this looks to be the least expensive way to accomplish a load lock. we can spend less on the tee weldment, but only have one or two puck capabilities. we could do without the port-aligner if we didn't want to align the puck holder under vacuum. but then the puck holder gets to be more complicated. we'll have to use studs and nuts into the valves on both sides of the tee. i understand we want to be able to install this in august, so i'll start on the purchase reqs and detail drawings. | ||
We have on hand: | We have on hand: | ||
| Line 17: | Line 20: | ||
We have to order: | We have to order: | ||
| − | -port-aligner, i think this costs about $1500 | + | -port-aligner, i think this costs about $1500 '''=> Matt says to buy (2), one for UITF''' |
-6"-2.75" CF zero length reducer? or do we have one? | -6"-2.75" CF zero length reducer? or do we have one? | ||
-two 6" CF non-rotatable flanges? or do we have them? | -two 6" CF non-rotatable flanges? or do we have them? | ||
Latest revision as of 08:15, 21 June 2019
Joe's punchlist from 6/11:
- Danny, what else ought I do to confirm travel, in case I get into tunnel? => didn't happen, still necessary?
- Phi/Marcy, can you confirm Danny's parts list, set them aside when found? => Phil, see parts list below
- Matt, do you want us to replace the UHV 2" stroke manipulator? => no, we can keep the one Matt gave us
- All, do we want larger IP tee w/ reducer to port-aligner, to improve load/bake pumping? => talked to Danny, he's looking at this
- Marcy, can you look at heating blankets for this geometry, good idea? => come w/ info
- All, do we have spare motor to drive UHV manipulator? => don't need
Danny's e-mail from 6/11:
Attached is what i've layed out for the puck dock: media:PUCKDOCKJUNE10.pdf
It will hold 3 pucks and fit in the space occupied by the existing tee. this allows us to re-use the existing suitcase manipulator. though i still have to confirm how it has adequate travel to work presently. i think a new manipulator is around 3-4k. this looks to be the least expensive way to accomplish a load lock. we can spend less on the tee weldment, but only have one or two puck capabilities. we could do without the port-aligner if we didn't want to align the puck holder under vacuum. but then the puck holder gets to be more complicated. we'll have to use studs and nuts into the valves on both sides of the tee. i understand we want to be able to install this in august, so i'll start on the purchase reqs and detail drawings.
We have on hand: -the linear manipulator for the vertical travel. -2.75 tee, i presume. -ion pump, reuse the 20l/s one on the existing tee. -4.5" window.
We have to order: -port-aligner, i think this costs about $1500 => Matt says to buy (2), one for UITF -6"-2.75" CF zero length reducer? or do we have one? -two 6" CF non-rotatable flanges? or do we have them? -6" window? or do we have one? -two 4.5" CF rotatable flanges? or do we have them? -2.5" tube? or do we have some? -4.5" CF non-rotatable? or do we have one? -reducing cross, 4" tube x 2.5" tube.
We have to fabricate: -2.75 flange with puck holder. -reducing cross weld ment