CIS Phase 1 work plans

Week 1 (Sep 21 - Sep 27) High Voltage Testing w/ PSS lock-ups

• Updated schedule media:200914_AIPINJ_Weeks_Sep_18_update.docx
• High voltage test slides media:200902_HV_Plans.pptx
• Gun and Wien tasks Media:High Voltage Work Gun2 & Wien filters.xlsx

Week 2 (Sep 28 - Oct 4) - Instrument, Magnet, LCW, Air, Laser disconnects

Fri 9/25 - Mon 9/28

• CIS Gun Jobs

Wien electrode testing – 9am!!!

Gun HVPS lockout - DONE

Gun HV cable disconnect – DONE

Remove PIG – Coordinate w/ Neil for convenient time

Shukui - Laser outrigger table as-founds, remove components

Scott - Remove yellow box

Scott - Disconnect Decarad

Monday 9/28 Tasks (updated 0915 9/28)

• Power down Wein system (Scott/Joe)
• Power down and remove DecaRad system (Scott)
• Return gun valve config to "normal" (Marcy)
• Dispose of grey mineral oil tank in coordination w/ESH&Q (Carlos/Bubba)
• PSS Kickers and associated chassis removal (SSG)
• Laser table disassembly (Shukui/Scott)

Tuesday 9/29 Tasks (updated 0930 9/29)

• (Done) Disconnect BPMs 2I01->0I02A (Pete) beginning 5a
• (Done) Disconnect aperture and cup signal cables (Pete) 5a
• Disconnect rad probes (Melvin) 8a
• Tunnel magnet disconnects (Diggs, Delk) 10a
• (Done) Removal of old chopper amps from rack (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• ODH Head Replacements (SSG)
• Document existing Wein cabling and power off PS (Scott)

Wednesday 9/30 Tasks (updated 0900 9/30)

• RF Prebuncher disconnects (Farrish) 6a
• Vacuum Component Labeling (Greenfield, Gonzales) 430a
• Magnet disconnects -- wire wrap-ups, junction box investigation (Coleman, Diggs, Delk) 10a
• Tiny magnet removals (Scott, Grames) 9a
• PSS Kicker Magnet removal (SSG) 9a
• Sample hold cables install, InjSB (Francis)
• Remaining PSS Interface chassis removal (SSG)
• Harp upgrade to PC104 (Dela Cruz)
• Moser transfers CCOC phone @1430, to reach moving forward x5089

Thursday 10/1 Tasks (updated 0830 10/1)

• Picoammeter Removal, InjSB (Francis) 5a
• Sample hold cables install, IN02B24 (Francis)
• BPM Work in IN02B2* (Francis)
• Chopper amplifier upgrade (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• Viewer+harp hardware disconnects (Norris, Dela Cruz) 6a
• Disconnecting water and air lines from apertures and cups (Adderley) 8a
• Mech Install Pre-Job Walk-Thru (Grames, Wilson) 9a

Friday 10/2 Tasks (updated 0900 10/2)

• Viewer disconnects (Norris) 6a
• BPM Work in IN02B2* (Francis)
• Chopper amplifier upgrade (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• PSS Kicker Cables tie-up (SSG)
• Survey and Alignment control measure around gun (S&A)
• Load suitcase with "bad" pucks (CIS)
• Pump-down vacuum in front of tee for next week (CIS)

Tunnel Work

Time	Mon 9/28	Tue 9/29	Wed 9/30	Thu 10/1	F 10/2
4a - 8a		I&C; 5a: Francis: BPMs, Cups, Apertures	I&C; 430a: Greenfield + Gonzales: vacuum labelling; 6a: Farrish: Prebuncher	I&C; 6a: Norris: Viewer; 6a: Dela Cruz, Harps	I&C: Norris: Viewer disconnects
8a - 10a	CIS + SSG	RadCon: rad probes	SSG: Kicker magnet removal; CIS: Tiny magnet removals	CIS; Adderley: Aperture+Cups Air/Water; Grames: Mech Install Walk-Thru	S&A: Gun
10a - 12p	CIS + SSG	DC Power	DC Power: Wire wrap-ups, junction box investigation		S&A: Gun; SSG: Kicker cable tie-up
12p - 2p	CIS + SSG	DC Power	DC Power: Wire wrap-ups, junction box investigation	DC Power	S&A: Gun
2p - 4p	CIS + SSG	DC Power	3p: Moser: Safety Warden checks		S&A: Gun
4p - ??

Other Work Occurring When Convenient

• Remove suitcase, Tunnel (CIS)
• Harp upgrade, InjSB (I&C)
• ODH Head Replacement, InjSB and Tunnel (SSG)
• PSS Chassis Removals, InjSB (SSG)

Week 3 (Oct 5 - Oct 11) - Vacuum disconnects, girder/pedestal removal, injector survey network

Monday Oct 5

• vacuum tests, disconnects, and pre-removal blank offs (CIS)
• QCM->downstream Survey and Alignment
• S&H cable work for iocinse4, InjSB (Francis)

Tuesday Oct 6

• Survey and Alignment finishing up around 0L04 (S&A)
• U-tube operations at 0L03 (Cryo)
• S&H cable work for iocinse4, InjSB (Francis)
• Stage/prepare for craning our girders (Mech Install)
• Chopper SSA upgrade -- LCW line install, InjSB (Mech Install / RF)

Wednesday Oct 7

• S&H cable work for iocinse4, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Wein PS Work, InjSB (Windham)
• VIP UHV PS Work, InjSB (Windham)
• Harp PC104 upgrade, InjSB (Dela Cruz)

Thursday Oct 8

• BPM work, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Harp PC104 upgrade, InjSB (Dela Cruz)

Wednesday Oct 7 and Thursday Oct 8 -- Mechanical Install

• Remove to test lab --
  • Laser outrigger table
  • 1st Wein girder and pedestals
  • 2nd Wein girder, apertures, and pedestals
  • Photocathode puck suitcase on cart
• Remove to Brett Lewis grey oil tank
• Penetration stone drops

Current list of Injector penetrations to be dropped: 57, 86, 108, possibly this one

Penetration drop distance e3854100:

• 34ft from floor of InjSB to floor of Inj tunnel
• 25ft from floor of InjSB to elevated Inj tunnel cable tray

Friday Oct 9

• BPM Work, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Harp PC104 upgrade, InjSB (Dela Cruz)
• Penetration stone drop -- 57, 86, 108, Tunnel (Mech Install)
  • Penetration above laser hut already opened

Week 4 (Oct 12 - Oct 18) Cable Pulls and Y-Chamber Girder Rebuild

• Laser/Y-Chamber viewer for Y-chamber girder (Marcy)
• Fiducializing Y-chamber girder (S&A)
• Laser window under vacuum evaluations (Phil/Shukui/Caryn)
• Documenting early InjSB racks (Scott)
• Cable pulls through penetrations (EES)
• Fire pipe demolition? (Facilities Contractor)
• Wein upgrade (Carlos) --
  • Finish new Wien electrodes drawing and sign-offs
  • Vacuum chambers to machine shop for mods
  • Begin creating new screens
• Injector Tunnel Photos from W 10/14

Monday Oct 12

Tunnel --

• Hooking up VIPs to new 18V PS for load testing (Marcy/Scott)
• Cable pulls through penetrations (EES)

InjSB --

• BPM Cable Pulls through Penetration 86 (Francis)
• Chopper SSA upgrade (Farrish)
• Harp to PC104 upgrade (Dela Cruz)
• Early rack documentation and space optimization (Scott)
• PSS Upgrade work (IN02BNI, B29, B30) (SSG)

Tuesday Oct 13

Tunnel --

• Cable pulls through penetrations (EES)
• Resistor box evaluation (Coleman)

InjSB --

• BPM Work, IN02B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)

Wednesday Oct 14

Tunnel --

• Cable pulls through penetrations (EES)
• Safety warden walk-through (Moser)

InjSB --

• BPM Work, IN02B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• Determining rack location for Wien magnet PSs, IN02-middle (Coleman, Grames, Moser)
• Safety warden walk-through (Moser)
• Conduit in penetration 135 (Electricians)

Thursday Oct 15

Tunnel --

• S&A Level surveys

InjSB --

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)

Friday Oct 16

Tunnel --

• Cable pulls through penetrations (EES)
• Mott cable removals (Scott/Riad, EES)

InjSB --

• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)
• IN02B26 Power Lock-Out, ~915a (DC Power)

Week 5 (Oct 19 - Oct 23) Prep for Gun to Y Vacuum Installation

Non-Tunnel Work

• Build new Y-chamber viewer => Y-built w/test screen, Laser being built.
• Use test screen + laser + S&A to verify position of first viewer => This week
• Install + align + vacuum seal (2) viewers => target this week
• Caryn will confirm but identified best ‘mushroom’ window, attach => done
• ME provide ALL points to S&A for installation (gun table, 2I stand, Y-chamber, 2 peds for Wien, 2 peds A1/A2) => ???
• Carlos' Wien-mania!

Tunnel Work

• Complete remove old keV Mott cables => done
• Complete remove old gun HV cables => done
• Jim pulls Wien PS cables? => done
• Does Wien HV cable pull start? => starting this week
• Scott will finish tie back of cables on tunnel floor to cable tray => done
• Refill 86? => no, not yet

Standing Injector Service Building Work

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)

Monday Oct 19

Tunnel --

• Cryo u-tube pulls for 0L0{2,3,4}

Tuesday Oct 20

Tunnel --

• Cable pulls and removals

InjSB --

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, IN02B22, 2p - 4p (DC Power)

Wednesday Oct 21

Tunnel --

• S&A Verify line with new control

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (SSG - single person)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• M56 Hardware Removal from IN02B22, (I&C)

Thursday Oct 22

InjSB --

• Wien Magnet PS Install, IN02B22, afternoon (DC Power)
• Early rack documentation and space optimization, IN01B{00-05}, 9a - 4p (Windham)
• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (SSG - single person)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)

Friday Oct 23

Tunnel --

• Vacuum work clean room craned in 6a - 8a (Mech Install)
• Clean room setup and prepping (Marcy)
• Gun interlock checks in preparation of removal of old HV Interlock Chassis in IN01B02 (Windham, Grames)
• Laser room work (Shukui)

InjSB --

• Early rack documentation and space optimization, IN01B{00-05}, 9a - 4p (Windham)
• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• 20A PS Install, IN02B22 (DC Power)

Inj Service Building Work

Time	Wed 10/21	Thu 10/22	Fri 10/23
5a - 9a	Dela Cruz, Norris, Francis	Dela Cruz, Norris, Francis	Dela Cruz, Norris, Francis
9a - 12p	Francis, SSG, Windham	Francis, SSG	Francis, SSG, Windham
12p - 4p	DC Power, SSG, Windham, Francis	DC Power, SSG, Windham, Francis	DC Power, SSG, Windham, Francis

Week 6 (Oct 26 - Oct 30) Remove old Y+NEG & Move Gun2 new location

Tunnel work

• Remove NEG filter from HV chamber done
• Setup mobile cleanroom over HV chamber done
• Vent Gun3 chamber to test Gun3 valve done
• Vent Gun2 chamber to test Gun2 valve done
• Remove 2I NEG beam line, remove NEG pedestal (temporarily) Wed / Thur
• Replace 10” flange + SHV connector + blank off + pump down done
• Prep Gun3 & Y-chamber for Install to remove done
• Wrap up UHV ion pump power supply power tests done
• INSTALL lift and move gun table off feet, & move Gun3 & Y-chamber back to TL-1137 Wed / Thur
• S&A may start setting/checking points (gun feet, 2I ped, Y ped, Wien ped, A1/A2 ped) Fri

Non-Tunnel Work

• Finish Y-chamber : add viewers, add laser vacuum window, add NEG towers, add gun valve
• Wien-mania! (high level schedule)

-Wien magnetic field mapping next couple weeks

-Bubba assembles the fixtures done

Thur Oct 29

Tunnel --

• Gun2 move, 5a - 8a (Mech Install)
• Removal of Gun3 and Y-chamber to Test Lab, 5a - 8a (Mech Install)
• Wien HV and control cable pulls, 9a - 1p (Dela Cruz)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 1p (Dela Cruz)
• Viewer work, IN03B07, 6a - 1p (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)

Other possible work....

• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11}, (Farrish)
• LLRF air temperature control system removal from IN01B13? (Plawski?)
• Trim Card Checks, IN02B{10+11+26} + IN04B10, (Diggs, Richardson)

TOMORROW, Friday, All Hallows' Eve Eve Mask -- join the fun by wearing masks to the 0830 toolbox meeting.

Injector Tunnel and Service Building Work

Location Time	Mon 10/26	Tue 10/27	Wed 10/28	Thu 10/29	Fri 10/30
InjSB 5a - 9a	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis
Tunnel 5a - 9a		Gun Vacuum Work		Gun2 Table Move Y-Chamber+Gun3 Removal
InjSB 9a - 12p	Francis, SSG	Francis, Windham, SSG	Francis, Windham, SSG	Dela Cruz, Norris, Francis, SSG	Francis, SSG
Tunnel 9a - 12p	Gun Vacuum Work	Gun Vacuum Work	9a CIS+MechInstall Walk-Thru open	Wien Cable Pulls	Cryo 0L02 L-tube pull S&A Point Layouts
InjSB 12p - 4p	SSG	Windham, SSG	Windham, SSG	SSG	SSG
Tunnel 12p - 4p	Gun Vacuum Work	Gun Vacuum Work 3p:Videographer Tour			S&A Point Layouts

Mon Oct 26

Tunnel --

• Gun vacuum work, 9a - 4p (CIS)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• LLRF air temperature control system removal from IN01B13? (Plawski?)

Tues Oct 27

Tunnel --

• Gun vacuum work, 9a - 3p (CIS)
• Videographer Tour, 3p+ (K. Carter + two videographers)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• CIS Rack Work, IN01B{00-05} 9a - 4p (Windham)
• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• LLRF air temperature control system removal from IN01B13? (Plawski?)

Wed Oct 28

Tunnel --

• Opportunity for cable pulls --
  • Wien HV and control cables
  • Removal of old Cat5 viewer cables
  • New viewer cables
  • Neutron detector cablesNorris (possibly) removing old Cat5 cable

• CIS + MechInstall Walk-Through of Gun Table Move, Removal of Gun3 stub and Y-chamber, 9a

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• CIS Rack Work, IN01B{00-05} 9a - 4p (Windham)
• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11}, (Farrish)
• LLRF air temperature control system removal from IN01B13? (Plawski?)
• Trim Card Checks, IN02B{10+11+26} + IN04B10, (Diggs, Richardson)

Thur Oct 29

Tunnel --

• Gun2 move, 5a - 8a (Mech Install)
• Removal of Gun3 and Y-chamber to Test Lab, 5a - 8a (Mech Install)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)

Fri Oct 30

Tunnel --

• Laying out new pedestal points? (S&A)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23}, 5a - 1p (Francis)

Week 7 (Nov 2 - Nov 6) Point Layout and Anchor Installs

Tunnel work

• INSTALL sets new foot pads, new anchor bolts if needed
• INSTALL lift and move gun table to new foot pads
• INSTALL move new y-chamber from TL-1137 to injector, and vice versa
• S&A and CIS install and align Y-chamber + NEG tube + Gun table (CL cathode/anode)
• Pump down and leak check
• Check laser align/retro : back fill N2 + test retro from GaAs + test alignment to viewer
• Iterate as needed
• End week with laser + Y + Gun + NEG aligned (pre-bake)
• Prep for new suitcase (i.e. prep work to safe photocathodes during eventual gun bake)

InjSB Work --

• PSS Upgrade, IN02B{NI, 29, 30} (Beizer)
• Wien controls work, IN01B03 (Dela Cruz)
• Viewer work, IN03B07 (Norris)
• BPM Work, IN03B{05-08, 23} (Francis)
• CIS Rack Work, IN01B{00-05} (Windham)
• 20A Wien Magnet PS Install (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• LLRF air temperature control system removal from IN01B13 (Plawski?)

Injector Tunnel and Service Building Work

Location Time	Mon 11/2	Tue 11/3 Election Day 🇺🇸	Wed 11/4	Thu 11/5	Fri 11/6
InjSB 5a - 9a	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work
Tunnel 5a - 9a	M	MechInstall?	W	R	F
InjSB 9a - 12p	PSS Upgrade BPM Work	PSS Upgrade BPM Work	PSS Upgrade BPM Work	PSS Upgrade BPM Work	PSS Upgrade BPM Work
Tunnel 9a - 12p	S&A Setting and Checking Points	T	W	R	F
InjSB 12p - 4p	PSS Upgrade	PSS Upgrade	PSS Upgrade	PSS Upgrade	PSS Upgrade
Tunnel 12p - 4p	S&A Setting and Checking Points	T	W	R	F

Penetration Work

InjSB Penetrations that are open (click for pictures): above laser hut, 58, 86, 108, 135

• 34ft from floor of InjSB to floor of Inj tunnel
• 25ft from floor of InjSB to elevated Inj tunnel cable tray

Penetration Cable Pulls/Removals --

• Tony pulling new Wien E-field HV cables
• Norris removing old Cat5 viewer cables
• Norris pulling new viewer cables
• Riad/Scott removing old Mott HV cables
• Coleman pulling new Wien B-field magnet cables
• Cole pulling new neutron detector cables (above 0L03)
• Scott pulling motor control cables for A1++

Fire System Work

Description of Task: Replacement of tunnel sprinkler piping, fire alarm control panels in B85 & B98, replacement of detection devices.

Latest construction schedule has contractor in Injector between 11/24/20 and 1/4/21.