CIS Phase 1 work plans

2020 Weeks 1 through 13

Week 1 (Sep 21 - Sep 27) High Voltage Testing w/ PSS lock-ups

• Updated schedule media:200914_AIPINJ_Weeks_Sep_18_update.docx
• High voltage test slides media:200902_HV_Plans.pptx
• Gun and Wien tasks Media:High Voltage Work Gun2 & Wien filters.xlsx

Week 2 (Sep 28 - Oct 4) - Instrument, Magnet, LCW, Air, Laser disconnects

Fri 9/25 - Mon 9/28

• CIS Gun Jobs

Wien electrode testing – 9am!!!

Gun HVPS lockout - DONE

Gun HV cable disconnect – DONE

Remove PIG – Coordinate w/ Neil for convenient time

Shukui - Laser outrigger table as-founds, remove components

Scott - Remove yellow box

Scott - Disconnect Decarad

Monday 9/28 Tasks (updated 0915 9/28)

• Power down Wein system (Scott/Joe)
• Power down and remove DecaRad system (Scott)
• Return gun valve config to "normal" (Marcy)
• Dispose of grey mineral oil tank in coordination w/ESH&Q (Carlos/Bubba)
• PSS Kickers and associated chassis removal (SSG)
• Laser table disassembly (Shukui/Scott)

Tuesday 9/29 Tasks (updated 0930 9/29)

• (Done) Disconnect BPMs 2I01->0I02A (Pete) beginning 5a
• (Done) Disconnect aperture and cup signal cables (Pete) 5a
• Disconnect rad probes (Melvin) 8a
• Tunnel magnet disconnects (Diggs, Delk) 10a
• (Done) Removal of old chopper amps from rack (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• ODH Head Replacements (SSG)
• Document existing Wein cabling and power off PS (Scott)

Wednesday 9/30 Tasks (updated 0900 9/30)

• RF Prebuncher disconnects (Farrish) 6a
• Vacuum Component Labeling (Greenfield, Gonzales) 430a
• Magnet disconnects -- wire wrap-ups, junction box investigation (Coleman, Diggs, Delk) 10a
• Tiny magnet removals (Scott, Grames) 9a
• PSS Kicker Magnet removal (SSG) 9a
• Sample hold cables install, InjSB (Francis)
• Remaining PSS Interface chassis removal (SSG)
• Harp upgrade to PC104 (Dela Cruz)
• Moser transfers CCOC phone @1430, to reach moving forward x5089

Thursday 10/1 Tasks (updated 0830 10/1)

• Picoammeter Removal, InjSB (Francis) 5a
• Sample hold cables install, IN02B24 (Francis)
• BPM Work in IN02B2* (Francis)
• Chopper amplifier upgrade (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• Viewer+harp hardware disconnects (Norris, Dela Cruz) 6a
• Disconnecting water and air lines from apertures and cups (Adderley) 8a
• Mech Install Pre-Job Walk-Thru (Grames, Wilson) 9a

Friday 10/2 Tasks (updated 0900 10/2)

• Viewer disconnects (Norris) 6a
• BPM Work in IN02B2* (Francis)
• Chopper amplifier upgrade (Farrish)
• Harp upgrade to PC104 (Dela Cruz)
• PSS Kicker Cables tie-up (SSG)
• Survey and Alignment control measure around gun (S&A)
• Load suitcase with "bad" pucks (CIS)
• Pump-down vacuum in front of tee for next week (CIS)

Tunnel Work

Time	Mon 9/28	Tue 9/29	Wed 9/30	Thu 10/1	F 10/2
4a - 8a		I&C; 5a: Francis: BPMs, Cups, Apertures	I&C; 430a: Greenfield + Gonzales: vacuum labelling; 6a: Farrish: Prebuncher	I&C; 6a: Norris: Viewer; 6a: Dela Cruz, Harps	I&C: Norris: Viewer disconnects
8a - 10a	CIS + SSG	RadCon: rad probes	SSG: Kicker magnet removal; CIS: Tiny magnet removals	CIS; Adderley: Aperture+Cups Air/Water; Grames: Mech Install Walk-Thru	S&A: Gun
10a - 12p	CIS + SSG	DC Power	DC Power: Wire wrap-ups, junction box investigation		S&A: Gun; SSG: Kicker cable tie-up
12p - 2p	CIS + SSG	DC Power	DC Power: Wire wrap-ups, junction box investigation	DC Power	S&A: Gun
2p - 4p	CIS + SSG	DC Power	3p: Moser: Safety Warden checks		S&A: Gun
4p - ??

Other Work Occurring When Convenient

• Remove suitcase, Tunnel (CIS)
• Harp upgrade, InjSB (I&C)
• ODH Head Replacement, InjSB and Tunnel (SSG)
• PSS Chassis Removals, InjSB (SSG)

Week 3 (Oct 5 - Oct 11) - Vacuum disconnects, girder/pedestal removal, injector survey network

Monday Oct 5

• vacuum tests, disconnects, and pre-removal blank offs (CIS)
• QCM->downstream Survey and Alignment
• S&H cable work for iocinse4, InjSB (Francis)

Tuesday Oct 6

• Survey and Alignment finishing up around 0L04 (S&A)
• U-tube operations at 0L03 (Cryo)
• S&H cable work for iocinse4, InjSB (Francis)
• Stage/prepare for craning our girders (Mech Install)
• Chopper SSA upgrade -- LCW line install, InjSB (Mech Install / RF)

Wednesday Oct 7

• S&H cable work for iocinse4, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Wein PS Work, InjSB (Windham)
• VIP UHV PS Work, InjSB (Windham)
• Harp PC104 upgrade, InjSB (Dela Cruz)

Thursday Oct 8

• BPM work, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Harp PC104 upgrade, InjSB (Dela Cruz)

Wednesday Oct 7 and Thursday Oct 8 -- Mechanical Install

• Remove to test lab --
  • Laser outrigger table
  • 1st Wein girder and pedestals
  • 2nd Wein girder, apertures, and pedestals
  • Photocathode puck suitcase on cart
• Remove to Brett Lewis grey oil tank
• Penetration stone drops

Current list of Injector penetrations to be dropped: 57, 86, 108, possibly this one

Penetration drop distance e3854100:

• 34ft from floor of InjSB to floor of Inj tunnel
• 25ft from floor of InjSB to elevated Inj tunnel cable tray

Friday Oct 9

• BPM Work, InjSB (Francis)
• Chopper SSA upgrade, InjSB (Farrish)
• Harp PC104 upgrade, InjSB (Dela Cruz)
• Penetration stone drop -- 57, 86, 108, Tunnel (Mech Install)
  • Penetration above laser hut already opened

Week 4 (Oct 12 - Oct 18) Cable Pulls and Y-Chamber Girder Rebuild

• Laser/Y-Chamber viewer for Y-chamber girder (Marcy)
• Fiducializing Y-chamber girder (S&A)
• Laser window under vacuum evaluations (Phil/Shukui/Caryn)
• Documenting early InjSB racks (Scott)
• Cable pulls through penetrations (EES)
• Fire pipe demolition? (Facilities Contractor)
• Wein upgrade (Carlos) --
  • Finish new Wien electrodes drawing and sign-offs
  • Vacuum chambers to machine shop for mods
  • Begin creating new screens
• Injector Tunnel Photos from W 10/14

Monday Oct 12

Tunnel --

• Hooking up VIPs to new 18V PS for load testing (Marcy/Scott)
• Cable pulls through penetrations (EES)

InjSB --

• BPM Cable Pulls through Penetration 86 (Francis)
• Chopper SSA upgrade (Farrish)
• Harp to PC104 upgrade (Dela Cruz)
• Early rack documentation and space optimization (Scott)
• PSS Upgrade work (IN02BNI, B29, B30) (SSG)

Tuesday Oct 13

Tunnel --

• Cable pulls through penetrations (EES)
• Resistor box evaluation (Coleman)

InjSB --

• BPM Work, IN02B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)

Wednesday Oct 14

Tunnel --

• Cable pulls through penetrations (EES)
• Safety warden walk-through (Moser)

InjSB --

• BPM Work, IN02B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• Determining rack location for Wien magnet PSs, IN02-middle (Coleman, Grames, Moser)
• Safety warden walk-through (Moser)
• Conduit in penetration 135 (Electricians)

Thursday Oct 15

Tunnel --

• S&A Level surveys

InjSB --

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)

Friday Oct 16

Tunnel --

• Cable pulls through penetrations (EES)
• Mott cable removals (Scott/Riad, EES)

InjSB --

• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)
• IN02B26 Power Lock-Out, ~915a (DC Power)

Week 5 (Oct 19 - Oct 23) Prep for Gun to Y Vacuum Installation

Non-Tunnel Work

• Build new Y-chamber viewer => Y-built w/test screen, Laser being built.
• Use test screen + laser + S&A to verify position of first viewer => This week
• Install + align + vacuum seal (2) viewers => target this week
• Caryn will confirm but identified best ‘mushroom’ window, attach => done
• ME provide ALL points to S&A for installation (gun table, 2I stand, Y-chamber, 2 peds for Wien, 2 peds A1/A2) => ???
• Carlos' Wien-mania!

Tunnel Work

• Complete remove old keV Mott cables => done
• Complete remove old gun HV cables => done
• Jim pulls Wien PS cables? => done
• Does Wien HV cable pull start? => starting this week
• Scott will finish tie back of cables on tunnel floor to cable tray => done
• Refill 86? => no, not yet

Standing Injector Service Building Work

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, Rack re-org, IN02B22 (DC Power)

Monday Oct 19

Tunnel --

• Cryo u-tube pulls for 0L0{2,3,4}

Tuesday Oct 20

Tunnel --

• Cable pulls and removals

InjSB --

• BPM Work, IN0{2,3}B{*} (Francis)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• Harp to PC104 upgrade, IN03B07 (Dela Cruz)
• Early rack documentation and space optimization, IN01B{02-05} (Scott)
• PSS Upgrade, IN02{BNI, B29, B30} (SSG)
• 20A PS Install, IN02B22, 2p - 4p (DC Power)

Wednesday Oct 21

Tunnel --

• S&A Verify line with new control

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (SSG - single person)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• M56 Hardware Removal from IN02B22, (I&C)

Thursday Oct 22

InjSB --

• Wien Magnet PS Install, IN02B22, afternoon (DC Power)
• Early rack documentation and space optimization, IN01B{00-05}, 9a - 4p (Windham)
• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (SSG - single person)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)

Friday Oct 23

Tunnel --

• Vacuum work clean room craned in 6a - 8a (Mech Install)
• Clean room setup and prepping (Marcy)
• Gun interlock checks in preparation of removal of old HV Interlock Chassis in IN01B02 (Windham, Grames)
• Laser room work (Shukui)

InjSB --

• Early rack documentation and space optimization, IN01B{00-05}, 9a - 4p (Windham)
• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Viewer work, IN03B07, 6a - 9a (Norris)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• 20A PS Install, IN02B22 (DC Power)

Inj Service Building Work

Time	Wed 10/21	Thu 10/22	Fri 10/23
5a - 9a	Dela Cruz, Norris, Francis	Dela Cruz, Norris, Francis	Dela Cruz, Norris, Francis
9a - 12p	Francis, SSG, Windham	Francis, SSG	Francis, SSG, Windham
12p - 4p	DC Power, SSG, Windham, Francis	DC Power, SSG, Windham, Francis	DC Power, SSG, Windham, Francis

Week 6 (Oct 26 - Oct 30) Remove old Y+NEG & Move Gun2 new location

Tunnel work

• Remove NEG filter from HV chamber ✅
• Setup mobile cleanroom over HV chamber ✅
• Vent Gun3 chamber to test Gun3 valve ✅
• Vent Gun2 chamber to test Gun2 valve ✅
• Remove 2I NEG beam line, remove NEG pedestal (temporarily) ✅
• Replace 10” flange + SHV connector + blank off + pump down ✅
• Prep Gun3 & Y-chamber for Install to remove ✅
• Wrap up UHV ion pump power supply power tests ✅
• INSTALL lift and move gun table off feet, & move Gun3 & Y-chamber back to TL-1137 ✅
• S&A may start setting/checking points (gun feet, 2I ped, Y ped, Wien ped, A1/A2 ped) ✅

Non-Tunnel Work

• Finish Y-chamber : add viewers, add laser vacuum window, add NEG towers, add gun valve on-going
• Wien-mania! (high level schedule)

-Wien magnetic field mapping next couple weeks

-Bubba assembles the fixtures ✅

Injector Tunnel and Service Building Work

Location Time	Mon 10/26	Tue 10/27	Wed 10/28	Thu 10/29	Fri 10/30
InjSB 5a - 9a	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis	Norris, Dela Cruz, Francis
Tunnel 5a - 9a		Gun Vacuum Work	Gun Vacuum Work	Gun2 Table Move Y-Chamber+Gun3 Removal
InjSB 9a - 12p	Francis, SSG	Francis, Windham, SSG	Francis, Windham, SSG	Dela Cruz, Norris, Francis, SSG	Francis, SSG
Tunnel 9a - 12p	Gun Vacuum Work	Gun Vacuum Work	9a CIS+MechInstall Walk-Thru	Wien Cable Pulls	Cryo 0L02 L-tube pull Fire pipe walk thru S&A Point Layouts
InjSB 12p - 4p	SSG	Windham, SSG	Windham, SSG Trim Rack Checks	SSG	SSG
Tunnel 12p - 4p	Gun Vacuum Work	Gun Vacuum Work 3p:Videographer Tour			S&A Point Layouts

Mon Oct 26

Tunnel --

• Gun vacuum work, 9a - 4p (CIS)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• LLRF air temperature control system removal from IN01B13? (Plawski?)

Tues Oct 27

Tunnel --

• Gun vacuum work, 9a - 3p (CIS)
• Videographer Tour, 3p+ (K. Carter + two videographers)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• CIS Rack Work, IN01B{00-05} 9a - 4p (Windham)
• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
• LLRF air temperature control system removal from IN01B13? (Plawski?)

Wed Oct 28

Tunnel --

• CIS + MechInstall Walk-Through of Gun Table Move, Removal of Gun3 stub and Y-chamber, 9a

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 9a (Dela Cruz)
• Viewer work, IN03B07, 6a - 9a (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)
• CIS Rack Work, IN01B{00-05} 9a - 4p (Windham)
• Trim Card Checks, IN02B{10+11+26} + IN04B10, 12p-1p (Richardson)

Other Possible Work....

• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11}, (Farrish)

Thur Oct 29

Tunnel --

• Gun2 move, 5a - 8a (Mech Install)
• Removal of Gun3 and Y-chamber to Test Lab, 5a - 8a (Mech Install)
• Wien HV and control cable pulls, 9a - 1p (Dela Cruz)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 1p (Dela Cruz)
• Viewer work, IN03B07, 6a - 1p (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)

Other possible work....

• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11}, (Farrish)

All Hallows' Eve Eve 👻 (Fri 10/30)

Tunnel --

• Cryo L-tube Removal from 0L02, 8a - 12p (Cryo)
• Fire pipe demo job walk-through, 12p (Grames, Suhring, Renzo)
• Point Layouts, after cryo (S&A)

InjSB --

• PSS Upgrade, IN02B{NI, 29, 30} 9a - 4p (Beizer)
• Wien controls work, IN01B03, 6a - 1p (Dela Cruz)
• Viewer work, IN03B07, 6a - 1p (Norris)
• BPM Work, IN03B{05-08, 23} 5a - 1p (Francis)

Other possible work....

• 20A Wien Magnet PS Install, IN02B22 (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11}, (Farrish)

Week 7 (Nov 2 - Nov 6)

Fire pipe removal, viewer design, modify existing pedestals, Wien filter mapping

Tunnel work

Mon/Tue

1. INSTALL crane support (move Y-girder, Gun3 chamber, anything else back to TL1137)
2. CIS take opportunity to a) cover your stuff before fire pipe demo, b) clean up cabinets, toolbox
3. EES-IC Cable Pulls, Termination, and Routing

Wed/Thu and maybe Fri

1. Fire pipe demolition

Non-Tunnel Work

• Complete Y-chamber: add viewers, add laser vacuum window, add NEG towers, add gun valve
• Wien-mania! (high level schedule) => H/V-wien magnetic field mapping

InjSB Work

• Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos) --
  • Comm chassis to digiport server
• PSS Upgrade, IN02B{NI, 29, 30} (Beizer)
• Viewer work, IN03B0{6+7} (Norris)
• BPM Work, IN03B{05-08, 23} (Francis)
• CIS Rack Work, IN01B{00-05} (Windham)

Other possible work...

• 20A Wien Magnet PS Install (Coleman)
• Chopper SSA upgrade, back of IN01B{03-11} (Farrish)

Injector Tunnel and Service Building

Location Time	Mon 11/2	Tue 11/3 Election Day 🇺🇸	Wed 11/4	Thu 11/5	Fri 11/6
InjSB 5a - 9a	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work	BPM, Viewer, Wien Work
Tunnel 5a - 9a	Wien + viewer cable pulls INSTALL Crane Outs	Wien + viewer cable pulls	Fire pipe demo	Fire pipe demo	F(riday)
InjSB 9a - 12p	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work
Tunnel 9a - 12p	Wien + viewer cable pulls	Wien + viewer cable pulls	Fire pipe demo	Fire pipe demo	F(loat)
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	M	T	Fire pipe demo	Fire pipe demo	F

Week 8 (Nov 9 - Nov 13) Beamline anchors/pedestals, Wien mapping/HV system, A1/A2 cubes, prebuncher

Tunnel work

1. Tue - S&A is queued up to set new(er) gun foot pad points
2. Tue/Wed - Shaun predicts 4 pedestals arrive, Jenord inspects them; other peds exist in tunnel - thank you Phil/Shaun!
3. Wed/Thu/Fri - Install drills and drops anchors, prepare grout form?, maybe we return gun table (Tom, best guess for the fire pipe install?)

ME work

• S&A drop revised points for table base pads. ECD 11/10. done

• 2I solenoid – done

SG print full size drill template for Neil.

Check fit of template.

• Neil – Drill holes into top of solenoid stand (existing item and is currently in place) using drill template provided by Shaun. done

• Neil drill anchor holes in floor done

HVC table base pads. done

Wien Girder Pedestals. done

Aperture Girder Pedestals. done

Details have been provided to Neil. done

• Y chamber girder

Design new v-block mounting for Y & ion pump due to angle change of Y.

Fabricate or modifications.

Non-Tunnel Work

1. Wien-mania! (high level schedule) - Wien magnet mapping, HVPS system controls (ADC/DAC), Switchbox build
2. Complete Y-chamber build : laser window + (2) viewers + NEG Tower + Valve (gun3!?)
3. A1/A2 cube assemblies - (2) for vacuum testing, (1) for magnet fit-up/testing
4. Prebuncher vacuum repair, leak check

• Did the leak check braze joint happen?
• Did a final probe port length get decided?
• Can we resolve these question, repair the probe port, clean, ready for testing by Friday?

1. Submit PR for PSS kicker

ISB Work

1. Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos) --
   • Wire HV PS
   • Install Comm chassis
2. PSS Upgrade, IN02B{NI, 29, 30} (Beizer)
3. Viewer upgrades, IN03B07 (Norris)
4. Harp upgrades, IN03B07 (Dela Cruz)
5. BPM Work, IN03B{05-08, 23} (Francis) Phase I: ✅; jump-start on Phase II ✅
6. CIS Rack Work, IN01B{00-05} (Windham)
7. Chopper SSA upgrade, back of IN01B{03-11} (Farrish)
8. First Aid Cabinet re-stocks, back wall behind IN02B22ish + bottom of access stairs, (Occ Med + vendor), date TBD

Injector Tunnel and Service Building

Location Time	Mon 11/9	Tue 11/10	Wed 11/11	Thu 11/12	Fri 11/13
InjSB 5a - 9a	BPM, Viewer, Wien Work	BPM, Viewer, Wien, Harp Work	BPM, Viewer, Wien, Harp Work	BPM, Viewer, Wien, Harp Work	Viewer, Wien, Harp Work
Tunnel 5a - 9a	Viewer Cable Pulls	T	INSTALL Pedestals, base pads, solenoid stand drilling	INSTALL work Viewer Cable Pulls	S&A Survey Pedestals
InjSB 9a - 12p	PSS Upgrade BPM, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Harp, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Harp, Viewer, Wien Work CIS Rack Work	PSS Upgrade BPM, Harp, Viewer, Wien Work CIS Rack Work	PSS Upgrade Harp, Viewer, Wien Work CIS Rack Work
Tunnel 9a - 12p	Viewer cable pulls	S&A Sets New(er) Points DC Power Resistor Box Button-Up	INSTALL Pedestals, base pads, solenoid stand drilling	Viewer Cable Pulls 11a: Laser Safety System Audit	S&A Survey Pedestals
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	M	S&A Sets New(er) Points	Cable pulls?	R	S&A Survey Pedestals

Week 9 (Nov 16 - Nov 20)

Non-Tunnel Work

1. Continue preparing new Y-chamber
2. A1/A2 cube assemblies - (2) for vacuum testing, (1) for magnet fit-up/testing
3. Prebuncher -- RF testing/tuning
4. Wien-mania! (high level schedule) =>
   • Review V-wien magnetic field mapping results and determine any remaining desired measurements
   • Finish V-wien field mapping and move to horizontal
   • Wien quad hardware arrivals?
   • Install HV switcher chassis
5. 200kV PSS kicker fabrication

Tunnel work

1. INSTALL grouts in pedestals (Mon/Tue) done?
2. Fire pipe demo (Wed/Thur/Fri)

ISB Work

1. Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos)
2. PSS Upgrades -- now at many racks, from IN01B02->IN04B14, afternoons (Beizer)
3. Viewer upgrades, IN03B07 (Norris)
4. Harp upgrades, IN03B07 (Dela Cruz)
5. CIS Rack Work, IN01B{00-05} (Windham)

Injector Tunnel and Service Building

Location Time	Mon 11/16	Tue 11/17	Wed 11/18	Thu 11/19	Fri 11/20
InjSB 5a - 9a	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work
Tunnel 5a - 9a	INSTALL Grout pedestals	T	Fire pipe demo	Fire pipe demo	Lifting Plate Load Test
InjSB 9a - 12p	Viewer, Harp, Wien Work CIS Rack Work	Viewer, Harp, Wien Work CIS Rack Work	Harp, Viewer, Wien Work CIS Rack Work	Harp, Viewer, Wien Work CIS Rack Work	Harp, Viewer, Wien Work CIS Rack Work
Tunnel 9a - 12p	INSTALL Grout pedestals	Laser room/table work Ceiling Lifting Plate Install	Fire pipe demo	Fire pipe demo	F
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	M	Laser room/table work	Fire pipe demo	Fire pipe demo	F

Week 10 (Nov 23 - Nov 25 🦃)

Non-Tunnel Work

1. Complete assembly of new Y-chamber
2. Magnetic mapping of spare aperture cube
3. A1/A2 cube assemblies - (2) for vacuum testing, (1) for magnet fit-up/testing
4. Prebuncher -- RF testing/tuning
5. Wien-mania! (high level schedule) =>
   • Horizontal Wien magnetic assembly and field mapping
   • Bake V-wien electrode assembly with vacuum chamber
   • V-wien HV test at UITF
   • Resistor box testing at UITF?

Tunnel work

1. Opportunistic cable pulls -- who wants to do some? Good week for it.

ISB Work

1. Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos)
2. PSS Upgrades -- now at many racks, from IN01B02->IN04B14, afternoons (Beizer)
3. Viewer upgrades, IN03B07 (Norris)
4. Harp upgrades, IN03B07 (Dela Cruz)
5. CIS Rack Work, IN01B{00-05} (Windham)

Injector Tunnel and Service Building

Location Time	Mon 11/23	Tue 11/24	Wed 11/25	Thu 🦃 11/26	Fri 11/27
InjSB 5a - 9a	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work	Viewer, Harp, Wien Work
Tunnel 5a - 9a	M	T	W
InjSB 9a - 12p	Viewer, Harp, Wien Work CIS Rack Work	Viewer, Harp, Wien Work CIS Rack Work	Harp, Viewer, Wien Work CIS Rack Work
Tunnel 9a - 12p	M	T	W
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	M	T	W

Week 11 (Nov 30 - Dec 4)

Non-Tunnel Work

• H-Wien
  • plate ready at shop, mic and test fit @ MMF
  • order (4) Ni plates
• V-Wien
  • Start HV tests @ UITF
• MHD
  • complete thermal test >2.5A
  • measure field profile and BL/I for CED
• DR
  • measure DR per Jay's plan
• A1/A2 cubes
  • complete assembly (coils + aperture), test motion and shorts
  • S&A fiducialize positions (stac5 A1=2/3/4 mm holes, manual A2=4/6/8 mm holes)
• PSS kicker
  • vendor quotes?
  • place order

Tunnel work

• Install
  • Y girder + 2I solenoid from 1137 to tunnel
  • Gun table to foot pads

• S&A
  • Pre-align Y girder
  • Pre-align gun

• PSS/CIS
  • Complete laser bypass
  • Align laser - test at window, viewer hole, cathode/flange

• CIS/S&A
  • 2I solenoid on pedestal
  • 2I vacuum connection (valve to gun)
  • Final align
  • Final laser check

ISB Work

• Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos)
• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• Viewer upgrades, IN03B{06-07} (Norris)
• Harp upgrades, IN03B07 (Dela Cruz)
• CIS Rack Work, IN01B{00-05} (Windham)

Injector Tunnel and Service Building

Location Time	Mon 11/30	Tue 12/1	Wed 12/2	Thu 12/3	Fri 12/4
InjSB 5a - 9a	M	T	W	R	F
Tunnel 5a - 9a	M	INSTALL: Y-chamber, solenoid	PSS Laser Bypass Work	S&A: Pre-align Gun-Y	S&A: Pre-align Gun-Y
InjSB 9a - 12p	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
Tunnel 9a - 12p	M	INSTALL: Y-chamber, solenoid	CIS Laser Hut Work	S&A: Pre-align Gun-Y	S&A: Pre-align Gun-Y CIS Laser Alignment Work
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	M	T	W	S&A: Pre-align Gun-Y	S&A: Pre-align Gun-Y CIS Laser Alignment Work

Week 12 (Dec 7 - Dec 11)

Non-Tunnel Work

• Wien (Test Lab)
  • Test voltage divider box, calibrating UITF Matsusada HV PSs done, opted to use FLUKE 1000:1 V-probe and RMS true-value multimeter
  • U-Wien electrode alignment -- install teflon spacer (CIS) first-pass done, after discussions, may refine
  • Improve V-wien electrode alignment? (S&A) deferred
  • Receive Nickel endplates received, returned after finish found scratched, received again?

• A1/A2 cubes (Test Lab)
  • Assemble fixture mounting plates done
  • Test motion and shorts '
  • Fiducialize positions (stac5 A1=2/3/4 mm holes, manual A2=4/6/8 mm holes) (S&A) awaiting cubes

• Prebuncher - high power testing

• PSS kicker
  • build bids received, choosing one done
  • 12/9: req submitted

• MagTest
  • Wrapping up A2 measurements
  • Wrapping up A1 measurements

Tunnel work

• Wien cable pulls (Dela Cruz)
• Laser alignment work (CIS) complete for this week
• Gun -> Y-chamber vacuum connections (CIS) Thursday/Friday
• Viewer cable terminations (Norris)

ISB Work

• Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz, Carlos)
• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• Viewer upgrades, IN03B{06-07} (Norris)
• Harp upgrades, IN03B07 (Dela Cruz)
• CIS Rack Work, IN01B{00-05} (Windham)

Injector Tunnel and Service Building

Location Time	Mon 12/7	Tue 12/8	Wed 12/9	Thu 12/10	Fri 12/11
InjSB 5a - 9a	M	Viewer/Wien/Harp Work	Viewer/Wien/Harp Work	R	Viewer Terminations
Tunnel 5a - 9a	CIS Laser Work	CIS Laser Work	CIS Laser Work	S&A+CIS Drive Laser Alignment	Locking in NEG-tube BPM locations (CIS+S&A)
InjSB 9a - 12p	CIS Rack Work	CIS Rack Work Viewer/Wien/Harp Work	CIS Rack Work Viewer/Wien/Harp Work	CIS Rack Work	CIS Rack Work Viewer Terminations Wien Cabling Work
Tunnel 9a - 12p	CIS Laser Work	CIS Laser Work- temp Vacuum Window Install Facilities HVAC Investigation	CIS Laser Work	S&A+CIS Drive Laser Alignment	CIS Pump Down Gun S&A Gun/Y-Chamber
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work Viewer Terminations Wien Cabling Work
Tunnel 12p - 4p	CIS Laser Work	CIS Laser Work Facilities HVAC Investigation	CIS Laser Work	S&A+CIS Drive Laser Alignment	CIS Pump Down Gun S&A Gun/Y-Chamber

Week 13 (Dec 14 - Dec 18)

Non-Tunnel Work

• Wien (Test Lab)
  • U-Wien electrode parallelism evaluation after assembly w/teflon spacer block, spacer for hangers added (S&A) done
  • Controls work continues yep
  • HV PS calibration measurements, second-pass Friday
  • Receive Nickel endplates? done

• A1/A2 cubes (Test Lab)
  • Assembling A1/A2 cubes done
  • Test motion and shorts done
  • Fiducialize positions (stac5 A1=2/3/4 mm holes, manual A2=4/6/8 mm holes) (S&A) A2 done, A1 completed today

• MagTest
  • Measure DR per Jay's plan continues
  • QW (Wien quad) lead reinforcement and field mapping 4 done, 12 to go

Tunnel work

• Wien cable pulls (Dela Cruz) (latter half of the week) done?
• Viewer cable terminations? (Norris) near complete
• Gun -> Y-chamber vacuum pumpdown and leak check (Stutzman, Adderley) done
• CIS Check drive laser -> cathode -> retroreflection alignment w/assembly under vacuum done
• SSG Backs out of Laser Bypass workaround in support of PSS upgrades Friday

ISB Work

• Wien upgrade work, IN01B{00-03} (Windham, Dela Cruz)
• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• Viewer upgrades, IN03B{06-07} (Norris)
• Harp upgrades, IN03B07 (Dela Cruz)
• CIS Rack Work, IN01B{00-05} (Windham)

Injector Tunnel and Service Building

Location Time	Mon 12/14	Tue 12/15	Wed 12/16	Thu 12/17	Fri 12/18
InjSB 5a - 9a	Viewer Terminations	Viewer Terminations	W	R	F
Tunnel 5a - 9a	CIS Vacuum Work: heating NEG chambers	CIS Vacuum Work: Leak Checks	Wien HV Cable Pulls?	Wien HV Cable Pulls?	F
InjSB 9a - 12p	CIS Rack Work Viewer Terminations	CIS Rack Work Viewer Terminations	CIS Rack Work	CIS Rack Work PSS Upgrades: Access Room and in Racks	CIS Rack Work
Tunnel 9a - 12p	CIS Vacuum Work: heating NEG chambers	CIS Vacuum Work: Leak Checks CIS Laser/retroreflection checks	CIS Laser Hut Work Viewer Terminations Wien HV Cable Pulls?	CIS Laser Hut Work Viewer Terminations	SSG Laser Bypass Backout
InjSB 12p - 4p	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrade CIS Rack Work	PSS Upgrades: Access Room and in Racks CIS Rack Work	PSS Upgrade CIS Rack Work
Tunnel 12p - 4p	CIS Vacuum Work	CIS Vacuum Work CIS Laser/retroreflection checks	CIS Laser Hut Work Viewer Terminations	CIS Laser Hut Work Viewer Terminations	F

Week 13.6 (Dec 21 - Dec 23)

830 toolbox meetings suspended.
Have a safe and restful winter break.

Non-Tunnel Work

MagTest --

• DR field mapping continues

Tunnel work

• Neutron detector field cable runs, above 0L03 (Gonzales)
• PSS upgrades -- equipment near Inj-NL gate (SSG)

ISB Work

• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer terminations, IN03B{06, 07} (Norris)
• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere (SSG)
• Neutron detector system work, IN03+4 (Gonzales, Mock)

Week 14 (Jan 4 - Jan 8)

Happy New Year!!! 🎉🎉🎉

• AIPINJ Phase I Jobs for 2021

• Punchlist from 12/17/20 ME meeting media:AIPINJ_2021_Jobs_v3.pdf

Non-Tunnel Work

• Wien
  • V-Wien (Hernandez-Garcia)
    • remove from UITF test stand
    • re-assemble in Vertical orientation w/new spacers, Ni endplates, and magnet
    • ~Wed deliver to S&A
    • Survey of V-wien, evaluation of electrode parallelism
  • Picking up new Ni endplates from machine shop, cleaning and annealing before delivery to MagTest to be used in assembly of H-wien and evaluation during field mapping (Grames)
  • Fabrication of HV switcher chassis continues (Dela Cruz)
  • Controls work continues (Croke)
• A1/A2 Apertures
  • Motor controls work continues (Windham)
  • A1/A2 girder build in TL continues (Adderley)
• MagTest
  • DR field mapping
  • Complete QW coils lead reinforcement and mapping
  • Begin H-wien field mapping?

Tunnel work

• Prepping for Gun2 bake (Stutzman)
• Wien HV cable pulls? (Dela Cruz, Norris)
• Laser hut opto-mechanical work (Zhang)
• LCW walkthrough (CIS+I&C+MechInstall)

ISB Work

• Wien HV cable pulls?, IN01B{00+01} (Dela Cruz, Norris)
• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel install, IN01B11 (Windham)
• iocin3 crate upgrade to VME, IN01B{04+14} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 1/4	Tue 1/5	Wed 1/6	Thu 1/7	Fri 1/8
InjSB 5a - 9a	M	T	W	R	F
Tunnel 5a - 9a	M	Wien HV cable pulls?	MechInstall Crane Work Wien HV cable pulls? Viewer Terminations	Wien HV cable pulls? Viewer Terminations	Wien HV cable pulls? Viewer Terminations
InjSB 9a - 12p	CIS Rack Work	CIS Rack Work -- 15deg Interlocks Panel	CIS Rack Work iocin3 crate upgrade prep	15deg Interlocks Panel	CIS Rack Work
Tunnel 9a - 12p	Gun2 Bake Preps	9a LCW Manifold WalkThru Gun2 Bake Preps Viewer Terminations	Gun2 Bake Preps Viewer Terminations	Gun2 Bake Preps Viewer Terminations	Gun2 Bake Preps Viewer Terminations
InjSB 12p - 4p	CIS Rack Work PSS Upgrades	CIS Rack Work -- 15deg Interlocks Panel PSS Upgrades	CIS Rack Work iocin3 crate upgrade prep PSS Upgrades	15deg Interlocks Panel PSS Upgrades	CIS Rack Work PSS Upgrades
Tunnel 12p - 4p	Gun2 Bake Preps	Gun2 Bake Preps	Gun2 Bake Preps	Gun2 Bake Preps	Gun2 Bake Preps

Week 15 (Jan 11 - Jan 15)

Non-Tunnel Work

• Wien (Hernandez-Garcia)
  • Bake V-wien
  • V-wien HV soak
  • Fabrication of HV switcher chassis (Dela Cruz)
• A1/A2 girder build (Adderley)
• Rectify viewer air cylinder lengths? (Stutzman)

• MagTest
  • DR field mapping
  • Complete QW coils lead reinforcement and mapping
  • Begin H-wien field mapping?

Tunnel work

• Photocathode suitcase bake (Stutzman, Adderley)
• Wien HV cable pulls? (Dela Cruz, Norris)
• Laser hut work (Zhang)
• iocin3 job Tuesday

Gun HV control => no problem

Some vacuum => no problem

Some FSD => no problem

Insertables (viewers etc.) => no problem

Some Pockels cell & RTP cell controls => i turned off RTP HV PS already

Chopping aperture (not sure how current this is) => no problem

Scraper (think this is redundant?) => do we remove now???

Maybe some old laser controls (ocelot?) => is this really a running app???

An application called pol_source, which has controls for a number of boards - IP Digital 24, BASIC stepper motor, IpOpto. => => what is this connected to???

Are the remaining 4-laser apps on iocin3b? Will that mini-crate be replaced or merged? Any other apps on iocin3?

ISB Work

• ⚡⚡⚡Power Outage⚡⚡⚡ I-BT Breaker Panel Work -- adding 50A circuit for new chopper SSA along with 225A main breaker
  Details of what will lose power in ATLis 21696, Tunnel and SB racks affected
• PSS Upgrades -- energizing new equipment, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel install, IN01B11 (Windham)
• iocin3 crate upgrade to VME, IN01B{04 + 14} (Dela Cruz)
  • iocin3 will be down Monday 1/11 morning

Injector Tunnel and Service Building

Location Time	Mon 1/11	Tue 1/12	Wed 1/13	Thu 1/14	Fri 1/15
InjSB All Day	Safing out equipment for iocin3 work	T	W	Breaker Panel Work	Float for breaker panel work
InjSB Morning	M	iocin3 VME upgrade 15deg interlock work	W	Breaker Panel Work	F
InjSB Afternoon	PSS Upgrades	15deg interlock work PSS Upgrades	PSS Upgrades	Breaker Panel Work PSS Upgrades	PSS Upgrades
Tunnel All Day	Suitcase bake Safing out equipment for iocin3 work	Suitcase bake	W	Breaker Panel Work	Float for breaker panel work
Tunnel Morning	M	T	W	Breaker Panel Work	F
Tunnel Afternoon	M	T	W	Breaker Panel Work	F

Week 16 (Jan 18 - Jan 22 +weekend)

Non-Tunnel Work

• Wien (Hernandez-Garcia)
  • Moving V-wien from UITF test stand to vacuum lab, w/local vac PS Leaving on test stand until need to move
  • H-Wien
    • Preparing to receive Wed 1/20 Fri 1/22
    • Assemble with Ni end plates
    • UHV cleaning

• A1/A2 girder build (Adderley, Stutzman)
  • Rectifying viewer air cylinder dimensions

• Prebuncher testing/tuning (Wissman)

• MagTest
  • H-wien field mapping (ETA Fri 1/22)
  • DR#2 coil lead reinforcement
  • DR#1 upper coil inspection

Tunnel work

• Fire pipe install, pipe delivery 1/22, install begins Saturday 1/23
• Wien HV cable pulls? (Dela Cruz, Norris)
• Laser hut work (Zhang)
• Vacuum bakes (Stutzman, Adderley)
• FC#1 bellows replacement (Adderley, Stutzman, Grames)

ISB Work

• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel install, IN01B11 (Windham)
• Chopper SSA upgrade, back of IN01B{10-15} (Farrish)

Injector Tunnel and Service Building

Location Time	Mon 1/18 MLK Jr Day	Tue 1/19	Wed 1/20	Thu 1/21	Fri 1/22	Weekend Sa 23rd + Su 24th
InjSB All Day	holiday	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	weekend
InjSB Morning	M	Beam Sync Cabling Check (~IN01B04) Francis 15deg Interlock Chopper SSA Cabling	W	CIS Rack Work	CIS Rack Work	weekend
InjSB Afternoon	M	15deg Interlock PSS Upgrades	Laser chiller checkout PSS Upgrades	CIS Rack Work PSS Upgrades	CIS Rack Work PSS Upgrades	weekend
Tunnel All Day	holiday	Laser Hut Work Vacuum Bakes	FC#1 Bellows Replacement	R	Fire pipe install	Fire pipe install
Tunnel Morning	M	T	W	FC#1 Vacuum Button-Up Viewer Terminations	Fire pipe install	Fire pipe install
Tunnel Afternoon	M	T	Laser Hut Work	FC#1 Vacuum Button-Up Laser Hut Work	Fire pipe install	Fire pipe install

Week 17 (Jan 25 - Jan 29)

Non-Tunnel Work

• Wien (Hernandez-Garcia)
  • H-Wien
    • Receive from MagTest after field mapping
    • Assemble with Ni end plates
    • UHV cleaning
  • U-Wien newly fabricated Ni endplates
    • Pick-up after ultrasonic isopropanol clean 1/25
    • Deliver for annealing
  • V-Wien
    • Remove from UITF cave and begin assembling on girder?
• A1/A2 girder build (Adderley, Stutzman)
• Rectifying viewer air cylinder dimensions (Adderley, Machie, Gregory)
• Prebuncher testing/tuning (Wissman)

• Survey and Alignment
  • PCup survey and fiducialization
  • FC#1 survey and fiducialization
  • H-wien after UHV cleaning and assembly using teflon spacer method
  • Individual H-wien electrodes, and U-wien ones for comparison

• MagTest
  • QW coil thermal tests
  • QW coil quality control checks

Tunnel work

• Fire pipe (FML subcontractor)
  • Install
  • Pressurized air test
  • Pressurized water test (hydrotest)
• Laser hut work (Zhang)
• Preps for prep-chamber and HV chamber bakes next week (Stutzman, Adderley)
• 120V front-end outlets walkthru (Windham, Stutzman, Adderley, Grames)
• Cryo relief valve PM, behind 0L02 (Cryo)
• Stowing photocathodes in suitcase for bakes (Grames)
• Gate valve controller checkout/documentation (Windham)

ISB Work

• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel, IN01B11 (Windham)
• Utility chassis swaps, IN02B{10,11,26} + IN04B10 (Diggs, Kissinger)

Injector Tunnel and Service Building

Location Time	Mon 1/25	Tue 1/26	Wed 1/27	Thu 1/28	Fri 1/29
InjSB All Day	M	Fire pipe install	W	Utility chassis swaps	F
InjSB Morning	M	Fire pipe install	W	Utility chassis swaps	F
InjSB Afternoon	PSS Upgrades	Fire pipe install PSS Upgrades	PSS Upgrades	Utility chassis swaps PSS Upgrades	PSS Upgrades
Tunnel All Day	Fire pipe install	Fire pipe install	Fire pipe install	Cryo relief valve PM	Fire pipe hydrotest
Tunnel Morning	Fire pipe install	Fire pipe install	Fire pipe install	120V outlets walkthru Fire pipe air test	Fire pipe hydrotest Valve controller
Tunnel Afternoon	Fire pipe install	Fire pipe install	Fire pipe install Laser Hut Work	Laser Hut Work	Preps for bakes? Photocathodes->Suitcase? Laser Hut Work

Week 18 (Feb 1 - Feb 5)

Non-Tunnel Work

• Wien (Hernandez-Garcia)
  • H-Wien
    • MS fabricating new frame x4 and
      new 14mm-spacing teflon spacers for electrode assembly
    • Once MS done, towards end of the week, assemble H-wien w/new frame
    • Assembled H-wien -> S&A
  • HV Switcher Chassis (Dela Cruz)
    • 1st chassis hi-potted good
    • 2nd chassis getting overload faults, investigating
• Viewer assembly (Adderley, Stutzman)
• Wien girder assembly (Adderley, Stutzman)
  • Wien quads on crosses -- ETA T/W for QW coils from MagTest
• Add pumps, vacuum leak check A1/A2 girder after S&A (Stutzman, Adderley)
• Laser box build (Zhang, Gregory)
• Build spare valve override blackbox, fourth in total (Windham)

• Survey and Alignment
  • A1/A2 girder 1A pre-alignment
  • H-wien assembled on new frame

• MagTest
  • Finish QC of QW coils -- Tuesday/Wednesday ETA
  • Thermal and current-limit tests on assembled spare QW-quad
  • Field mapping assembled spare QW-quad

Tunnel work

• Laser hut work (Zhang)
• Viewer upgrades (Norris)
• Prep chamber bake forgoing for now, vacuum sufficiently good
  • Setup (in no particular order)
    • photocathodes->suitcase;
    • breakdown unistrut,
    • stow protective plastic barrier;
    • Configure IPs and valves
  • Bake for ~3 days @ 🔥🔥🔥C
  • Breakdown ~Friday
• Opportunistic preps for HV chamber bake
• 120V front-end outlets walkthru (Windham, Stutzman, Adderley, Grames)
• Laser box enclosure design walkthru (Zhang, Gregory)
• N2 manifold temporary move (Bullard)

ISB Work

• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel, IN01B11 (Windham)
• Install Wien HV Polarity Switcher Chassis, IN01B0{0,1} (Dela Cruz)

Other Service Buildings

• Prebuncher testing/tuning in BSY SB (Wissman)

Injector Tunnel and Service Building

Location Time	Mon 2/1	Tue 2/2	Wed 2/3	Thu 2/4	Fri 2/5
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	F(loat)
InjSB Morning	M	15deg dipole intlk tests Viewer upgrades	15deg dipole intlk tests Viewer upgrades	R	Viewer Upgrades
InjSB Afternoon	PSS Upgrades	15deg dipole intlk tests PSS Upgrades	PSS Upgrades	15deg dipole intlk tests PSS Upgrades	PSS Upgrades
Tunnel All Day	Prep for Prep Chamber Bake	Prep chamber bake Preps for HV Chamber Bake	Prep Chamber Bake Preps for HV Chamber Bake	Prep Chamber Bake Preps for HV Chamber Bake	F(loast)
Tunnel Morning	Valve controller	Prep chamber vacuum tests/eval	Viewer Upgrades Engaging Prep RGA N2 manifold move?	N2 manifold move Laser enclosure walkthru	Viewer Upgrades N2 manifold work
Tunnel Afternoon	Photocathodes->Suitcase Valve controller	Laser hut work	Laser enclosure walkthru Laser hut work	Laser hut work	Laser hut work

Week 19 (Feb 8 - Feb 12)

Non-Tunnel Work

• Weld Jobs: QW quads on crosses, Wien cube
• A1/A2 Girder (Adderley, Stutzman)
  • Final leak check, prep for install in tunnel
• Wien (Hernandez-Garcia)
  • H-wien
    • S&A, Monday
    • Bake
    • Vacuum pumpdown
    • HV testing?
  • V-wien
    • Unmount from test fixture in UITF
    • Prepare for girder install

Tunnel work

• Viewer upgrades
• A1/A2 girder install
  • Vacuum prep work (Stutzman, Adderley), Monday
  • Install (Mech Install), Tuesday
  • S&A, Tue-Thu
  • Associated vacuum work, Tue-Thu
• FC#1 Re-install
  • Vacuum prep work (Stutzman, Adderley), Monday
  • Re-install + S&A, Tuesday
  • Vacuum space pumpdown (Stutzman, Adderley), Tue-Thu
• Laser hut work (Zhang)
• Laser enclosure design/fab (Zhang, Gregory)

ISB Work

• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-05} (Windham)
• Viewer upgrades, IN03B{06+07} (Norris)
• 15deg dipole interlock panel, IN01B11 (Windham)
• Install HV Polarity Switcher Chassis, IN01B0{0,1} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 2/8	Tue 2/9	Wed 2/10 1p: AIPINJ team photo (zoom)	Thu 2/11	🌨️ Fri 2/12
InjSB All Day	15deg interlock	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	M	T	Viewer Upgrades	R	F
InjSB Afternoon	PSS Upgrades	PSS Upgrades	PSS Upgrades	PSS Upgrades	PSS Upgrades
Tunnel All Day	Preps for FC1+A1/A2 Install	Vent Gun->0I; FC#1 + A1/A2 Girder Install, Associated Vac Work, S&A	S&A of A1/A2 Girder, after cartridge swap	Preps for HV Chamber Bake Prep NEG Activation	Preps for HV Chamber Bake Prep NEG Activation
Tunnel Morning	Pump Cart Staging	7a: Vent Gun2->0I (CIS) 7a: FC#1 Re-Install (CIS) ~8a: FC#1 S&A, set yaw A1/A2 Girder Install (Mech)	Cartridge Swap (MechInstall) S&A of A1/A2 Girder 0L Viewer upgrades	S&A of A1/A2 Girder A1/A2 Cartridge Layout 9a-11a: "Tour" (4people)	S&A of A1/A2?
Tunnel Afternoon	Laser Hut Work	A1/A2 Girder S&A Laser hut work?	S&A of A1/A2 Girder A1/A2 vac connections Prep Chamber RGA v Heat	Cartridge Layout	S&A of A1/A2?

Week 20 (Feb 15 - Feb 19)

Non-Tunnel Work

• Wien girder assembly (Adderley, Stutzman)
• H-wien HV testing at UITF (once bake complete) (Hernandez-Garcia, Bullard)
• QW field mapping (MagTest)
• PSS Kicker assembly once parts arrive

Tunnel work

• HV Chamber and NEG tube bake (Adderley, Stutzman)
• Prep chamber NEG activation (Adderley, Stutzman)
• A1/A2 girder cartridge resolution?
• Wien HV cable pulls? (Dela Cruz)
• Viewer upgrades? (Norris)
• UHV patch panel installation (Windham)
• Valve black override box installation (Windham)

ISB Work

• PSS Upgrades, IN02B{NI,29,30} +briefly elsewhere, afternoons (Beizer)
• CIS Rack Work, IN01B{00-12} (Windham)
• Viewer upgrades, IN03B0{6,7} (Norris)
• Install Wien HV Polarity Switcher Chassis, IN01B0{0,1} (Dela Cruz)
  • HV cable pulls?

Injector Tunnel and Service Building

Location Time	🇺🇸 Monday 2/15	Tue 2/16	Wed 2/17	Thu 2/18	Fri 2/19
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	Switcher chassis install	Switcher chassis install Wien controls test	Switcher chassis install Wien controls tests	R	F
InjSB Afternoon	PSS Upgrades	PSS Upgrades	PSS Upgrades	PSS Upgrades Lock-Up @ 1600	PSS Upgrades
Tunnel All Day	HV Chamber + NEG Tube Bake	HV Chamber + NEG Tube Bake	HV Chamber + NEG Tube Bake	HV Chamber + NEG Tube Bake	HV Chamber Bake NEG Tube Activation Prep Chamber NEG Activation
Tunnel Morning	M	T	W	R	10a: Outlet relocation walkthru
Tunnel Afternoon	M	T	W	R	F

Week 21 (Feb 22 - Feb 26)

Non-Tunnel Work

• H-wien HV evaluation (Hernandez-Garcia, Bullard)
• Wien girder modifications (Machine Shop)
• QW field mapping (MagTest)
• PSS Kicker assembly

Tunnel work

• Breaking down activation and bake equipment (Stutzman, Adderley)
• PSS Injector Segment Certification (SSG) Th+F Swing
• A1/A2 Girder
  • Add SS adapter plates (CIS)
  • Re-fiducialize girder, MechInstall staging as needed (S&A)
  • Install on pedestals (MechInstall) Thursday
  • S&A of installed girder on pedestals Thursday
  • Vacuum hook-ups (CIS) Thursday
• Laser hut work (Zhang)
• Outlet Moves / Additions (FML) Friday
  • Move from floor to laser hut wall 120V outlets
  • ATLis 21922
• Support Electrical Panel PM
  • Vacuum pump reconfigs from EM -> House power and back (CIS)
  • ATlis 21882

ISB Work

• PSS Commissioning, IN02B{NI,29,30} +briefly elsewhere, swings (SSG)
• PSS Injector Segment Certification (SSG) Th+F swing
• CIS Rack Work, IN01* (Windham)
• Viewer upgrades, IN03B0{6,7} (Norris)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)
• Electrical panel PM, ATLis 21882 (FML) Friday
  • Work entails power outages in tunnel and SB
  • EM loop and normal power will not be off simultaneously
  • Facilities/Operability will coordinate -- see rough sched in table
• Fan tray swap, ATLis 20311, IN02B23 (Greenfield) Friday 8a

Injector Tunnel and Service Building

Location Time	Mon 2/22	Tue 2/23	Wed 2/24	Thu 2/25	Fri 2/26
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	Electrical Work some power outages
InjSB Morning	M	T	W	R	8a Fan Tray Swap
InjSB Afternoon	M	PSS Tests, Lock-Up	W	PSS Certification	PSS Certification
Tunnel All Day	Bake and Activation Equipment Breakdown	A1/A2 re-fiducialization	W	A1/A2 Install Day	Electrical Work some power outages
Tunnel Morning	Leak checks of *HV Chamber *Prep Chamber *2I beamline	Re-fiducialization of A1/A2 Valve override box work	W	MechInstall adds adapter plates Mounts on pedestals S&A & Vac Hook-Ups	Floor Outlet Relocation
Tunnel Afternoon	M	PSS Lock-Up	W	A1/A2 S&A 3p PSS Certs Lock-Up Some Preps Beginning ~2p	~1p: House Circuits PM ~2p: Pump reconfig EM=>HOUSE ~230p: EM Circuits PM ~3p: PM done, Return pump config ~after: PSS Certs Lock-Up (if needed)

Week 22 (Mar 1- Mar 5)

Non-Tunnel Work

• Wien girder assembly (CIS)
  • Mounting modifications complete, returned from Hampton MS
  • Additional holes for mounting/anchoring needed? Template from Engineering. (Gregory)
  • CIS+S&A Walk-thru identifying which components need alignment during assembly stage
  • Add component, survey, align *repeat*

• PSS Kicker (SSG)
  • Coil QA (MagTest)
  • Assembly (CIS)
  • Coils and fixture in. What other parts needed?
• QW quad field mapping (MagTest)
• Move PIG to InjSB

Tunnel work

• A1/A2 girder anchoring (Adderley, Gregory)
  • S&A Alignment check before vacuum hook-ups
• A1/A2 / Region 3 Vacuum Connections, Pumpdown, Leak check (CIS)
• Wien girder pedestal re-positioning (MechInstall)
  • Remove pedestals, knock out existing grout
  • Pedestals to new positions, templates provided by Engineering
  • Grout in
• Crane in PIG HV resistor tank (MechInstall)
• Macropulse chassis checkout (Zhang, Windham)
• Laser hut alignment / opto-mechanical work (Zhang)
• Pockels cell alignment (Zhang, Amali)
• Gun HV Conditioning preparations (Hernandez-Garcia)
• Beam-left S&A monument install (x4), adding to control, ATLis 21991 (S&A) Thursday
• Lead brick clean-up (Grames)

ISB Work

• Wien HV Polarity Switcher Tests, Control Screens Checkouts, IN01B0{0-6} (Hernandez-Garcia, Windham, Dela Cruz, Croke)
• CIS Rack Work, IN01* (Windham)
• Viewer upgrades, IN03B0{6,7} (Norris)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)
• SCAM Board Investigation, IN03B04 (Windham)

Injector Tunnel and Service Building

Location Time	Mon 3/1	Tue 3/2	Wed 3/3	Thu 3/4	Fri 3/5
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	M	T	930 Wien Switcher Tests	SCAM Board T/S Prebuncher Cable Pulls	F
InjSB Afternoon	M	T	Macropulse Chassis Checkout	R	F
Tunnel All Day	A1/A2 anchoring	A1/A2 Vacuum hook-ups pumpdown	Relocating Wien Pedestals	A1/A2 Girder Bake Oven Setup	A1/A2 Girder Bake Oven Setup
Tunnel Morning	Wien stand demo A1/A2 Anchoring	A1/A2 Vacuum Hook-Ups 0I02 Harp Re-Install	MechInstall: * Crane in PIG * Set Wien Pedestals S&A: Align	Prebuncher cable pulls S&A Monuments	F
Tunnel Afternoon	A1/A2 Anchoring Alignment Check Pockels Cell Alignment	A1/A2 Pumpdown Pockels Cell Alignment	A1/A2 girder leak check	Region 3 leak checks Macropulse chassis checkout Pockels cell alignment	Lead brick clean-up

Week 23 (Mar 8 - Mar 12)

Non-Tunnel Work

• Wien girder assembly, interleaved with component S&A (Stutzman, Adderley)
• PSS Kicker (SSG)
  • Coil QA (MagTest)
  • Assembly (CIS)

Tunnel work

• A1/A2 Girder bake (Adderley, Bullard, Stutzman)
• Gun HV Processing Setup (Hernandez-Garcia)
  • PIG connections
  • SF6 tests
  • Interlock jumpering/configuration (Grames, Windham)
  • PSS Certification of Gun HV (SSG, Forman) Wed 9a, lock-up
• Wien pedestal grouting opportunistic
• Pockels cell alignment (Zhang, Amali)
• Macropulse chassis modification and checkout (Windham, Zhang)
• Lead brick clean-up (Grames)

ISB Work

• CIS Rack Work, IN01*
• Viewer upgrades, IN03B0{6,7} (Norris)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 3/8	Tue 3/9	Wed 3/10	Thu 3/11	Fri 3/12
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	M	T	W	R	F
InjSB Afternoon	M	T	W	R	F
Tunnel All Day	A1/A2 Girder Bake	A1/A2 Girder Bake	A1/A2 Girder Bake	A1/A2 Girder Bake	A1/A2 Girder Bake
Tunnel Morning	Gun HV Processing Setup: *Connect PIG *SF6 Tests	Gun Interlocks Config Jumpering	9a: Lock-Up for Gun PSS Certs	R	F
Tunnel Afternoon	Pockels cell alignment	Pockels cell alignment	Macropulse chassis mods	R	F

Week 24 (Mar 15 - Mar 19)

Phase 1 - HCO & Commissioning

Non-Tunnel Work

• Complete assembly of Wien girder (CIS)
  • Pumpdown and leak check
  • Add viewers with modified shafts
  • Component 1B alignment (S&A)
• PSS Kicker Assembly (CIS)

Tunnel work

• A1/A2 girder bake disassembly, leak checks (Adderley, Bullard, Stutzman)
• PSS Kicker conduit, kapton insulation, install (SSG)
• UHV system labelling, documentation (Windham)
• Cable tray spec'ing, install, under A1/A2 girder (Windham)
• Wien girder install (in approximate order) --
  • Install girder (MechInstall)
  • 2A alignment (S&A)
  • Vacuum connections, rough pumpdown, leak check (CIS)
  • Grout pedestals (MechInstall, S&A)
  • 2B alignment (S&A)
• DC Power magnet hook-ups, as possible (Coleman, +1)
• DC Power resistor box work (Coleman, +1)
• Prep chamber activation check (Grames)
• Laser hut work (Zhang)
• Gun HV checkout (Hernandez-Garcia)
  • Lock-up on swings ??
  • DecaRad placement (Windham)
  • Anode picoammeter connection (Grames, Stutzman)
  • Backfill SF6 into gun, PIG (Bullard)
• Pockels cell alignment (Amali, Zhang)

ISB Work

• CIS Rack Work, IN01* (Windham)
• Viewer upgrades, IN03B0{6,7} (Norris)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 3/15	Tue 3/16	Wed 3/17	Thu 3/18	Fri 3/19
InjSB All Day	CIS Rack Work UHV Sys Doc	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	M	T	W	R	F
InjSB Afternoon	M	T	W	R	F
Tunnel All Day	A1/A2 Bake Takedown Leak Check	A1/A2 Bake Takedown Leak Check	A1/A2 Bake Takedown Cable Tray Work	R	DC Power Inline Resistor Measurements SRF CM Checkout
Tunnel Morning	UHV Sys Doc	Backfill SF6 DecaRad placement	Pockels cell alignment	Wien Pedestal Anchor Hole Drilling A1 controls/spacing work ~10a: Pockels cell alignment	until 10a: A1 aperture work ~9a: Pockels cell alignment 930-11a: Lead brick clean-up 10a DCP Inline Res
Tunnel Afternoon	Pockels cell alignment UHV Sys Doc	Pockels cell alignment DecaRad Placement Gun anode hook-up	Pockels cell alignment 130p: Resistor box work	A1 controls/spacing work Pockels cell alignment	Pockels cell alignment DCP Inline Res

Week 25 (Mar 22 - Mar 26)

Phase 1 - HCO & Commissioning

Non-Tunnel Work

• PSS Kicker Assembly (CIS)

Tunnel work

• PSS Kicker conduit, kapton insulation, install (SSG)
• Cable tray install, under A1/A2 girder (Windham)
• Wien girder install (in approximate order) --
  • Install girder (MechInstall)
  • 2A alignment (S&A)
  • Vacuum connections, rough pumpdown, leak check (CIS)
  • Grout pedestals (MechInstall, S&A)
  • 2B alignment (S&A)
• Setting up for Wien girder bake (CIS)
• DC Power magnet hook-ups, as possible (Coleman, +1)
• Survey checks of Wien <=> A1/A2 girder (S&A)
• Laser hut work, pockels/RTP cell alignment (Zhang)
• Helicity board beam sync fiber T/S (Suleiman, Windham, Francis)
• Gun HV Assessment, Injector->Power Permit (Hernandez-Garcia)
• PSS Kicker mounting spool swap (Adderley, Stutzman)

ISB Work

• CIS Rack Work, IN01* (Windham)
• Viewer/Harp upgrades, IN03B0{6,7} (Norris/Dela Cruz)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 3/22	Tue 3/23	Wed 3/24	Thu 3/25	Fri 3/26
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	Craning Wien Girder	T	W	R	F
InjSB Afternoon	M	T	W	R	F
Tunnel All Day	Wien girder install, S&A, vac hook-up	Wien girder leak checks Gun HV Assessment Preps	Kicker spool swap	A1 Bake Setup	A1 Bake
Tunnel Morning	MechInstall Wien girder and S&A	* Wien girder <=> A1/A2 Girder Flange alignment assessment * Wien girder leak checks * Gun HVPS Lock -> FC#1 Air line	930a Swapping Kicker Spool A1 Pumpdown	* PSS Kicker Fit Test * A1 Bake Setup * Yellow laser box removal *	Helicity Board T/S
Tunnel Afternoon	Wien girder S&A and vacuum hook-ups, pumpdown Pockels cell alignment	Wien girder leak checks Laser hut work 5p: Lock-Up -> PP	A1 Pumpdown, Leak check Laser hut work 4p: Lock-Up Gun HV assessment	A1 Bake Setup Laser hut work 4p: Lock-Up Gun HV assessment	Laser hut work

Week 26 (Mar 29 - Apr 2)

Phase 1 - HCO & Commissioning

Non-Tunnel Work

• Evaluation of prebuncher options for CEBAF (CIS, RF, Eng)
• Laser enclosure build (Bullard, Machie)

Tunnel work

• 0L02 U-tube installs (Cryo)
• AIPINJ Phase-II As-Found survey (S&A)
• Laser hut work (Zhang)
• Pb brick clean-up (MechInstall, Grames)
• Penetration re-fills (MechInstall)
  • Holding off on laser hut penetration until after Wien bake
• Gun HV Assessment, Injector Lock-up (Hernandez-Garcia)
• Prebuncher install, S&A, vacuum rough down (Stutzman, Adderley)
• Craning out heavy equipment in tunnel (MechInstall)
• Grout Wien pedestals (MechInstall)
• Vacuum Bakes (Adderley, Stutzman)
  • Wrap up A1 bake
  • Disassemble A1 bake setup
  • Setup for Wien girder bake, after prebuncher install
  • Wien girder bake

ISB Work

• CIS Rack Work, IN01* (Windham)
  • Laser seed lockout walkthru with ES&H (Windham)
• Viewer CAMAC->VME upgrades, IN03B0{6,7} (Norris)
• Harp -> PC104 upgrades, IN03B0{6,7} (Dela Cruz)
• Penetration re-fills (MechInstall)
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)
• Helicity board beam sync troubleshooting (Suleiman)

Injector Tunnel and Service Building

Location Time	Mon 3/29	Tue 3/30	Wed 3/31	Thu 4/1	Fri 4/2
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	M	T	Craning Out Heavy Equipment	R	Penetration Fills: 58, 86, 108
InjSB Afternoon	M	T	W	Laser seed lock-out walkthru	2p: Helicity Board Beam Sync T/S Mott System Turn On
Tunnel All Day	A1 Bake Takedown 5D Line removal SS Prebuncher Install	Prebuncher S&A, Vacuum Work	Wien girder bake setup S&A Phase II As-Founds	Wien girder bake setup/begin	Wien girder bake
Tunnel Morning	0700: 5D line removal Pb brick org walk-thru	9a: S&A of prebuncher 0L02 U-Tube Install	Penetration Closures Craning Out Heavy Equipment 0L04 U-tube installs	Wien bake controls check Wien bake insulation Penetration Closures	Penetration Closures
Tunnel Afternoon	A1-region leak check Laser hut work RTP Cell Documentation	Prebuncher leak checks Wien girder bake setup Laser hut work	1p: PSS Conduit WalkThru Laser hut work	Begin Wien girder bake Laser hut work	Laser hut work

Week 27 (Apr 5 - Apr 9)

Phase 1 - HCO & Commissioning

Non-Tunnel Work

• Laser box build (Bullard) ✅

Tunnel work

• Wien girder bake, bake takedown, leak check (Stutzman, Adderley) : Tuesday ✅
• A1 cable terminations (Windham) Tuesday ✅
• NEG activations (nine in total) (Stutzman, Adderley) : Monday ✅
• Install under-girder cable trays (Electricians, Windham) : Thur ✅
  • Job WalkThru Tuesday
• Bond girders (Electricians, Windham) : Thur ✅
• Move/attach HV patch box for UHV pumps (Adderley) : Fri ✅
• Install PSS Kicker conduit (Bruhwel) : Fri ✅
• Grout Wien pedestals (MechInstall) : Fri ✅
• Laser box install (Bullard, Zhang) : next Monday
• Attach 15deg (DR) Dipole (CIS) : next Monday
• Re-attach Haimson (BH) corrector pairs (Adderley, Grames) : next Monday
• Re-attach Wien-quad (QW) fixtures (Adderley, Grames) : next Monday
• Install second air manifold (Bullard, Adderley) : Wed ✅
• Complete LCW manifold install work (MechInstall) : Tues ✅
• Laser hut penetration closure, sealing (no stone), Pb brick shielding (MechInstall) Fri ✅
• Install Wien filter magnets Fri ✅

ISB Work

• CIS Rack Work, IN01* (Windham)
• Penetration re-fills, see Penetration Work below (MechInstall) ✅
• Preps for penetration fills -- as needed, making space for chute to drop stones, IN02B10, IN02B23, IN03B04 (Moser) ✅
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz)
• Mott DAQ VME crate power T/S, IN02B21 (Suleiman) ✅
• Laser seed chassis safe-operation-lock-up work, IN01B05 (Zhang, Windham) ✅

Injector Tunnel and Service Building

Location Time	Mon 4/5	Tue 4/6	Wed 4/7	Thu 4/8	Fri 4/9
InjSB All Day	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work	CIS Rack Work
InjSB Morning	Moving heavy items near crane -> TL	T	Preps for Penetration fills	Preps for Penetration fills	Penetration stone fills (58, 86, 108)
InjSB Afternoon	M	T	W	R	Penetration stone fills (58, 86, 108)
Tunnel All Day	Wien girder bake	Wien bake takedown	CIS Mech Jobs	CIS Mech Jobs Electrician Jobs	MechInstall Jobs SSG Jobs CIS Mech Jobs
Tunnel Morning	NEG Activations	Wien/Y Leak Checks A1 Cable Terminations Cable Tray Job WalkThru	HV Patch Box Move Install 2nd air manifold BH, QW re-attachments	Cable tray install Bond girders BH, QW re-attachments Laser box install	Laser hut pene Grout Wien Pedestals 9a: Kicker Conduit Install Install Wien Magnets Mount HV Patch Box
Tunnel Afternoon	Laser hut work	Laser hut work	Laser hut work	Laser hut work	Laser hut work

Week 28 (Apr 12 - Apr 16)

Phase 1 - HCO & Commissioning

Tunnel work

• System Reconnects and HCO

• Attach 15deg (DR) Dipole (Grames) Mon
• Re-attach Haimson (BH) corrector pairs (Grames) Mon
• Re-attach Wien-quad (QW) fixtures (CIS) Mon

• UHV HV patch box relocation (Adderley) Tues

• Wien pedestals wrap-up -- remove grout forms, cut all threads (MechInstall) Tues
• Under-girder cable tray lowering (Adderley) Tues
• Install laser box (Bullard) T+W
• Remove SS prebuncher bracket interfering with BH corrector placement (CIS?) Tues

• Valve controls work (Ketchum, Windham)

• Vacuum work (Stutzman)
  • Ion pump cabling / controls checks Mon
  • Activating NEGs Mon
  • Hi-potting VIP1I07 Mon
  • Hi-potting VIP1I02 Wed
  • T/S VIP2I00 noise
  • De-gas stalk heater (Grames) Thur

• Magnet hook-ups (DC Power -- Coleman, Delk, Kumar)

• LCW hook-ups (Adderley, Francis)

• 5D Line vacuum disconnects (CIS)

• A1 EPICS controls (Windham, Higgins)

• Gun HV evaluation (Hernandez-Garcia) Swings: W+Th
  • Rapid Access probe placement (Washington) Wed
  • Clean off gun table (CIS) Wed
  • DecaRad placement verification (Hernandez-Garcia) Wed
  • Disconnect and remove PIG (SF6 resistor tank) Thur
  • Install ceiling plate for HV cable strain relief Thur
  • Connect Gun directly to HVPS Thur

• Prebuncher and chopper LCW connections (Wissman) Thur
• Prebuncher cabling (Wissman) Thur

• 60Hz electrical noise snooping (Suleiman)

ISB Work

• System re-connects / associated rack work
• Wien HV cables pulls, IN01B0{0-8} (Dela Cruz) Wed
• A1 EPICS controls work (Windham, Higgins)

Injector Tunnel and Service Building

Location Time	Mon 4/12	Tue 4/13	Wed 4/14	Thu 4/15	Fri 4/16	Sa 4/17	Su 4/18
InjSB All Day	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	Drone Elevation Survey	Su
InjSB Early Morning (<9a)	Associated Rack Work	Associated Rack Work	6a: Wien HV Cable Pulls Associated Rack Work	Associated Rack Work Terminating Wien HV Cables	Associated Rack Work	Sa	Su
InjSB Morning	A1 EPICS controls Associated Rack Work	Associated Rack Work	Associated Rack Work	Associated Rack Work Terminating Wien HV Cables	Associated Rack Work	Sa	Su
InjSB Afternoon	Associated Rack Work	Associated Rack Work	Associated Rack Work A1 EPICS controls	Associated Rack Work	Associated Rack Work	Sa	Su
Tunnel All Day	CIS Vacuum Checkout	CIS Vacuum Checkout	CIS Vacuum Checkout	Air Manifold Plumbing/Install CIS Vacuum Checkout	CIS Vacuum Checkout	Sa	Su
Tunnel Early Morning (<9a)	Wien pedestal wrap-up	Wien pedestal wrap-up	Wien HV Cable Pulls Air Manifold Install Viewer/Valve Solenoid Layout LCW Hook-ups	Viewer/Valve Connections	Viewer/Valve Connections Terminating Wien HV Cables? LCW Hook-ups	Sa	Su
Tunnel Morning	Laser box fit-test 11a: Re-attach DR, BH magnets Re-attach QW fixtures Vacuum work LCW Hook-ups A1 EPICS controls	Cable Tray Lowering Vacuum+Valve work LCW Hook-ups HV patch box remount Laser box install Prebuncher bracket removal	Rapid Access probe Air Manifold Install VIP2I00 T/S Valve controls Finishing laser box install Laser hut work	9a: Viewer/valve Solenoid Layout Remove PIG De-gas stalk heater Prebuncher LCW and Cabling Valve controls LCW Interlock Checkout	Valve controls Viewer reconnects LCW Hook-ups Laser box sealing	Sa	9a: Magnet Hook-Ups 60Hz Snooping
Tunnel Afternoon	Vacuum Work Laser Hut Work	Magnet Hook-Ups Laser Hut Work	De-gas stalk heater Gun HV Eval Preps Magnet Hook-Ups Laser Hut Work 430p: Lock-up to Power Permit Gun HV Eval	Magnet Hook-Ups Laser Hut Work 4p: Neilson WalkThru 430p: Lock-up to Power Permit Gun HV Eval	Magnet Hook-Ups Laser Hut Work	Sa	Magnet Hook-Ups 60Hz Snooping

4/16: Weekend work plans in the Injector?

• BPM = Francis
• Valve Controls = Ketchum
• ItoV, Picoammeters, Gun FSD Interlocks = Francis
• Viewers = Norris
• Harps = Dela Cruz
• Magnet / DC Power = Coleman, others in group
• 2B Alignment = S&A, Gould
• PSS = Kowal

Week 29 (Apr 19 - Apr 23)

Phase 1 - HCO & Commissioning

Tunnel work

• System Reconnects and HCO

• Laser->photocathode alignment, retro-reflection measurement (Zhang, Grames, Windham)

• Vacuum work (Stutzman)
  • T/S VIP2I00 noise
  • Relocating VCG5D01 to main beamline, ATLis 22270 (Stutzman) Tues
  • Pumping down 5D "stub" (i.e. remaining 5D beamline) (Stutzman) Tues

• Plumbing air lines to viewers (CIS, Norris)
• Air line system-segmentation (viewer, beamline valves) (Stutzman, Bullard)

• Magnet hook-ups (DC Power -- Coleman, Delk, Kumar) Afternoons
  • MDR1I02 attachment (Grames) Tues

• Diagnostics reconnects Mornings
  • Viewers (Norris)
  • Harps (Dela Cruz)
  • BPMs, Picoammeters, ItoV (Francis)

• LCW Flow measurement through flow meters that interlock cups and apertures (Francis) Mon
• PCup flowmeter enhanced testing (Francis)
• 2I BPM hook-ups (Francis) Tues

• LCW hook-ups (Adderley, Francis)

• Wien HV cable terminations (Dela Cruz)

• A1 EPICS controls (Windham, Higgins) Tues

• Warm RF Work (Wissman, Farrish)
  • Chopper, prebuncher, amplifier hook-ups Mon
  • Chopper water line leak repair Mon
  • LLRF testing and adjustments for prebuncher Tues
  • Powering on prebuncher, choppers W-F
  • Prebuncher tuning Wed
  • Chopper tuning

• Mech bracket walkthru (Gregory, Grames) Mon

• 60Hz electrical noise snooping (Suleiman) Evenings (after 4p)

• PSS Kicker removal (SSG) Thur
• Unlocking FC1, locking in A3/A4 apertures (SSG) Thur

• PCup-A1 Region (VBV1I07->0I02) & A2-FC1 Region (VBV0I02->0I07) Bake Prep
  • Remove PSS kicker, push back conduit (SSG)
  • Remove instrument solenoids from girders (Dela Cruz)
  • Move back non-bakable cables, air lines (CIS)
  • Staging insulation, oven equipment (Bullard)
  • Leak checks (Stutzman)
  • Ion pump evaluations
  • Gasket swaps Fri

ISB Work

• System re-connects / associated rack work
• A1 EPICS controls work (Windham, Higgins)
• iocin1 VME crate swap, IN03B04 (Dela Cruz), Mon 9a
• Wien HV System, IN01B0{0,1} (Dela Cruz)
• Safety WalkThru (Moser, Fanning, Johnson, Williams) Tues 230p
• Magnet Cabling, IN02B{10,11,22,26}, IN04B10 (DC Power, Coleman)
• Bunchlength amp re-install, IN02B23 (Musson)

Injector Tunnel and Service Building

Location Time	Mon 4/19	Tue 4/20	Wed 4/21	Thu 4/22	Fri 4/23
InjSB All Day	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	System Reconnects CIS Rack Work	System ~Reconnects CIS Rack Work	System ~Reconnects CIS Rack Work
InjSB Early Morning (<9a)	Associated Rack Work	Associated Rack Work	Associated Rack Work	Wien HV System	Wien HV System
InjSB Morning	Associated Rack Work	9a: iocin1 VME Crate Swap Wien HV Cable Termination Prebuncher LLRF Associated Rack Work	Wien HV Cable Terminations Associated Rack Work	Wien HV System Warm RF Cabling	Wien HV System Bunchlength amp re-install
InjSB Afternoon	Associated Rack Work	Prebuncher LLRF Associated Rack Work	Associated Rack Work	Magnet Cabling	Magnet Cabling
Tunnel All Day	CIS Vacuum Work -- VBV2I01A Solenoid	CIS Vacuum Work -- *Relocating VCG5D01 *5D stub pumpdown	CIS Vacuum Work -- *Valving in CCG to main beamline	VBV1I07->0I07 Leak Checks Bake Prep	PCup-A1 / A2-FC1 regions Bake Prep - Gasket Swaps
Tunnel Early Morning (<9a)	Viewer Reconnects	Viewer Reconnects PCup Flowmeter	Viewer Reconnects Wien HV cable terminations?	Wien HV cable terminations	Wien HV cable terminations
Tunnel Morning	915a Mech Bracket Walkthru 2I BPM Connections Viewer air lines Flowmeter flow measurement	Viewer Reconnects 2I BPM Hook-ups Air line system segmentation	Viewer Reconnects Wien HV cable terminations? Air line system segmentation Prebuncher Tuning/Controls Laser hut work	Leak Checks VBV2I01A T/S, Repair Unlock FC1, Lock-In A3/A4 Bake Prep: PSS Kicker Removal Instrument Solenoid Dismounts Oven/insulation staging	Bake Prep - Gasket Swaps
Tunnel Afternoon	Magnet hook-ups Laser Hut Work	Magnet hook-ups A1 EPICS Controls 230p: Safety WalkThru Laser Hut Work	MDR1I02 attachment 2p: Laser->cathode alignment Vacuum Recovery	Bake Prep Prebuncher testing/tuning 5D-VCG cabling	Bake prep - Gasket Swaps

WEEKEND WORK PLANS??

Tunnel Personnel Loading Limits: Injector, upstream of plastic curtain, total=8 -> 4 upstream of laser hut, 4 downstream of laser hut

Week 30 (Apr 26 - Apr 30)

Phase 1 - HCO & Commissioning

Tunnel work

• Re-Bake Work
  • As-found surveys of A1, A2 (S&A) Mon
  • Continue ion pump evaluations
  • Vent VBV1I07->0I07 and swap gaskets Mon
    • Decided NOT to swap A2 gaskets at this time
  • Re-align A1 (S&A) Mon
  • Rough pumpdown of VBV1I07->0I02 region (A1-region) Mon
  • Leak checks VBV1I07->0I07 Mon/Tues
  • Bake setup Tues-Wed
  • Begin A1-region (VBV1I07->0I02) re-bake Wed+
  • NEG activations --
    • Unbaked region, A2 (0I02) and 0I07 DP Can Tues
    • Baked A1-region, 0I00 DP Can and A1 (0I01A)

• VBV2I01A Position Indication and Solenoid T/S, Documentation, Verification (Windham) Mon

• Laser->photocathode alignment, retro-reflection measurement (Zhang, Grames, Windham) Tues

• Wien HV cable terminations (Dela Cruz)

• Viewer reconnects and HCO (Norris)

• Magnet Connections and HCO (Coleman)
  • Layout terminal blocks
  • Magnet lead reinforcement
  • Magnet wiring
  • Install MDR1I02 (CIS, Grames)

• Warm RF Work (Wissman, Farrish)
  • Prebuncher conditioning
  • Prebuncher readback calibrations
  • Chopper tune-check/tuning

• 60Hz electrical noise snooping (Suleiman) Evenings (after 4p)

• System re-connects and HCO (EES, CIS, Ops)

ISB Work

• System re-connects / associated rack work
• CIS Rack Work, IN01* (Windham)
• Viewer Terminations, IN01B04 (Norris, Mock) Mon-Tues
• Harp cabling, terminations, IN01B03, IN03B0{6,7} (Dela Cruz) Tues
• Magnet Cabling, IN02B{10,11,22,26}, IN04B10 (DC Power, Coleman)
• Wien HV System, IN01B0{0,1} (Dela Cruz)

Injector Tunnel and Service Building

Location Time	Mon 4/26	Tue 4/27	Wed 4/28	Thu 4/29	Fri 4/30	Sat 5/1	Sun 5/2
InjSB All Day	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work
InjSB Early Morning <9a	Viewer Terminations	Viewer Terminations Harp Cabling/Terminations	Associated Rack Work	Associated Rack Work	Associated Rack Work
InjSB Morning	Viewer Terminations	Viewer Terminations Harp Cabling/Terminations	Associated Rack Work	Associated Rack Work	Associated Rack Work	Chopper Hook-Ups
InjSB Afternoon	Magnet Cabling, HCO	Magnet Cabling, HCO	Magnet Cabling, HCO	Magnet Cabling, HCO	Magnet Cabling, HCO		Magnet Cabling, HCO
Tunnel All Day	A1/A2 gasket swaps	VBV1I07->0I02 = A1-region Bake Setup	A1-region Re-Bake	A1-region Re-Bake	A1-region Re-Bake	A1-region Re-Bake Rampdown	A1-region Re-Bake Rampdown
Tunnel Early Morning <9a	As-found surveys A1, A2 Diagnostics HCO/Reconnects as possible Wien HV Cable Terminations	Diagnostics HCO/Reconnects as possible 0I02 Anti-collision/harp	Viewer Reconnects Wien HV terminations	Viewer Reconnects Wien HV terminations	Viewer Reconnects 7-8a: LCW Tests
Tunnel Morning	A1 Gasket Swaps Re-Alignment Rough Pumpdown Wien HV Cable Terminations Ion pump checkout VBV2I01A Work	Final A1-region leak check VIP0I0{0,1,1A,2} FE Hunt A1-region Bake Setup 0I02 NEG Activation Prebuncher conditioning	930-10a: Hoey Safety WalkThru Viewer Reconnects Wien HV terminations Prebuncher conditioning Cable Org/Vert Tray	Viewer Reconnects Prebuncher conditioning	Viewer Reconnects Prebuncher conditioning 0I07 NEG Activation	0I0{0,1A} NEG Activations Chopper Hook-Ups	11a: Magnet reconnects and HCO
Tunnel Afternoon	A1 rough pumpdown Leak checks VBV1I07->0I07 VBV2I01A Work	Begin A1-region Bake Laser alignment/retroreflection Prebuncher conditioning < ~2p Magnet HCO/Reconnects as possible	Prebuncher conditioning Cable Org/Vert Tray Magnet HCO/Reconnects as possible Laser Hut Work	1p: PD WalkThru Prebuncher conditioning Magnet HCO/Reconnects as possible Laser Hut Work	Prebuncher Conditioning Magnet HCO/Reconnects as possible Laser Hut Work		Magnet reconnects and HCO

Tunnel Personnel Loading Limits: Injector, upstream of plastic curtain, total=8 -> 4 upstream of laser hut, 4 downstream of laser hut

Week 31 (May 3 - May 7)

Phase 1 - HCO & Commissioning

Tunnel work

• System re-connects and HCO (EES, CIS, Ops)

• A1-region bake takedown (Stutzman, Bullard)
• VBV2I01A Solenoid Air Leak T/S (Windham)
• Laser hut work (Zhang)
• Photocathode shuffle (Grames)
  • Remove bulk GaAs
  • Load in SSL cathodes
  • Activate cathode

• Main airline leaky valve swap (pics) (MechInstall) Thurs or Fri

• Viewer reconnects and HCO (Norris)
• Harp reconnects and HCO (Dela Cruz)

• Magnet Connections and HCO (Coleman)
  • Layout terminal blocks
  • Magnet lead reinforcement
  • Magnet wiring
  • Install MDR1I02 (CIS, Grames)

• Warm RF HCO (Wissman, Farrish)
  • Chopper turn-on, conditioning
  • Buncher turn-on, conditioning
  • Capture turn-on, conditioning

• 60Hz electrical noise snooping (Suleiman) Evenings (after 4p)

ISB Work

• System re-connects / associated rack work
• CIS Rack Work, IN01* (Windham)
• Magnet Cabling, IN02B{10,11,22,26}, IN04B10 (DC Power, Coleman)
• Wien HV System, IN01B0{0,1} (Dela Cruz)
• Penetration 78 (IN02B18) and 86 (IN02B23) Stone Top-Off (MechInstall) Tues early AM

Injector Tunnel and Service Building

Location Time	Mon 5/3	Tue 5/4	Wed 5/5	Thu 5/6	Fri 5/7	Sa 5/8	Su 5/9
InjSB All Day	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work	Systems HCO CIS Rack Work
InjSB Early Morning <9a	Associated Rack Work	Chopper/Buncher HCO	Chopper/Buncher HCO	Buncher/Chopper HCO	Buncher/Chopper HCO
InjSB Morning	Chopper/Buncher HCO Prebuncher Rdbk Cals	Chopper/Buncher HCO Wien Sys Walkthru Pene 78 & 86 Top-Off	Chopper/Buncher HCO Wien HV Cable Chkout	Buncher/Chopper HCO	Buncher/Chopper HCO
InjSB Afternoon	Chopper/Buncher HCO Prebuncher Rdbk Cals Magnet re-connects, HCO	Chopper/Buncher HCO Magnet re-connects, HCO	Chopper/Buncher HCO Magnet re-connects, HCO	Magnet re-connects, HCO Swings: Capture HCO, Conditioning	Magnet re-connects, HCO Swings: Capture HCO, Conditioning
Tunnel All Day	CIS Reconnects A1-region Bake Takedown	CIS Vacuum Work Ion pump checkout VIP0I01/1A HiPot Device/line labeling Other CIS Jobs PCup, A1, A2 LCW PCup, A1 Current Pigtails Photocathode shuffle	System Reconnects & HCO	System Reconnects & HCO	System Reconnects & HCO
Tunnel Early Morning <9a	Viewers (1 ppl) (away from A1) A1-region bake takedown	Viewers (1 ppl) Wien Interlock Cables (1 ppl) CIS Jobs (1-2 ppl)	Viewers (1 ppl) Harp / Wien (1 ppl) BPM (1 ppl) Buncher, Capture hook-ups (1 ppl)	Main Airline Valve Swap Viewers (1 ppl) Harp / Wien (1ppl) BPM (1 ppl)	Main Airline Valve Swap Viewers (1 ppl) Harp (1ppl) Waterflow Interlocks (1ppl)
Tunnel Morning	Viewers (1 ppl) (away from A1) A1-region Leak Checks	Viewers (1 ppl) 11-1130a: Wien Sys Walkthru (2 ppl) CIS Vac Work (1-2 ppl)	Viewers (1 ppl) 9a-noon: Wien HV Cable Chkout (2ppl) BPM (1 ppl)	Viewers (1 ppl) Harp / Wien (1ppl) BPM (1 ppl)	Viewers (1 ppl) Harp (1ppl) ItoV Checks (1 ppl)
Tunnel Afternoon	A1-region reattachments -- air/water lines, pickups, control boxes/solenoids	Magnet (2-4 ppl)	Magnet (2-4 ppl) Swings (4p): Lock-up, 0L02 HPA PSS Cert After: PSS Kicker Install	Magnet (2-4 ppl) Swings (4p): Lock-up, PSS Certs or Capture HCO	Magnet (2-4 ppl) Swings (4p): Capture HCO

Tunnel Personnel Loading Limits: Injector, upstream of plastic curtain, total=8 -> 4 upstream of laser hut, 4 downstream of laser hut

Points of Contact by system --

• BPM = Francis
• Valve Controls = Ketchum
• ItoV, Picoammeters, Gun FSD Interlocks = Francis
• Viewers = Norris
• Harps = Dela Cruz
• Wien = Dela Cruz
• Magnet / DC Power = Coleman
• Warm RF -- prebuncher, buncher, chopper, capture = Wissman
• 2B Alignment = S&A, Gould
• PSS = Kowal

Week 32 (May 10 - May 14)

Phase 1 - HCO & Commissioning

Tunnel work

ISB Work

Location Time	Mon 5/10	Tue 5/11	Wed 5/12	Thu 5/13	Fri 5/14	Sa 5/15	Su 5/16
InjSB All Day
InjSB Early Morning <9a
InjSB Morning
InjSB Afternoon
Tunnel All Day	2B Alignment	2B Alignment float
Tunnel Early Morning <9a
Tunnel Morning
Tunnel Afternoon

Tunnel Personnel Loading Limits: Injector, upstream of plastic curtain, total=8 -> 4 upstream of laser hut, 4 downstream of laser hut

Penetration Work

4/9 Update:
All five penetrations that had been opened are now closed, sealed, and appropriate stone/Pb-brick shielding returned. {58, 86, 108, 135} - re-filled with stone and levels verified by RadCon. Laser hut penetration closed, sealed, and Pb brick shielding re-installed.

4/2 Update:
Laser hut penetration remains open until conclusion of Wien/Y-chamber bake, early next week. (only gets closed and sealed, no stone)
58, 86, and 108 closed and sealed. May be filled with stones at this point.
135 remains open. To be closed, sealed, and filled next week.

InjSB Penetrations that are open (click for pictures, last updated 2/18/21): above laser hut, 58, 86, 108, 135

• 34ft from floor of InjSB to floor of Inj tunnel
• 25ft from floor of InjSB to elevated Inj tunnel cable tray

Penetration Cable Pulls/Removals --

• (C. Jones) Dehumidifier wire pull, penetration 135, ETA: end of week of 3/1
• (Wissman) Pulling Prebuncher heater control cables, laser hut penetration, ETA: ~3/4 or 5
• (FML) Add/pull flex conduit to laser hut, 86, and 108 penetrations
  • 86 and 108 too full for 2" flex pull
  • Laser hut deemed too full as well
• (Dela Cruz) Pulling new Wien E-field HV cables, through flex conduit, laser hut penetration may be re-filled
• Norris removing old Cat5 viewer cables
• Norris pulling new viewer cables
• Riad/Scott removing old Mott HV cables
• Coleman pulling new Wien B-field magnet cables
• Cole pulling new neutron detector cables (above 0L03)
• Scott pulling motor control cables for A1++

Fire System Work

Description of Task: Replacement of tunnel sprinkler piping, fire alarm control panels in B85 & B98, replacement of detection devices.

update 11/9: 25% of demo completed
update 11/23: demo completed
update 12/8: fire pipe installation in Injector slated for Winter break ~12/21 - 1/3
"The drawings needed prior to fabrication of the INJ fire pipe have not gone through the system." No fire pipe install work over winter break.
update 1/7/21: Tentative fire pipe install to occur week of 1/18 in tunnel. Should take 3-4 days, so with the holiday on Monday, likely the rest of the week.
Further fire pipe work upstairs in the service will also need 3-4 days, but won't be constant (i.e. contractor will be in and out).
update 1/18/21: New pipe arriving Fri 1/22. No install work week of 1/18.
update 1/20/21: fire pipe installation to begin 1/22 and continue over weekend 1/23+24.
update 2/1/21: fire pipe installation, air pressure and hydro tests complete.