Difference between revisions of "Injector Solenoids Upgrade"

From Ciswikidb
Jump to navigation Jump to search
Line 1: Line 1:
 
== Injector Solenoids - Review ==
 
== Injector Solenoids - Review ==
 +
 +
;Introduction
 +
A variety of solenoid magnets have been in use at the CEBAF injector for over 20 years.  A total of 11 individual solenoids are installed, spanning 7 different types (FH,FB,FG,FQ,FA,FD,FL).  In order to preserve the beam polarization four of the type two internal counter-wound coils (FQ,FA,FD,FL) while others have a single internal coil (FH,FB,FG).  A summary of the 11 coils is listed below and can found on the injector songsheet [[media:190605_injectorsongsheet.pdf]].
 +
 +
MFH2I01 - beam line solenoid, single wound
 +
MFB1I02 - beam line solenoid, single wound
 +
MFG1I04A - beam line solenoid, single wound
 +
MFG1I04B - beam line solenoid, single wound
 +
MFQ0I01 - beam line solenoid, counter wound
 +
MFA0I03 - beam line solenoid, counter wound
 +
MFD0I04 - two chopper solenoids in series, each counter wound
 +
MFA0I05 - beam line solenoid, counter wound
 +
MFA0I06 - beam line solenoid, counter wound
 +
MFL0I07 - beam line solenoid, counter wound
 +
 +
While the magnets work reliably, there is an initiative to replace these solenoids with new magnets so the following is achieved:
 +
a) fewest types possible, to improve standardization and spares inventory
 +
b) greater radial field uniformity, to minimize variation of beam optics with beam position
 +
c) minimum field roll-off in the beam direction
 +
d) design accommodating operation at higher beam energy, i.e. function at higher power supply current
 +
e) larger inner diameter to accommodate 2-3/4" flanges
 +
f) bakable to >200C for extended periods for vacuum condition
 +
g) capability to be interchangeably wired for single wound or counter wound configuration
 +
 +
With these considerations in mind Jay Benesh and Danny Machie have developed a solenoid magnet, in three variations, that will improve functionality.  The purpose of this review the proposed specifications and drawings that would be provided for a vendor RFQ and provide feedback or questions that would help us better clarify or improve the request.
  
 
;Materials to be supplied for RFQ
 
;Materials to be supplied for RFQ

Revision as of 14:38, 5 June 2019

Injector Solenoids - Review

Introduction

A variety of solenoid magnets have been in use at the CEBAF injector for over 20 years. A total of 11 individual solenoids are installed, spanning 7 different types (FH,FB,FG,FQ,FA,FD,FL). In order to preserve the beam polarization four of the type two internal counter-wound coils (FQ,FA,FD,FL) while others have a single internal coil (FH,FB,FG). A summary of the 11 coils is listed below and can found on the injector songsheet media:190605_injectorsongsheet.pdf.

MFH2I01 - beam line solenoid, single wound MFB1I02 - beam line solenoid, single wound MFG1I04A - beam line solenoid, single wound MFG1I04B - beam line solenoid, single wound MFQ0I01 - beam line solenoid, counter wound MFA0I03 - beam line solenoid, counter wound MFD0I04 - two chopper solenoids in series, each counter wound MFA0I05 - beam line solenoid, counter wound MFA0I06 - beam line solenoid, counter wound MFL0I07 - beam line solenoid, counter wound

While the magnets work reliably, there is an initiative to replace these solenoids with new magnets so the following is achieved: a) fewest types possible, to improve standardization and spares inventory b) greater radial field uniformity, to minimize variation of beam optics with beam position c) minimum field roll-off in the beam direction d) design accommodating operation at higher beam energy, i.e. function at higher power supply current e) larger inner diameter to accommodate 2-3/4" flanges f) bakable to >200C for extended periods for vacuum condition g) capability to be interchangeably wired for single wound or counter wound configuration

With these considerations in mind Jay Benesh and Danny Machie have developed a solenoid magnet, in three variations, that will improve functionality. The purpose of this review the proposed specifications and drawings that would be provided for a vendor RFQ and provide feedback or questions that would help us better clarify or improve the request.

Materials to be supplied for RFQ
Vendor List
Everson-Tesla Inc., Doug Hartman (dhartman@eversontesla.com)
Supplemental Material
Retrieved from "https://wiki.jlab.org/ciswiki/index.php?title=Injector_Solenoids_Upgrade&oldid=17728"