Difference between revisions of "Injector Solenoids Upgrade"

From Ciswikidb
Jump to: navigation, search
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
== Injector Solenoids - Review ==
 
== Injector Solenoids - Review ==
  
;Introduction
+
===Introduction===
 
A variety of solenoid magnets have been in use at the CEBAF injector for over 20 years.  A total of 11 individual solenoids are installed, spanning 7 different types (FH,FB,FG,FQ,FA,FD,FL).  In order to preserve the beam polarization four of the type two internal counter-wound coils (FQ,FA,FD,FL) while others have a single internal coil (FH,FB,FG).  A summary of the 11 coils is listed below and can found on the injector songsheet [[media:190605_injectorsongsheet.pdf]].
 
A variety of solenoid magnets have been in use at the CEBAF injector for over 20 years.  A total of 11 individual solenoids are installed, spanning 7 different types (FH,FB,FG,FQ,FA,FD,FL).  In order to preserve the beam polarization four of the type two internal counter-wound coils (FQ,FA,FD,FL) while others have a single internal coil (FH,FB,FG).  A summary of the 11 coils is listed below and can found on the injector songsheet [[media:190605_injectorsongsheet.pdf]].
  
MFH2I01 - beam line solenoid, single wound
+
*MFH2I01 - beam line solenoid, single wound
MFB1I02 - beam line solenoid, single wound
+
*MFB1I02 - beam line solenoid, single wound
MFG1I04A - beam line solenoid, single wound
+
*MFG1I04A - beam line solenoid, single wound
MFG1I04B - beam line solenoid, single wound
+
*MFG1I04B - beam line solenoid, single wound
MFQ0I01 - beam line solenoid, counter wound
+
*MFQ0I01 - beam line solenoid, counter wound
MFA0I03 - beam line solenoid, counter wound
+
*MFA0I03 - beam line solenoid, counter wound
MFD0I04 - two chopper solenoids in series, each counter wound
+
*MFD0I04 - two chopper solenoids in series, each counter wound
MFA0I05 - beam line solenoid, counter wound
+
*MFA0I05 - beam line solenoid, counter wound
MFA0I06 - beam line solenoid, counter wound
+
*MFA0I06 - beam line solenoid, counter wound
MFL0I07 - beam line solenoid, counter wound
+
*MFL0I07 - beam line solenoid, counter wound
  
 
While the magnets work reliably, there is an initiative to replace these solenoids with new magnets so the following is achieved:
 
While the magnets work reliably, there is an initiative to replace these solenoids with new magnets so the following is achieved:
a) fewest types possible, to improve standardization and spares inventory
+
# fewest types possible, to improve standardization and spares inventory
b) greater radial field uniformity, to minimize variation of beam optics with beam position
+
# greater radial field uniformity, to minimize variation of beam optics with beam position
c) minimum field roll-off in the beam direction
+
# minimum field roll-off in the beam direction
d) design accommodating operation at higher beam energy, i.e. function at higher power supply current
+
# design accommodating operation at higher beam energy, i.e. function at higher power supply current
e) larger inner diameter to accommodate 2-3/4" flanges
+
# larger inner diameter to accommodate 2-3/4" flanges
f) bakable to >200C for extended periods for vacuum condition  
+
# bakable to >200C for extended periods for vacuum condition  
g) capability to be interchangeably wired for single wound or counter wound configuration
+
# capability to be interchangeably wired for single wound or counter wound configuration
  
With these considerations in mind Jay Benesh and Danny Machie have developed a solenoid magnet, in three variations, that will improve functionality.  The purpose of this review the proposed specifications and drawings that would be provided for a vendor RFQ and provide feedback or questions that would help us better clarify or improve the request.
+
With these considerations in mind Jay Benesh has modeled an upgrade solenoid magnet and worked with Danny Machie to develop a mechanical design, in three variations, that have been reviewed by the injector and source groups'''The purpose of your review is to inspect the proposed specifications and drawings tand provide feedback or questions that should be incorporated prior to starting the vendor RFQ process.'''  Supplemental material of a design study of different variations on the inner diameter is also provided here [[media:design_comp.pdf]].
  
;Materials to be supplied for RFQ
+
===Reviewers===
 +
* Joe Meyers, Magnet Measurement Facility (will handle the RFQ and acceptance QA too)
 +
* Michael Tiefenback, CEBAF Magnet Integrator
 +
* Renuka Rajput-Ghoshal, Physics Engineering Magnet Group
 +
 
 +
===RFQ Package===
 
* Specification to vendor - [[media:magnet_spec.pdf]] or [[media:magnet_spec.odt]]
 
* Specification to vendor - [[media:magnet_spec.pdf]] or [[media:magnet_spec.odt]]
 
* Coil drawing - [[media:coil8may19.pdf]]
 
* Coil drawing - [[media:coil8may19.pdf]]
* Low Momentum Solenoid (200 keV beam line) - [[media:lowmomentumbeamlinesketch5.pdf]]
+
* Low Momentum Solenoid (replaces FH, FB, FA, FL beam line magnets) - [[media:lowmomentumbeamlinesketch5.pdf]]
* Low Momentum Solenoid (200 keV chopper) - [[media:lowmomentumchoppersketch2.pdf]]
+
* Low Momentum Solenoid (replaces FD chopper magnets) - [[media:lowmomentumchoppersketch2.pdf]]
* Low Momentum Solenoid (200 keV beam line) - [[media:highmomentumbeamlinesketch4.pdf]]
+
* High Momentum Solenoid (proposed new solenoid for MeV beam energies) - [[media:highmomentumbeamlinesketch4.pdf]]
 
+
;Vendor List
+
: Everson-Tesla Inc., Doug Hartman (dhartman@eversontesla.com)
+
  
;Supplemental Material
+
===Possible Vendor List===
* Optics assessment of keV solenoids of different ID [[media:design_comp.pdf]]
+
* New Zealand company that did Jay's initial quote
 +
* Everson-Tesla Inc., Doug Hartman (dhartman@eversontesla.com)
 +
* Alpha
 +
* New England Technicoil
 +
* Alexandria, Va company Joe met at ILC meeting

Revision as of 08:56, 24 October 2019

Injector Solenoids - Review

Introduction

A variety of solenoid magnets have been in use at the CEBAF injector for over 20 years. A total of 11 individual solenoids are installed, spanning 7 different types (FH,FB,FG,FQ,FA,FD,FL). In order to preserve the beam polarization four of the type two internal counter-wound coils (FQ,FA,FD,FL) while others have a single internal coil (FH,FB,FG). A summary of the 11 coils is listed below and can found on the injector songsheet media:190605_injectorsongsheet.pdf.

  • MFH2I01 - beam line solenoid, single wound
  • MFB1I02 - beam line solenoid, single wound
  • MFG1I04A - beam line solenoid, single wound
  • MFG1I04B - beam line solenoid, single wound
  • MFQ0I01 - beam line solenoid, counter wound
  • MFA0I03 - beam line solenoid, counter wound
  • MFD0I04 - two chopper solenoids in series, each counter wound
  • MFA0I05 - beam line solenoid, counter wound
  • MFA0I06 - beam line solenoid, counter wound
  • MFL0I07 - beam line solenoid, counter wound

While the magnets work reliably, there is an initiative to replace these solenoids with new magnets so the following is achieved:

  1. fewest types possible, to improve standardization and spares inventory
  2. greater radial field uniformity, to minimize variation of beam optics with beam position
  3. minimum field roll-off in the beam direction
  4. design accommodating operation at higher beam energy, i.e. function at higher power supply current
  5. larger inner diameter to accommodate 2-3/4" flanges
  6. bakable to >200C for extended periods for vacuum condition
  7. capability to be interchangeably wired for single wound or counter wound configuration

With these considerations in mind Jay Benesh has modeled an upgrade solenoid magnet and worked with Danny Machie to develop a mechanical design, in three variations, that have been reviewed by the injector and source groups. The purpose of your review is to inspect the proposed specifications and drawings tand provide feedback or questions that should be incorporated prior to starting the vendor RFQ process. Supplemental material of a design study of different variations on the inner diameter is also provided here media:design_comp.pdf.

Reviewers

  • Joe Meyers, Magnet Measurement Facility (will handle the RFQ and acceptance QA too)
  • Michael Tiefenback, CEBAF Magnet Integrator
  • Renuka Rajput-Ghoshal, Physics Engineering Magnet Group

RFQ Package

Possible Vendor List

  • New Zealand company that did Jay's initial quote
  • Everson-Tesla Inc., Doug Hartman (dhartman@eversontesla.com)
  • Alpha
  • New England Technicoil
  • Alexandria, Va company Joe met at ILC meeting