Difference between revisions of "Meeting 9/21/22 - COMTRA"
Jump to navigation
Jump to search
(Created page with ";Thursday's @ 9am EDT by Zoom * Join ZoomGov Meeting - https://jlab-org.zoomgov.com/j/1601906056?pwd=V2xxUjJhQWN3RC91M2ZBOUVrbmhnUT09 * Zoom ID: 160 190 6056 and Passcode: 992...") |
|||
| Line 8: | Line 8: | ||
* ME/Layout | * ME/Layout | ||
| − | ** | + | ** Mike/Eric completed quick reference => ME can use to populate songsheet |
| − | ** | + | ** Matt working with SCMB & RadCon (100 nA shielded hut, 25 nA unshielded hut) |
| − | |||
* Experiment components | * Experiment components | ||
| − | ** collimator installed and aligned | + | ** collimator installed and aligned => |
** magnet measurement, status for install | ** magnet measurement, status for install | ||
| − | ** detector assembly, fiducialization | + | ** detector assembly, fiducialization => walkthrough completed wit |
* I&C jobs | * I&C jobs | ||
| − | ** Remote motion control for aperture (otherwise do by hand w/ access) | + | ** Remote motion control for aperture (otherwise do by hand w/ access) => done |
| − | ** Attach current monitors to aperture and dump | + | ** Attach current monitors to aperture and dump => done |
| − | ** Plumb LCW for current monitor and dump | + | ** Plumb LCW for current monitor and dump => done 0.75 gpm, SSG update FSD text |
| − | ** Pull 6 fibers from DAQ to mezzanine | + | ** Pull 6 fibers from DAQ to mezzanine => not yet |
| − | ** Align x-ray camera for x-ray card after collimator | + | ** Align x-ray camera for x-ray card after collimator => ? |
| + | ** Insertable 1/2-waveplate | ||
| + | ** pull Heliax to gun rack => done, cable #10 | ||
* DAQ/Controls | * DAQ/Controls | ||
Revision as of 20:55, 21 September 2022
- Thursday's @ 9am EDT by Zoom
- Join ZoomGov Meeting - https://jlab-org.zoomgov.com/j/1601906056?pwd=V2xxUjJhQWN3RC91M2ZBOUVrbmhnUT09
- Zoom ID: 160 190 6056 and Passcode: 992019
Readiness Updates
- Tour of installation so far media:220914_COMTRA.pptx
- ME/Layout
- Mike/Eric completed quick reference => ME can use to populate songsheet
- Matt working with SCMB & RadCon (100 nA shielded hut, 25 nA unshielded hut)
- Experiment components
- collimator installed and aligned =>
- magnet measurement, status for install
- detector assembly, fiducialization => walkthrough completed wit
- I&C jobs
- Remote motion control for aperture (otherwise do by hand w/ access) => done
- Attach current monitors to aperture and dump => done
- Plumb LCW for current monitor and dump => done 0.75 gpm, SSG update FSD text
- Pull 6 fibers from DAQ to mezzanine => not yet
- Align x-ray camera for x-ray card after collimator => ?
- Insertable 1/2-waveplate
- pull Heliax to gun rack => done, cable #10
- DAQ/Controls
- Helicity generator
- High Voltage
- EFADC/DAQ
- Kepco PS
- Experiment sequence
- Pre-Beam - complete HCO, magnet ready, assembly detector ready, fiducial them, mock-up install ?, remove temporarily
- Commission - setup beam to FCUP, APERTURE, DUMP and use x-ray card to define orbit to collimator
- Experiment - install/align magnet/detector (w/ attenuators?), deliver x-rays, optimize DAQ, measure asymmetry vs. XYZ and with Wien
Older Links
- UITFList Links
- General COMTRA installation => https://tasklists.jlab.org/uitflist/tasks/107371
- DC power magnet install => https://tasklists.jlab.org/uitflist/tasks/107370
- Beamline
- Layout for RadCon media:Compton Layout for Radcon Shielding 8-10-22-3.pptx
- Spool flanges media:Flanges and Reducer for Compton and RF Kicker-jmg.xlsx
- Radiator - (1) on-hand, (1) need for BNL thumb
- Lead for UITF - (11) 2 X 4 X 4, (2) 2 X 4 X 6, (99) 2 X 4 X 8 thumb
- Magnet
- Kepco PS - ship 8/31 2 day air => PR
- Magnet EMC PR#1PR#2 coil thumb
- Detector
- Documentation
- NIM - Elsevier Article (elsarticle) template => https://www.overleaf.com/project/62bc9efe48a3a93aef37be0a
- Manual - Sharepoint