View source for To do list in preparation for water irradiation and final booster characterizations studies

[[media:to do list at UITF for water irradiation studies 7_7_21.docx]]

Engineering support jobs

keV region:
*[DC] Reconnect two steering magnet sets and solenoid on the NEG tube near the gun after the bakeout
*[IC] Restore operation of ITVK202 and ITVK203 (at the Wien, if it were there).  These channels were used for HDIce dump viewers ITVMA01A and B (might have names wrong)

MeV regions:
Near FCup3:
*[DC] Four corrector (2 sets) near dif pump station and FCup3, restore them: 
**MHBM401H/V between manual and fast valve – On beam line; requires connection
**MHBM501H/V over bellows in from in IPMM501 – requires mounting and connection
*[IC/VAC] Fast valve – Pull cable, interface locally and to VCG, mount electronics, and test
BCM + Current clamp receiver/chassis from Musson/Seaton
*[IC/VAC] Power + Cable NEG VGPM401 on cross with VIPM401 [Software] Controls
*[IC] ITVM401 connections, restore them. [software] Viewer is now a YAG.
*[IC] FCup3 connections, restore them
*[IC/VAC] VBVM501 connections, restore them
*[LLRF] Yao cavity – Prototype receiver install + cable from LLRF [Software/LLRF] Controls
*[Experiment] Place shielding around FC3 region

Spectrometer line:
[IC] IHAM703 was replaced, but need correct cable connections, verification it moves. Controls changes required for different harp style? If so - [software]
[IC/VAC] Power + Cable NEG added in front of IHAM703

New straight ahead line to water samples:
[IC/VAC] New valve VBVM602 – verify operation / hook up
Three new BPMs: IPMM602, IPMM603, and IPMM604
•	[IC] Verify connections and operation
•	[Software] Controls changes – Kyle working it already.
[DC] 3 new steering magnet sets: Verify & Polarity check installation. Update CED as appropriate.
•	MHBM602AH/V: ITF07 Channel 11/12 rerouted
•	MHBM602BH/V: ITF07 Channel 14 rerouted to vertical; Ch. 13 still needs rerouting to horizontal
•	MHBM603H/V: ITF07 Ch 17/18 rerouted
Also, secure loose magnet cables on that rack.
Solenoid –
•	[Install] Plumb LCW / Flow meter (from DC)
•	[DC] Power Supply, Cabling, Integration
•	[Software] EPICs contol 
[IC] 2 new viewers: ITVM603 and ITVM604 – both YAG. Connect & interface.
[IC] FCup4 in/out
[IC] Video only channel at water sample area (Norris hooking up with Hannes Tuesday.)
Stepper motor controlled sample holder (Windham + Lu) – Mount after 80/20 table build [Experiment] and integrate
[Experiment] Build 80/20 shielding Table
[IC/Vacuum] Power + Cable NEG (x2): VGPM603 on cross with VIPM603. VGPM604 on cross with VIPM604A
[IC/Vacuum] VCGM604 Cathode Gauge – Cable, power, interface to EPICS 
[Experiment] Place Decarad heads
[Experiment] Mount fluorescing screen after target

Safety System Group:
Relocate BLMs
Update gold masking
FSD for BCM Current clamp; from [IC]
FSD for Solenoid for [DC]

[ME] Design related:
Plate and 2”x2” support leg at FCup3
Camera holders: 2.75” and 4.625” flanges
Table for water sample holder (pictures for assembly)

[All system owners] Other: CED updates and verification for everything