Difference between revisions of "DAQ in EEL 108"
| Line 1: | Line 1: | ||
How to run the DAQ in EEL building room 108. | How to run the DAQ in EEL building room 108. | ||
| + | |||
| + | Updated Jan 24, 2023. Bob Michaels. | ||
Three VXS crates each with 15 FADCs. So, that is 720 channels of FADC. | Three VXS crates each with 15 FADCs. So, that is 720 channels of FADC. | ||
| Line 7: | Line 9: | ||
Start/stop runs | Start/stop runs | ||
| − | Usually the DAQ is already running one of the workspaces on cdaql3 (giant screen). Then it's like any other CODA system. Stop/start runs with the Run Control GUI (rcgui). | + | Usually the DAQ is already running on one of the workspaces on cdaql3 (the giant screen). Then it's like any other CODA system. Stop/start runs with the Run Control GUI (rcgui). |
How to CODA start from scratch. | How to CODA start from scratch. | ||
| − | On hccoda@cdaql3, type "startCoda" (note the capital C). The xterms with components pops up. Those are the 3 crates nps-vme1, nps-vme2, nps-vme3, as well as the event builder PEB1. The Run Control GUI (rcgui) pops up. We normally want the configuration "NPS_3crate" for the aforementioned crates. We also have single-VME configs ("vme1", "vme2", "vme3") but they only work if the trigger is plugged into the master TI. More on trigger below. | + | On hccoda@cdaql3, type "startCoda" (note the capital C). The xterms with components pops up. Those are the 3 crates nps-vme1, nps-vme2, nps-vme3, as well as the event builder PEB1. The Run Control GUI (rcgui) pops up. We normally want the configuration "NPS_3crate" for the aforementioned crates. We also have single-VME configs ("vme1", "vme2", "vme3") but they only work if the trigger is plugged into the master TI. More on the trigger below. |
| − | + | FADC parameters are defined in the usual config file | |
ssh -X nps-vme1 -l hccoda ; | ssh -X nps-vme1 -l hccoda ; | ||
| Line 21: | Line 23: | ||
Trigger | Trigger | ||
| − | Curently | + | Curently the trigger is a front-panel trigger going into the 7th input of the TI-master. This input is labelled "TS#1". Later we'll have a fancy VTP trigger and I'll update this. But currently the trigger consists of the "and" between a scintillator on top and bottom of the calorimeter. And each scintillator is the "or" of the two PMTs that are connected to the two ends of the scintillator. |
Revision as of 09:41, 24 January 2023
How to run the DAQ in EEL building room 108.
Updated Jan 24, 2023. Bob Michaels.
Three VXS crates each with 15 FADCs. So, that is 720 channels of FADC.
user: hccoda Password is posted near the screen computer: cdaql3
Start/stop runs
Usually the DAQ is already running on one of the workspaces on cdaql3 (the giant screen). Then it's like any other CODA system. Stop/start runs with the Run Control GUI (rcgui).
How to CODA start from scratch.
On hccoda@cdaql3, type "startCoda" (note the capital C). The xterms with components pops up. Those are the 3 crates nps-vme1, nps-vme2, nps-vme3, as well as the event builder PEB1. The Run Control GUI (rcgui) pops up. We normally want the configuration "NPS_3crate" for the aforementioned crates. We also have single-VME configs ("vme1", "vme2", "vme3") but they only work if the trigger is plugged into the master TI. More on the trigger below.
FADC parameters are defined in the usual config file
ssh -X nps-vme1 -l hccoda ; cd cfg ; and see nps-vmeN.cfg where N = 1, 2, 3. Please don't modify these unless you know what you are doing.
Trigger
Curently the trigger is a front-panel trigger going into the 7th input of the TI-master. This input is labelled "TS#1". Later we'll have a fancy VTP trigger and I'll update this. But currently the trigger consists of the "and" between a scintillator on top and bottom of the calorimeter. And each scintillator is the "or" of the two PMTs that are connected to the two ends of the scintillator.