Difference between revisions of "NPS VTP Serial Connection"
Jump to navigation
Jump to search
(Created page with "== uBoot boot interruption for configuration == * When the VME-VXS crate is power cycled, the display will show the uboot process. It can be interrupted during the count down...") |
|||
| Line 1: | Line 1: | ||
== uBoot boot interruption for configuration == | == uBoot boot interruption for configuration == | ||
| − | * When the VME-VXS crate is power cycled, the display will show the uboot process. | + | * When the VME-VXS crate is power cycled, the display will show the uboot process. |
| + | <pre> | ||
| + | Xilinx First Stage Boot Loader | ||
| + | Release 2015.4 Jan 30 2017-11:51:58 | ||
| + | Reset reason register 0x00000040 | ||
| + | [SWDT_RST] = 0, System Watchdog timer | ||
| + | [AWDT0_RST] = 0, CPU 0 Watch Timer | ||
| + | [AWDT1_RST] = 0, CPU 1 Watch Timer | ||
| + | [SLC_RST] = 0, Write to soft reset bit | ||
| + | [DBG_RST] = 0, Debug command DAP controller | ||
| + | [SRST_B] = 0, PS_SRST_B reset signal | ||
| + | [POR] = 1, PS_POR_B reset signal | ||
| + | reserved = 0, reserved | ||
| + | Devcfg driver initialized | ||
| + | Silicon Version 3.1 | ||
| + | Boot mode is SD | ||
| + | SD: rc= 0 | ||
| + | SD Init Done | ||
| + | Flash Base Address: 0xE0100000 | ||
| + | Reboot status register: 0x60400000 | ||
| + | Multiboot Register: 0x0000C000 | ||
| + | Image Start Address: 0x00000000 | ||
| + | Partition Header Offset:0x00000C80 | ||
| + | Partition Count: 2 | ||
| + | Partition Number: 1 | ||
| + | Header Dump | ||
| + | Image Word Len: 0x00015D85 | ||
| + | Data Word Len: 0x00015D85 | ||
| + | Partition Word Len:0x00015D85 | ||
| + | Load Addr: 0x04000000 | ||
| + | Exec Addr: 0x04000000 | ||
| + | Partition Start: 0x000065D0 | ||
| + | Partition Attr: 0x00000010 | ||
| + | Partition Checksum Offset: 0x00000000 | ||
| + | Section Count: 0x00000001 | ||
| + | Checksum: 0xF7FB7F3F | ||
| + | Application | ||
| + | Handoff Address: 0x04000000 | ||
| + | In FsblHookBeforeHandoff function | ||
| + | SUCCESSFUL_HANDOFF | ||
| + | FSBL Status = 0x1 | ||
| + | |||
| + | |||
| + | U-Boot 2016.01-00002-g46fc0b8-dirty (Oct 26 2016 - 14:24:01 -0400) | ||
| + | |||
| + | Model: Zynq Jlab VTP Board | ||
| + | Board: Xilinx Zynq | ||
| + | DRAM: ECC disabled 1 GiB | ||
| + | MMC: sdhci@e0100000: 0 | ||
| + | reading env.bin | ||
| + | In: serial@e0000000 | ||
| + | Out: serial@e0000000 | ||
| + | Err: serial@e0000000 | ||
| + | Model: Zynq Jlab VTP Board | ||
| + | Board: Xilinx Zynq | ||
| + | Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id | ||
| + | eth0: ethernet@e000b000</pre> | ||
| + | |||
| + | * Boot script can be interrupted during the count down period noted by | ||
| + | Hit any key to stop autoboot: | ||
Revision as of 16:08, 17 May 2023
uBoot boot interruption for configuration
- When the VME-VXS crate is power cycled, the display will show the uboot process.
Xilinx First Stage Boot Loader Release 2015.4 Jan 30 2017-11:51:58 Reset reason register 0x00000040 [SWDT_RST] = 0, System Watchdog timer [AWDT0_RST] = 0, CPU 0 Watch Timer [AWDT1_RST] = 0, CPU 1 Watch Timer [SLC_RST] = 0, Write to soft reset bit [DBG_RST] = 0, Debug command DAP controller [SRST_B] = 0, PS_SRST_B reset signal [POR] = 1, PS_POR_B reset signal reserved = 0, reserved Devcfg driver initialized Silicon Version 3.1 Boot mode is SD SD: rc= 0 SD Init Done Flash Base Address: 0xE0100000 Reboot status register: 0x60400000 Multiboot Register: 0x0000C000 Image Start Address: 0x00000000 Partition Header Offset:0x00000C80 Partition Count: 2 Partition Number: 1 Header Dump Image Word Len: 0x00015D85 Data Word Len: 0x00015D85 Partition Word Len:0x00015D85 Load Addr: 0x04000000 Exec Addr: 0x04000000 Partition Start: 0x000065D0 Partition Attr: 0x00000010 Partition Checksum Offset: 0x00000000 Section Count: 0x00000001 Checksum: 0xF7FB7F3F Application Handoff Address: 0x04000000 In FsblHookBeforeHandoff function SUCCESSFUL_HANDOFF FSBL Status = 0x1 U-Boot 2016.01-00002-g46fc0b8-dirty (Oct 26 2016 - 14:24:01 -0400) Model: Zynq Jlab VTP Board Board: Xilinx Zynq DRAM: ECC disabled 1 GiB MMC: sdhci@e0100000: 0 reading env.bin In: serial@e0000000 Out: serial@e0000000 Err: serial@e0000000 Model: Zynq Jlab VTP Board Board: Xilinx Zynq Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000
- Boot script can be interrupted during the count down period noted by
Hit any key to stop autoboot: