Difference between revisions of "The HPS Run Wiki"

Revision as of 11:57, 9 November 2014

[edit]

Shift Documentation
Short Term Schedule
Long Term Schedule
Accelerator
Monitoring

HPS Phone/Pager Numbers

Checklists

Procedures

Commissioning Plans:
- Beamline
- Trigger
- ECal
- SVT
SVT TOSP (1,2,3)

Manuals

JLab Logbooks

RC: Stepan Stepanyan

PDL: Harut Avagyan

Every Shift:

Follow run plan as outlined by RC
Keep shift summery up-to-date in HBLOG
Document any beam condition change and send scaler GUIs to HBLOG
Continuously check quality of data

Every Run:

a
b
c
d

MCC Daily Meetings

Run Plan: Nov. 9 - Nov. 10

Upstream beamline commissioning and beam tune using the tagger dump (beam will not go through the Hall). The goal is to get CW stable beam to the Hall-B tagger dump, on 2C24 harp (tagger harp) achieve beam parameters routinely used in Hall-B 6-GeV era X/Y width ~150 micron, and S/N on halo counters from harp wire >10E4.

Follow procedures in the "Beamline commissioning plan". Tuning beam to tagger dump is covered under item (A). Depending on the machine state, items (A.7) and (A.8) may not be feasible to complete at this time.
First establish 6-GeV era quality beam X/Y width ~150 micron, and S/N on halo counters from harp wire >10E4 on tagger (2C24) harp.
Then, using optics setting used in A. Freyberger's "[1]" simulations, achieve needed beam parameters at 2C24/tagger harp to deliver HPS requested beam ("pancake") on target in downstream alcove.

Beam
Energy	~2.0 GeV
Current	< 200.0 nA CW
Position
X	Y
~0 mm	~0 mm
Profile
X	Y
< 0.3 mm	< 0.3 mm

Target
#1	0 mm

Magnets
PS Current	0 A
Chicane Dipole #1	0 A
Chicane Dipole #2	0 A

DAQ
Configuration	___________________
Configuration file
Prescales
Thresholds
Events Per Run
Dead Time

Run Coordinator
DATE	NAME
DATE	NAME
DATE	NAME
DATE	NAME

Physics Division Liaison
DATE	NAME
DATE	NAME
DATE	NAME
DATE	NAME

Tagger Beam Dump Viewer

@@ Line 95: / Line 95: @@
 == Run Plan: Nov. 9 - Nov. 10 ==
-<font size="3">Upstream beamline commissioning and beam tune using the tagger dump (beam will not go through the Hall). The goal is to get CW stable beam to th eHall-B tagger dump and with beam parameters on 2C24 harp (tagger harp)  (x and Y width and S/N on halo counters from harp wire) close to values obtained with 6 GeV machine. </font>
+<font size="3">Upstream beamline commissioning and beam tune using the tagger dump (beam will not go through the Hall). The goal is to get CW stable beam to the Hall-B tagger dump, on 2C24 harp (tagger harp)  achieve beam parameters routinely used in Hall-B 6-GeV era <font color=red> X/Y width ~150 micron, and S/N on halo counters from harp wire >10E4</font>. </font>
 * Follow procedures in the "[https://wiki.jlab.org/hps-run/images/0/0d/HPS_beamline_commissioning.pdf Beamline commissioning plan]". Tuning beam to tagger dump is covered under item (A). Depending on the machine state, items (A.7) and (A.8) may not be feasible to complete at this time.
-* The beam parameters at 2C24/tagger harp needed to deliver HPS requested beam ("pancake") on target in downstream alcove are outlined in A. Freyberger's "[http://www.jlab.org/Hall-B/run-web/hps/manuals/HPS_Beamline.pdf]"
+* First establish 6-GeV era quality beam <font color=red> X/Y width ~150 micron, and S/N on halo counters from harp wire >10E4</font> on tagger (2C24) harp.
+* Then, using optics setting used in A. Freyberger's "[http://www.jlab.org/Hall-B/run-web/hps/manuals/HPS_Beamline.pdf]" simulations, achieve needed beam parameters at 2C24/tagger harp to deliver HPS requested beam ("pancake") on target in downstream alcove.
 {|