Difference between revisions of "The HPS Run Wiki"

Revision as of 08:01, 4 March 2015

[edit]

Shift Documentation
Short Term Schedule
Long Term Schedule
Monitoring

HPS Phone/Pager Numbers

Checklists

Procedures

Commissioning Plans:
- Beamline
- Trigger
- ECal
- SVT
SVT TOSP (1,2,3)

Manuals

JLab Logbooks

RC: Stepan Setpanyan

(757) 575-7540
9 575 7540 from Counting Room

PDL: Harut Avagyan

Every Shift:

Follow run plan as outlined by RC
Keep shift summery up-to-date in HBLOG
Document any beam condition change and send scaler GUIs to HBLOG
Send "scaler_hps" GUI to logbook at least twice per shift or any time run conditions change
Continuously check quality of data

Every Run:

a
b
c
d

MCC Daily Meetings

Run Plan: Dec. 8 - Dec. 10

Beamline commissioning studies using the Hall B dump, followed by studies of the ECal and Trigger. The goal is to get usable CW beam to the Hall-B dump, set up the chicane, and begin to study beam backgrounds and trigger rates.

Re-establish CW 1 pass beam to the Hall-B dump, setting beam to specified settings at the dump screen and the 2H02 harp. Chicane off. 5 nA.
Study the dependence of halo counter rates on beam position. Vary x and y of beam by +/- 7.5 mm, with beams parallel to specified settings above.

Record scaler rates, BPMs, 2H02 harp, and beam location on dump screen. Choose nominal position close to rate minimum, at old nominal, if possible.

With beam at nominal, set up chicane to specified currents for the -7% field point. Instructions provided in Counting House. Verify harp scan and record

location on dump screen. Tweak Frascati current if necessary, and record. Record scaler rates.

Ditto for -9% beam position.
If little change in scaler rates, use -7% setting as chicane standard. If large improvement in scaler rates in going to -9%, try -11%.
Select standard chicane settings.
Commission the HPS target, including measuring noise rates in the Ecal and halo counters vs beam current. Call Stepan before first use of target.
With 1.5 um Pt target, measure scalers and Ecal occ vs beam current.Record Ecal Scalers and scalaer display for each beam current.
If time allows, begin commissioning the Ecal and trigger with beam on target and data taking.
Expect beam off Tuesday day shift for machine studies. Beam recovery starts on Swing.
- See Full PDF, Click Here
- With any issue, contact Beamline Expert, Ecal Expert, DAQ Expert or RC.

Beam
Energy	~2.0 GeV
Current	< 200.0 nA CW
Position
X	Y
~0 mm	~0 mm
Profile
X	Y
< 0.1 mm	< 0.1 mm

Target
#1	0 mm

Magnets
PS Current	0 A
Chicane Dipole #1	0 A
Chicane Dipole #2	0 A

DAQ
Configuration	___________________
Configuration file
Prescales
Thresholds
Events Per Run
Dead Time

Run Coordinator
March 1 - March 11	Stepan Stepanyan
March 12 - March 18	Francios-Xavier Girod
March 19 - April 1	John Jaros
April 2 - April 8	Nathan Baltzell
April 9 - April 15	Takashi Maruyama
April 16 - April 22	Maurik Holtrop
April 23 - April 29	Raphael Dupre
April 30 - May 6	Takashi Maruyama

Physics Division Liaison
Harut Avakian

Webcams:

(only accessible inside Hall gateway)

Slow Controls:

Accelerator

HPS Data Catalog

DAQ On-Call
March 1 -	Sergey Boyarinov

ECAL On-Call
March 1 - March 9	Andrea Celentano
March 9 - March 23	Nathan Baltzell
March 23 - March 30	Holly Vance
March 30 - April 13	Gabriel Charles
April 13 - April 20	Raphael Dupre
April 20 - April 27	Michel Garcon
April 27 - May 4	Holly Vance

SVT On-Call
March 1 -	Expert #1

SlowControls On-Call
March 1 -	Expert #1

@@ Line 12: / Line 12: @@
 * [https://accweb.acc.jlab.org/hco/readiness Hot Checkout]
 <!--* [[Media:hps_hallb_checklist.pdf|Hall-B Checklist Preparing for Beam]]-->
+<br>
+*[http://www.jlab.org/Hall-B/hpsshifts HPS Shift Schedule]
+* [https://bta Beam Time Accounting]
 | valign=top |
@@ Line 44: / Line 47: @@
 ===JLab Logbooks===
-<!--* [http://opweb.acc.jlab.org/CSUEApps/bta03/bta.php Beam Time Accounting]-->
-<!--* [http://www.jlab.org/Hall-B/shifts Hall-B Shift Schedule]-->
 * [https://logbooks.jlab.org/book/elog MCC]
 * [https://logbooks.jlab.org/book/halog Hall-A]
@@ Line 228: / Line 229: @@
 |}
-= '''Accelerator''' =
-* [http://www.jlab.org/accel/ops_orientation/useful.html Accelerator Ops 1]
-* [http://www.jlab.org/accel/ops/ops.html Accelerator Ops 2]
-<!--* [http://opsweb.jlab.org/CSUEApps/elog/elog.php MCC Elog]-->
-* [https://bta Beam Time Accounting]
-* [http://accboard.acc.jlab.org/ Accelerator White Board Schedule]
-<!--* [http://opsntsrv.acc.jlab.org/org/MCC_whiteboard/MCC_scheduling_whiteboard.html Accelerator White Board Schedule]-->
@@ Line 263: / Line 253: @@
 | valign=top width=400|
+<br>Accelerator</b>
 * [http://clasweb.jlab.org/cgi-bin/HALL_ABC/hall_abc_new.pl End Station Status]
+* [http://www.jlab.org/accel/ops_orientation/useful.html Accelerator Ops 1]
+* [http://www.jlab.org/accel/ops/ops.html Accelerator Ops 2]
+* [http://accboard.acc.jlab.org/ Accelerator White Board Schedule]