Difference between revisions of "RGM RC Meeting Dec1 Dec7"

Revision as of 15:10, 6 December 2021

Last 24 hours
- Production running on Sn target
  - Established 90 nA for production, limited by region 3 DC current and occupancy
  - Gas alarm on FMT caused HV to shut down. [1] This wasn't noticed until 11 PM.
  - Overnight BOM trips caused frequent FSD
- This morning began switching to Ca-48 target
  - Went to restricted access at 7:30 AM
  - Work is still underway
  - Dan updated FTOF HV Settings
  - BOM repairs are complete
Issues
- DC Occupancies [2]
- SVT / MVT / BMT Occupancies
- Writing to tape
Upcoming Plan
- This evening, we will begin production on Ca-48
  - Re-establish beam, retune 2H01
  - Luminosity scan to establish production current
  - Any other calibrations?
Analysis
- 2.0 GeV vs. 1.6 GeV for BAND calibrations

Last 24 hours
- Mostly good beam, production running on C
- Orbit Lock changed to 2H01 yesterday at 3PM
- Low current run (20 nA), Run 15285, yesterday evening
- Resumed 90 nA production running on C at the end of Swing
- More DAQ issues resurfaced over night
  - Led to many short runs, which DO have good data and should be analyzed
Issues
- More DAQ trouble
  - Sergey switched the DAQ configuration to PROD66_noVTPread
- Torus cryo alarm at 9:45 PM
Upcoming Plan
- Sunday, 12/5, 8AM, Switch from C to Sn
  - This time works for Eugene.
  - Eugene's help will be needed to recenter the beam on target
- Monday, 12/6, Switch from Sn to Ca
  - Hall will go to restricted access from approx 7:30 AM to 5PM for target change work.
  - Denny is coordinating with MCC / RadCon to support this access.
- Weekend meetings
  - RC/PD meetings scheduled for 9AM over the weekend on the usual BJ.
  - No daily RC Meeting over the weekend, but I will send an RC e-mail update.
  - Are analysis meetings needed?
Analysis Meeting to Follow

Last 24 hours
- RF Recovery Day
- 20:30 Began restablishing beam to the Hall
- 10:45 Resumed production Running
- Overnight DAQ issues
- 04:00 - 08:00 Beam down due to blown fuse (Logbook entry)
- More DAQ Issues in the morning
- 11:10 Stable running again
Updated monitoring reference run to 15283 (from today)
DAQ Issues
MVT Trips Example
Question of DC Sector 1 Occupancies before Wednesday
- Previously looked odd Logbook entry
- Currently looks fine again Logbook entry
Short-term plan
- As of yesterday, plan was to switch to Sn on Friday afternoon, Ca on Monday.
  - Denny Insley plans to call for restricted access at 7:30 AM (Mon. 12/6), with goal to start work by 8:15 AM, finish by around the end of the day shift.
- Any changes to this plan?
- Any calibrations still needed on C (low current runs, etc.)?
Analysis Meeting to follow

@@ Line 1: / Line 1: @@
 == Monday, December 6, 2021 ==
 * Last 24 hours
-** Dan updated FTOF HV Settings
+** Production running on Sn target
+*** Established 90 nA for production, limited by region 3 DC current and occupancy
+*** Gas alarm on FMT caused HV to shut down. [https://logbooks.jlab.org/entry/3956842] This wasn't noticed until 11 PM.
+*** Overnight BOM trips caused frequent FSD
+** This morning began switching to Ca-48 target
+*** Went to restricted access at 7:30 AM
+*** Work is still underway
+*** Dan updated FTOF HV Settings
+*** BOM repairs are complete
 * Issues
-** DC Occupancies
+** DC Occupancies [https://logbooks.jlab.org/entry/3956825]
 ** SVT / MVT / BMT Occupancies
-** FMT HV was off
+** Writing to tape
-** BLM trips
 * Upcoming Plan
+** This evening, we will begin production on Ca-48
+*** Re-establish beam, retune 2H01
+*** Luminosity scan to establish production current
+*** Any other calibrations?
 * Analysis
+** 2.0 GeV vs. 1.6 GeV for BAND calibrations
 == Friday, December 3, 2021 ==