The HPS Run Wiki

[edit]

• Shift Documentation
• Short Term Schedule
• Long Term Schedule
• Monitoring

Important Phone Numbers Shift Schedule Checklists Shift-Taker's Checklist (old) Hot Checkout Beam Time Accounting

Procedures Commissioning Plans: Beamline Trigger ECal SVT SVT TOSP (1,2,3) Tunnel/Hall Access

Manuals Harp Scans SVT ECal (Annex) DAQ (CLAS Wiki (copy)) Beamline Turning ON/OFF chicane Slow Controls

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

RC: Stepan Stepanyan (757) 575-7540 9 575 7540 from Counting Room PDL: Harut Avagyan Every Shift: Follow run plan as outlined by RC Ask MCC if orbit locks are on, they should be. Keep shift summery up-to-date in HBLOG Document any beam condition change and send scaler GUIs to HBLOG Send "scaler_hps" GUI to logbook at least twice per shift or any time run conditions change Peform 2H02A harp scan ones per shift or when beam conditions changed based on beam monitors (BPMs, halo rates, beam-viewer) Fill out shift checklist in the logbook, HBLOG, using template at least ones per shift or when run conditions change Continuously check quality of data With any issue contact On-Call Experts or RC. SVT Instructions Before sending beam to Faraday cup, verify (and page expert if otherwise): SVT should be open: "Position" at 0.000 mm in scaler GUI SVT HV is off: all red/green indicators RED in SVT bias GUI The first time sending beam to the Faraday cup after the hall is closed, page the SVT expert. Every Run: a b c d MCC Daily Meetings

Run Plan:March 14-15 (morning) Setup Beam to Hall-B Tagger Dump and Studies of Beam Properties. When Rafayel is on shift, after 4pm, perform beam vertical motion during beam trips and recovery - turn off the beam move tagger harp (2C24) motor to ~97 in absolute position using the expert GUI ask MCC to deliver 100 nA beam, make sure rates on Struck from upstream halo counters are on order of few MHz (if needed make slight movements with motor to get desire rates). Rates can be seen not only on Struck scaler but also on Jorger scaler using fwd_scaler.ald) tell MCC that you will study beam motion during trip and recovery, so they should not bring beam back after the trip without your call start "waveform" program, and ask MCC to deliver beam, 100 nA. When beam trips stop the run after couple of minutes call MCC to see if they are ready to send the beam again, if so start the program again and ask for beam repeat this for at least 10 trips and recovery document each run in the logbook, start and end time and any details if necessary. Send HPS scaler GUI to logbook for every run Setup Beam to Hall-B Faraday cup Dump and Studies of Beam Properties. Ask MCC to turn OFF the beam, turn OFF and degous tagger magnet After tagger magnet is degaussed, change beam configuration on "bta" GUI to "Electron" Insert Chromax screen on the downstream viewer on the beam Ask for ~10 nA beam, watch cctv6 to make sure spot on the downstream viewer is clear and approximatly at the center of the screen Check to make sure Faraday cup and nA BPMs read similar curents Check beam position stability on 2H01 nA BPM If everything looks normal, rates on downstream counters are <10Hz, and on HPS-L and HPS-R are <30Hz at 10nA, proceed Use 2H02A harp do study beam profile (beam current should not exceed 20 nA), beam size should be X ~250 um Y < 150 um using downstream viewer GUI insert YAG then OTR screen. If beam is not well visible on these viewers, use the expert GUI to find proper position for each to have clear picture of the beam spot Energize HPS chicane - ask MCC to turn beam OFF, ramp up magnets to desired currents according to procedures (use the table) After magnets are at required settings (will take ~40 min) ask MCC for 10 nA beam Observe beam spot on chromox viewer, beam spot should be at the same place as before magnets were turned ON Beam Energy ~2.0 GeV Current < 200.0 nA CW Position X Y ~0 mm ~0 mm Profile X Y < 0.1 mm < 0.1 mm Target #1 0 mm Magnets PS Current 0 A Chicane Dipole #1 0 A Chicane Dipole #2 0 A DAQ Configuration ___________________ Configuration file Prescales Thresholds Events Per Run Dead Time

Accelerator White Board Schedule Weekly Run Coordinator Reports MCC Daily Meetings HPS Shift Schedule

Run Coordinator March 1 - March 11 Stepan Stepanyan March 12 - March 18 Francios-Xavier Girod March 19 - April 1 John Jaros April 2 - April 8 Nathan Baltzell April 9 - April 15 Takashi Maruyama April 16 - April 22 Maurik Holtrop April 23 - April 29 Raphael Dupre April 30 - May 6 Takashi Maruyama

Physics Division Liaison Harut Avakian

DAQ On-Call March 1 - May 4 Sergey Boyarinov

ECAL On-Call March 1 - March 9 Andrea Celentano March 9 - March 23 Nathan Baltzell March 23 - March 30 Holly Vance March 30 - April 13 Gabriel Charles April 13 - April 20 Raphael Dupre April 20 - April 27 Michel Garcon April 27 - May 4 Holly Vance

SVT On-Call March 8 - March 14 Sho Uemura March 15 - March 28 Omar Moreno March 29 - April 4 Pelle Hansson April 5 - April 8 Omar Moreno April 9 - April 19 Matt Graham April 20 - April 26 Tim Nelson April 27 - May 4 Sho Uemura

SlowControls On-Call March 1 - March 18 Hovane Egiyan March 19 - April 1 Stepan Stepanyan

Webcams: Tagger Beam Dump Viewer Faraday Cup Viewer ECal Chiller Viewer ECal LV Supply Viewer Alcove Viewer

Slow Controls: HPS MYA Variables Hall B EPICS Database

Accelerator: End Station Status Accelerator Ops 1 Accelerator Ops 2 Accelerator White Board Schedule

Offline: HPS Data Catalog Jenkins