Difference between revisions of "The HPS Run Wiki"

Revision as of 20:55, 8 March 2015

[edit]

Shift Documentation
Short Term Schedule
Long Term Schedule
Monitoring

Checklists

Procedures

Commissioning Plans:
- Beamline
- Trigger
- ECal
- SVT
SVT TOSP (1,2,3)
Tunnel/Hall Access

Manuals

JLab Logbooks

RC: Stepan Setpanyan

(757) 575-7540
9 575 7540 from Counting Room

PDL: Harut Avagyan

Every Shift:

Follow run plan as outlined by RC

Ask MCC if orbit locks are on, they should be.

Keep shift summery up-to-date in HBLOG

Document any beam condition change and send scaler GUIs to HBLOG

Send "scaler_hps" GUI to logbook at least twice per shift or any time run conditions change

Peform 2H02A harp scan ones per shift or when beam conditions changed based on beam monitors (BPMs, halo rates, beam-viewer)

Fill out shift checklist in the logbook, HBLOG, using template at least ones per shift or when run conditions change

Continuously check quality of data

With any issue contact On-Call Experts or RC.

Every Run:

a
b
c
d

MCC Daily Meetings

/* == Run Plan:March 8 - 9 (6am) == */ Setup Beam to Hall-B Faraday cup Dump and Studies of Beam Properties.

Ask MCC to turn OFF the beam, turn OFF and degous tagger magnet
After tagger magnet is degaussed, change beam configuration on "bta" GUI to "Electron"
Insert Chromax screen on the downstream viewer on the beam
Ask for ~10 nA beam, watch cctv6 to make sure spot on the downstream viewer is clear and approximatly at the center of the screen
Check to make sure Faraday cup and nA BPMs read similar curents
Use 2H02A harp do study beam profile and stability (beam current should not exceed 20 nA)

Run Plan:March 6 - 8

Setup Beam to Hall-B Tagger Dump and Studies of Beam Properties.

Aid MCC to establish physics quality CW 1 pass beam to the Hall-B tagger dump:
When reasonable beam spot is achieved on the tagger dump screen perform harp scans, 2C21 and tagger (2C24) harps. Note: harp scans must be performed with 10 nA beam current
If beam x/y sizes are ~<250 um, proceed with program below, otherwise ask MCC to retune

Ask MCC to deliver oval shape beam at the tagger (2C24) harp: x-width ~250 um, y-width << x-width (if tuning is going to be too long, more than 1/2 hour, use whatever asymmetric beam is available)
Continue with 2C24 (tagger) harp scans at 10 nA to check beam tilt angle motion over time, as well as beam position and width stability - ~2 hours (till about 7pm) with scans every 1/2 hour
Study beam tails as a function of current - every 1 hours increase beam curent to 100 nA and perform tagger harp scan. for harps analysis use tagger right and upstream left

Beam
Energy	~2.0 GeV
Current	< 200.0 nA CW
Position
X	Y
~0 mm	~0 mm
Profile
X	Y
< 0.1 mm	< 0.1 mm

Target
#1	0 mm

Magnets
PS Current	0 A
Chicane Dipole #1	0 A
Chicane Dipole #2	0 A

DAQ
Configuration	___________________
Configuration file
Prescales
Thresholds
Events Per Run
Dead Time

Run Coordinator
March 1 - March 11	Stepan Stepanyan
March 12 - March 18	Francios-Xavier Girod
March 19 - April 1	John Jaros
April 2 - April 8	Nathan Baltzell
April 9 - April 15	Takashi Maruyama
April 16 - April 22	Maurik Holtrop
April 23 - April 29	Raphael Dupre
April 30 - May 6	Takashi Maruyama

Physics Division Liaison
Harut Avakian

DAQ On-Call
March 1 - ?	Sergey Boyarinov

ECAL On-Call
March 1 - March 9	Andrea Celentano
March 9 - March 23	Nathan Baltzell
March 23 - March 30	Holly Vance
March 30 - April 13	Gabriel Charles
April 13 - April 20	Raphael Dupre
April 20 - April 27	Michel Garcon
April 27 - May 4	Holly Vance

SVT On-Call
March 1 - ?	Sho Uemura

SlowControls On-Call
March 1 - ?	?

Webcams:

Slow Controls:

Accelerator:

Offline:

@@ Line 102: / Line 102: @@
 | valign=top |
-== Run Plan:March 8 - 9 (6am) ==
+/* == Run Plan:March 8 - 9 (6am) == */
 '''<font size=3> Setup Beam to Hall-B Faraday cup Dump and Studies of Beam Properties.  </font>'''