The HPS Run Wiki

<!######################################## DOCS ####################################################> <!######################################## DOCS ####################################################>

[edit]

• Shift Documentation
• Short Term Schedule
• Long Term Schedule
• Monitoring

Important Phone Numbers Shift Schedule Checklists Shift-Taker's Checklist (old) Hot Checkout Beam Time Accounting

Procedures Commissioning Plans: Beamline Trigger ECal SVT SVT TOSP (1,2,3) Tunnel/Hall Access

Manuals Harp Scans SVT ECal (Annex) DAQ (CLAS Wiki (copy)) Beamline Turning ON/OFF chicane Slow Controls

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

<!####################################### SHORT TERM #################################################> <!####################################### SHORT TERM #################################################>

RC: Stepan Stepanyan (757) 575-7540 9 575 7540 from Counting Room PDL: Harut Avagyan Every Shift: Follow run plan as outlined by RC Ask MCC if orbit locks are on, they should be. Keep shift summery up-to-date in HBLOG Document any beam condition change and send scaler GUIs to HBLOG Send "scaler_hps" GUI to logbook at least twice per shift or any time run conditions change Peform 2H02A harp scan ones per shift or when beam conditions changed based on beam monitors (BPMs, halo rates, beam-viewer) Fill out shift checklist in the logbook, HBLOG, using template at least ones per shift or when run conditions change Continuously check quality of data With any issue contact On-Call Experts or RC. SVT Instructions Before sending beam to Faraday cup, verify (and page expert if otherwise): SVT should be open: "Position" at 0.000 mm in scaler GUI SVT HV is off: all red/green indicators RED in SVT bias GUI The first time sending beam to the Faraday cup after the hall is closed, page the SVT expert. Every Run: a b c d MCC Daily Meetings

Run Plan:March 10-12 (morning) Setup Beam to Hall-B Tagger Dump and Studies of Beam Properties. Ask MCC to turn ON tagger magnet Aid MCC to establish physics quality CW 1 pass beam to the Hall-B tagger dump: When reasonable beam spot is achieved on the tagger dump screen perform harp scans, 2C21 and tagger (2C24) harps. Note: harp scans must be performed with 10 nA beam current MCC delivers beam that is optimized for HPS, beam profile should be small at 2C21 (X/Y widths ~50 um) and should be large at tagger (2C24) harp (widths on 45/Y/X ~300 um), see previous harp scans Make sure 2C21 and 2C24 nA BPMs read stable X/Y positions. Postions on both BPMs must be close to zero as much as possible (at least |X/Y|<1). Make sure orbit locks are on and operational Continue with tagger (2C24) harp scans at 10 nA to check beam position and width stability for ~ 1h - scans every 15 min If beam position (mean values of fitted peaks) are stable with <0.1 mm, proceed with the program, otherwise work with MCC to stabilize the beam Study beam tails as a function of current - perform tagger harp scans with different harp setting at 10nA, 20nA, 50nA, 100nA: nominal setting - "Speed during scan" = 0.5 and "Time between scaler reads" = 0.07 "Speed during scan" = 0.5 and "Time between scaler reads" = 0.35 "Speed during scan" = 0.25 and "Time between scaler reads" = 0.7 Harp settings can be changed on the GUI by typing new values in the window For harps analysis use upstream left Beam Energy ~2.0 GeV Current < 200.0 nA CW Position X Y ~0 mm ~0 mm Profile X Y < 0.1 mm < 0.1 mm Target #1 0 mm Magnets PS Current 0 A Chicane Dipole #1 0 A Chicane Dipole #2 0 A DAQ Configuration ___________________ Configuration file Prescales Thresholds Events Per Run Dead Time

<!####################################### LONG TERM #################################################> <!####################################### LONG TERM #################################################>

Accelerator White Board Schedule Weekly Run Coordinator Reports MCC Daily Meetings HPS Shift Schedule

Run Coordinator March 1 - March 11 Stepan Stepanyan March 12 - March 18 Francios-Xavier Girod March 19 - April 1 John Jaros April 2 - April 8 Nathan Baltzell April 9 - April 15 Takashi Maruyama April 16 - April 22 Maurik Holtrop April 23 - April 29 Raphael Dupre April 30 - May 6 Takashi Maruyama

Physics Division Liaison Harut Avakian

DAQ On-Call March 1 - ? Sergey Boyarinov

ECAL On-Call March 1 - March 9 Andrea Celentano March 9 - March 23 Nathan Baltzell March 23 - March 30 Holly Vance March 30 - April 13 Gabriel Charles April 13 - April 20 Raphael Dupre April 20 - April 27 Michel Garcon April 27 - May 4 Holly Vance

SVT On-Call March 8 - March 14 Sho Uemura March 15 - March 28 Omar Moreno March 29 - April 4 Pelle Hansson April 5 - April 8 Omar Moreno April 9 - April 19 Matt Graham April 20 - April 26 Tim Nelson April 27 - May 4 Sho Uemura

SlowControls On-Call March 1 - ? ?

<!####################################### MONITORING #################################################> <!####################################### MONITORING #################################################>

Webcams: Tagger Beam Dump Viewer Faraday Cup Viewer ECal Chiller Viewer ECal LV Supply Viewer Alcove Viewer

Slow Controls: HPS MYA Variables Hall B EPICS Database

Accelerator: End Station Status Accelerator Ops 1 Accelerator Ops 2 Accelerator White Board Schedule

Offline: HPS Data Catalog Jenkins