The HPS Run Wiki

[edit]

• Shift Documentation
• Short Term Schedule
• Long Term Schedule
• Monitoring

Important Phone Numbers Shift Schedule Shift-Taker's Checklist (old) Hot Checkout Beam Time Accounting

Procedures Commissioning Plans: Beamline Trigger (old) ECal SVT SVT TOSP (1,2,3) Tunnel/Hall Access

Manuals Harp Scans Beam Trip Runs SVT ECal (Annex) DAQ Beamline Turning Chicane ON/OFF Slow Controls

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

RC: John Jaros (757) 575-7540 9 575 7540 from Counting Room PDL: Stepan Stepanyan Every Shift: Follow run plan as outlined by RC Once BPMs are calibrated, ask MCC if orbit locks are on, they should be. Keep shift summary up-to-date in HBLOG Update the run table on Google Docs. Document any beam condition change and send scaler GUIs to HBLOG Send "scaler_hps" GUI to logbook at least twice per shift or any time run conditions change Peform 2H02A harp scan ones per shift or when beam conditions changed based on beam monitors (BPMs, halo rates, beam-viewer) Fill out shift checklist in the logbook, HBLOG, using template at least ones per shift or when run conditions change Continuously check quality of data With any issue contact On-Call Experts or RC. SVT Instructions Before sending beam to Faraday cup, verify (and page expert if otherwise): SVT should be open: "Position" at 0.000 mm in scaler GUI SVT HV is off: all red/green indicators RED in SVT bias GUI The first time sending beam to the Faraday cup after the hall is closed, page the SVT expert. Acceptable Beam Conditions: Before accepting beam, make sure all the conditions are met - beam profile and halo rates are what you expect (or very close to it). If unsure call to RC, PDL, or beamline expert! Beam optics setting is such that at 2H02A harp the beam profile will be as requested by HPS,wide in X-direction and narrow in Y. This optics setting will make the beam profile at 2C21 harp narrow in both directions, while profile on the "tagger" or 2C24 harp wide in both directions. The halo counter rates before HPS must be low: UPS-L and UPS-R few Hz/nA, if tagger magnet is energized TAG-L/T/T2 ~10Hz/nA [1], if beam is going to Faraday cup dump then tagger counters and downstream counters should count <<1 Hz/nA The halo counter rates on HPS, HPS-L/R/T/SC, depends on the collimator and HPS chicane settings, but should not be more than 100 Hz/nA[2] As halo counters, positions on BPMs and the settings of correctors also must be close to what where before. Always read previous log entries, compare settings of BPMs and correctors with previous settings using scaler_hps GUI. Every Run: a b c d MCC Daily Meetings

DO NOT RUN MORE THAN 30 MINUTES ABOVE 50 nA WITHOUT THE BEAM BLOCKER PUT BEAM BLOCKER IN FOR LONG RUNNING AT HIGH CURRENT Run Plan:March 22-23, 2015 (day/swing/owl) Overview: Very bad beams last night. We need better standards for what is acceptable at 2C21 and 2C24, and upstream halo counters before sending beam downstream to the dump. We returned to tagger and MCC will work on calibrating upstream BPMs. Tief will work on optics matching starting 1PM today. Expect to open hall Tuesday AM, but this is still being dicussed. Program: 1) MCC retunes upstream beam and calibrates BPMs; (2) MCC works on beamline optics, hopefully restoring beams to alcove when complete;(3) when have decent beams to alcove, try to have MCC calibrate downstream BPMs;(4)get good spot on Chromax, low counts on halo counters, and then set-up chicane. 5) scan target vertically and horizontally, halo rates vs target (5) Take data. Subsystem commissioning studies: more trigger commissioning studies, SVT commissioning. MCC calibrates upstream bpms MCC works on beam optics and matching, and tunes beam to tagger After MCC finishes beam tune and upstream bpms are calibrated record harp scans at 2C21 and 2C24. These must be good scans, good S/N, no tails, and low halo count rates before proceeding. make sure no bleedthrough-- counts when no beam? After beam tune is done send HPS scaler GUI to the logbook with explanation Restore Beam to the Hall-B Faraday cup Dump and Setup HPS. Ask MCC to turn OFF the beam, turn OFF and degauss tagger magnet After tagger magnet is degaussed, change beam configuration on "bta" GUI to "Electron" Make sure target is out Insert Chromax screen on the downstream viewer on the beam. 4mm SVT Protection collimator in place Restore 1 nA CW beam and have MCC bring beam to y~-5mm; x~5mm. Record spot. Record scalers. Halo counters and Ecal must have low rates to proceed. Record position at 2H02 harp. Repeat at 10 nA. Must have good spots, nominal sizes, no tail to proceed. Position ok? record scalers and beam location on screen. Energize Chicane follow standard procedures beam spot on Chromax should be unmoved. If not, tune Frascati slightly. See caution below. SVT wire scan. Check beam position OK in x and y. Be very careful when changing magnet currents when beams are on. Must enter new current ACCURATELY. Small steps only. Turn beam off and insert HPS target, 4um W Do horizontal scan of beam on target. Using table provided, first change Frascati settings, then PS settings to move beam left and right on the target with ~1mm step. Small changes only. Return to nominal beam positon. Do vertical scan of target at fixed beam position. Measure halo counter/ecal rates vs target position. Record data and graph Do scan of SVT collimator, measuring counter rates vs SVT collimator position with nominal beam position. Subsystem Commissioning Studies. Begin Data Taking. Make sure DAQ is OK for data taking More Trigger commissioning data runs. See Valery's note on the run Wiki under commissioning trigger. When SVT is ready for data, begin integrated data taking. Call Omar. Absent other requests, take data at 50 nA. Turn beams over to MCC during day shift March 23 for bpm calibration Beam Energy ~2.0 GeV Current < 200.0 nA CW Position X Y ~0 mm ~0 mm Profile X Y < 0.1 mm < 0.1 mm Target #1 0 mm Magnets PS Current 0 A Chicane Dipole #1 0 A Chicane Dipole #2 0 A DAQ Configuration ___________________ Configuration file Prescales Thresholds Events Per Run Dead Time

Accelerator White Board Schedule Weekly Run Coordinator Reports MCC Daily Meetings HPS Shift Schedule

Run Coordinator March 1 - March 11 Stepan Stepanyan March 12 - March 18 Francios-Xavier Girod March 19 - April 1 John Jaros April 2 - April 8 Nathan Baltzell April 9 - April 15 Takashi Maruyama April 16 - April 22 Maurik Holtrop April 23 - April 29 Raphael Dupre April 30 - May 6 Takashi Maruyama

Physics Division Liaison Stepan Stepanyan

Beamline On-Call NOW Takashi Maruyama DAQ On-Call NOW Sergey Boyarinov

ECAL On-Call March 1 - March 9 Andrea Celentano March 9 - March 23 Nathan Baltzell March 23 - March 30 Holly Vance March 30 - April 13 Gabriel Charles April 13 - April 20 Raphael Dupre April 20 - April 27 Michel Garcon April 27 - May 4 Holly Vance

SVT On-Call March 8 - March 14 Sho Uemura March 15 - March 28 Omar Moreno March 29 - April 4 Pelle Hansson April 5 - April 8 Omar Moreno April 9 - April 19 Matt Graham April 20 - April 26 Tim Nelson April 27 - May 4 Sho Uemura

SlowControls On-Call March 1 - March 18 Hovanes Egiyan March 19 - April 1 Stepan Stepanyan

Webcams: Tagger Beam Dump Viewer Faraday Cup Viewer ECal Chiller Viewer ECal LV Supply Viewer Alcove Viewer

Slow Controls: HPS MYA Variables Hall B EPICS Database

Accelerator: End Station Status Accelerator Ops 1 Accelerator Ops 2 Accelerator White Board Schedule

Offline: Run Spreadsheet HPS Data Catalog Jenkins / Nexus Shift Docs @ GitHub