Run Group M

[edit]

• Shift Documentation
• Phone Numbers
• Short Term Schedule
• Notes/Known Issues
• Shift Expert
• Remote Worker Shift
• Monitoring
• Useful Links

Shift Schedule ESAD, COO, RSAD Shift Checklist Hot Checkout Beam Time Accounting See guidance at BTA User Guide.

Manuals DC FTOF ECAL LTCC HTCC RICH: Expert Shift CTOF CND SVT MVT MVT turn on procedure FT Beamline Torus Power-Up/Down Procedure Solenoid Power-Up/Down Procedure Target Operation manual DAQ Slow Controls BAND

Procedures Physics-Quality Beam Performing Møller Runs Performing Harp Scans Tunnel/Hall Access ESAD, COO, RSAD

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

If calling local numbers (with area code prefix 757) from the counting room dial 9+[last 7 digits]. To call other area codes dial 91+[ten digit number]

Role Phone Number Hall B Run Coordinator (757) 575-7540 (cell) Hall B Physics Division Liaison (757) 876-1789 (cell) MCC 7048 Crew Chief 7045 Crew Chief (757) 876-3367 (cell) Program Deputy (757) 876-7997 (cell) RadCon (757) 876-1743 (cell) Gate House Guard 5822 Location Phone Number Hall B Floor 5165 Hall B Space Frame 5170 and 5171 Hall B Forward Carriage 5371 Hall B Gas Shed 7115 Hall B Counting House 5244 (Shift Expert) Hall B Counting House (757) 329-4846 (Shift Expert cell) Hall B Counting House 5245 or 5126 (Shift Worker) Hall A Counting House 5501 Hall C Counting House 6000 Hall D Counting House 5504

Hall B System Phone Number On-Call Person Engineering (757) 748-5048 (cell) (757) 897-9060 (cell) Engineering On-Call (primary) Denny Insley (secondary) Slow Controls (757) 748-6922 (cell) Nathan Baltzell Beamline (757) 303-3996 (cell) Eugene Pasyuk DC (757) 218-4372 (cell) (757) 748-5048 (cell) Florian Hauenstein (primary) Engineering On-Call (secondary) SVT/MVT/MM (757) 541-7539 (cell) (757) 753-7769 (cell) Yuri Gotra (primary) Rafo Paremuzyan (secondary) ECAL (757) 810-1489 (cell) Cole Smith FTOF/CTOF/CND (757) 344-7204 (cell) Daniel Carman ALERT (757) 329-4844 (cell) Raphael Dupré HTCC/LTCC (757) 344-7174 (cell) Youri Sharabian FT (757) 344-1848 (cell) Raffaella De Vita BAND (757) 310-7198 (cell) Florian Hauenstein RICH (757) 344-3235 (cell) (757) 748-6922 (cell) Christopher Dilks (primary) Nathan Baltzell (secondary) DAQ (757) 232-6221 (cell) Sergey Boiarinov HYDRA (317) 550-9226 (cell) Torri Jeske Authorized Hall B Solenoid/Torus Operators Hall B Denny Insley, Morgan Cook, Eugene Pasyuk Magnet Group Probir Ghosha, Renuka Rajput-Ghoshal Detector Support Group Brian Eng, Pablo Campero, Tyler Lemon DC Power Onish Kumar, Sarin Philip

• Note, all non-JLab numbers must be dialed with an area code. When calling from a counting-house landline, dial "9" first.
• To call JLab phones from outside the lab, all 4-digit numbers must be preceded by 757-269
• Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

CLAS12 Run Group M, Fall 2021

Beam energies: 2.1, 4.0, 6.0 GeV (1.96 GeV/pass)

RC: Susan Schadmand and Sebastian Kuhn

• Susan Schadmand (757) 575-7540, susansch@jlab.org
• Sebastian Kuhn (757) 639-6640, kuhn@jlab.org
• 9 575 7540 from Counting Room

PDL: Valery Kubarovsky

• (757) 876-1789
• 9 876-1789 from Counting Room
• vpk@jlab.org

Jan 27 - 29, 2022

4GeV 22nA on LAr

• beam conditions https://logbooks.jlab.org/entry/3978975
• count down 1B events 4 GeV on LAr

Run Plan: Jan 30 - Jan 31, 2022

Production runs use PROD67_noVTPread and the trigger rgm_6GeV_inb_v1_0.trg .
Run duration 100M events or 4 hours, whichever comes first.

• LAr target is empty, cell stays in position, Beam blocker IN

• Empty target run
  • FC calibration (4GeV) is done
  • Take 2 hours of empty target run at 150 nA

• Carbon target (single foil 2 mm) IN
  • FC calibration for C target is loaded
  • Run with 90 nA

• Monday pass change (6GeV beam)
  • Need to establish quality beam, repeat beam centering, beam blocker calibration.
  • OUTLOOK: Run on Ar, Sn and C with 6 GeV beam

DAQ configuration

PROD67_noVTPread , production trigger rgm_6GeV_inb_v1_0.trg .

NOTE: BOTH the shift expert AND the shift worker need to check monitoring histograms at least once every 1-2 hours to make sure there are no major detector problems.

At the end of each run, follow the STANDARD DAQ RESTART SEQUENCE

• "end run", if the run ended correctly then: "prestart", "go"

• if the run did not end correctly or if any ROCs had to be rebooted:
• "cancel", "reset"
  • "configure", "download", "prestart", "go"
• After each step, make sure it is completed in the Run Control message window. If a ROC has crashed, find which one it is, issue a roc_reboot command ON JUST THAT ROC and try again. Contact the DAQ expert if there are any questions.

References and Standards

(last update 01/18/2022- 23:30)

Nominal Beam Positions

• 2H01, X: -0.6 mm, Y: 0.8 mm
• 2C24, X: -2.0 mm, Y: +0.6 mm

FSD Thresholds

• Upstream: 2000 Hz
• Midstream: 2000 Hz
• Downstream: 500000 Hz
• BOM: 10000
• 5 ms dwell time

Reference Harp Scans for Beam on Faraday Cup: 2H01 [1]

Reference Harp Scans for Beam on Tagger dump: 2C21 [2], tagger harp [3]

Reference Monitoring Histograms (6 nA, production C) [4] Old reference Monitoring Histograms (50 nA, production LD2) [5]

Counter rates

• Upstream counters integrated rates: 0-15 Hz (acceptable up to 100 Hz are acceptable) @50 nA.
• Midstream counters: 10-20 Hz (acceptable up to 50 Hz) @50 nA.
• Counting rates of ~ hundreds of Hz may indicate bad beam tune or bleed-through from other Halls.

Beamline vacuum: should be not higher than 5e-5.

Notes LTCC is NOT used in this experiment. HV should be kept OFF. The main lights in the Hall (dome lights) and the Forward Carriage lights are being kept off because of light leaks affecting some of the detectors. If these lights are switched on during access, they should be switched off when leaving the Hall. Refer to these photos: ON: [6] OFF: [7] Note that the dome lights when switched off cannot be turned back on immediately because they require 10-15 min to cool down. Be very mindful of the background rates in the halo counters, rates in the detectors, and currents in the SVT for all settings to ensure that they are at safe levels. The integrated rates on the upstream counters have to be in the range 0-15 Hz (rates up to 100 Hz are acceptable) and the rates on the midstream counters have to be in the range 10-20 Hz (acceptable up to 50 Hz) @50 nA. Counting rates in the range of hundreds of Hz may indicate a bad beam tune or bleed-through from other Halls. When the beam is being delivered to the Faraday Cup: the Fast Shut Down elements: Upstream, Midstream, Downstream, BOM, and Solenoid should always be in the state UNMASKED No changes to the FSD threshold should be made without RC or beamline expert approval Do not run more than 30 minutes with >150 W beam to Faraday cup without the beam blocker, eg https://logbooks.jlab.org/entry/3979277 Any request for a special run or change of configuration has to be approved by the RC & documented Do not turn OFF FTOF HVs, even during the beam tune with CW beam (turn off if tuned/pulsed beam in the upstream beamline) Turn DC HV off only for beam tuning; if no beam is available or when the beam is stable, keep them on even if you are not taking data. Reset the online monitoring histograms frequently to avoid histogram saturation. In case of a Torus and/or Solenoid Fast Dump do the following: Notify MCC to request beam OFF and to drop Hall B status to Power Permit Call Engineering on-call Make a separate log entry with copies to HBTORUS and HBSOLENOID logbooks. In the "Notify" field add Probir Goshal, Dave Kashy, and esr-users@jlab.org Notify Run Coordinator Turn off all detectors If responding to RICH or Trigger alarms please post screens also to RICH or HBTRIGGER logbook, respectively.

Known Issues DAQ ROC rate tdcecal4 is double wrt the 5 othersectors, https://logbooks.jlab.org/entry/3979286 DAQThe error messages " ERR: event# ..." for crates tdcband1, tdcecal1 and tdcecal6 are NOT a problem PCAL transient: mu strip occupancy hole in U view TDC, https://logbooks.jlab.org/entry/3978499, https://logbooks.jlab.org/entry/3978736 ECAL one strip of TDC ECout W strip sector4 is hot, https://logbooks.jlab.org/entry/3979286 ECAL HV SEC2_WI_E36 is known to be problematic. Channel stays off for now. BMT off: occupancy Z, layer 3, sector 1, detetcor 7, S1L3 strip HV is off due to high leakage, https://logbooks.jlab.org/entry/3970886 BMT off: occupancy Z, layer 5, sector 2, detetcor 14 RICH FPGA temperatures can show yellow tiles. Yellow tiles in the RICH temperature map are normal. It is done just to pay attention to the tiles with temp>70 degrees. The alarm is set to 75 degrees https://logbooks.jlab.org/entry/3975547 RICH noisy pixels normal, https://logbooks.jlab.org/entry/3972462 . There is a current new issue seen in the occupancy spectrum, https://logbooks.jlab.org/entry/3978583 IOCBTARG In case of loss of communication, follow instructions at https://logbooks.jlab.org/entry/3502218 Check that no unnecessary beamline-related screens are open. This includes particularly the big beamline overview screen, but also and any motor/harp/collimator screens, and IOC health screens.

Follow the [Short Term Schedule] as outlined by RC includes Run Plan, DAQ configuration, and References and Standards Keep shift summary up to date in HBLOG. Record all that happens. Cycle the FMT gas once per shift, in-between runs. Pease log in shift summary. If it is not reset, the interlock may drop and disable the HV. Turning off and on the gas flow without pausing to avoid HV trips. If the HV tripped, make sure that once gas flow is restarted and the flow differential is down to reasonable values, to turn the FMT HV back on and let it ramp all the way up. Remember that this experiment is only using 3 FMT layers, not 6. Do a RICH recovery (press the RICH Recovery button on the GUI) once daily during day shift, between runs. Please log in shift summary. Fill out BTA hourly. Click "Load from EPICS" to automatically fill the left side then correct as needed. Accelerator beam time: ABU: acceptable beam used (eg harp scans, calibrations, trigger settings, running) BANU: beam acceptable but not used (eg radiator change or our problems) BNA: beam not acceptable (eg tuning, drifting, not focused) Experiment beam time ER: experiment ready PCC: planned configuration change (when beam is masked while radiators are moved, DAQ (roc rebooting, restarting runs)), if more than 5 minutes, put a short comment, eg harp scans or DAQ. UED: unplanned experiment down (hardware failure) In case of other questions or uncertainties of what to do, call the RC or PDL (remote) shift worker: see dedicated Remote Shifts tab above.

Zoom for 24-7 communication with counting house: https://jlab-org.zoomgov.com/j/1619881100 Passcode REQUIRED: 927417 Remind the expert in the counting house to restart their zoom, if necessary Remote VNC connection instructions: https://logbooks.jlab.org/entry/3906039 All necessary applications should be avaible from the desktop menu (left/right click on the desktop) EPICS GUIs should be accessed ONLY via the desktop menu or by running clascss-remote. Remote Demonstration Video (150 MB) Tasks Every Run: WITH BEAM, log screen shots of Beamline Overview, in VNC or Web Browser CLAS12 Trigger rates and DAQ status upload monitoring plots (mon12) to logook Reference, current, and 5 most recent runs, choose a reference run, here are some choices (the reference numbers refer to logbook entries): ref 6 nA, production C, https://clas12mon.jlab.org/mon12/histograms/?reference=3973807 ref 50 nA, production LD2, https://clas12mon.jlab.org/mon12/histograms/?reference=3943458 Every Shift: Fill the shift checklist Log screen shots of RICH temperature and scaler maps Regularly: Log the strip charts in time intervals according to the x-axis time span, using the liveplot configuration Beamline4Logbook, see https://logbooks.jlab.org/entry/3978837 . Or, in VNC or Web Browser: Upstream/Midstream Halo Counters, Downstream Halo Counters, Beam Currents, BPM Positions reset & check spectra frequently NOTE: some spectra have a choice of histogram sets per sector, only the currently displayed set ends up in the logbook entry; ECAL (ADC Histograms, FADC Timing, TDC Histograms) FTOF (ADC Histograms, FADC Timing, TDC Histograms, GMEAN)

Backup shifter contact info Name Email Cell phone Justin Estee esteejus@mit.edu Andrew Denniston awild@mit.edu Sara Ratliff ratliff_sara@gwmail.gwu.edu Erin Seroka erinseroka@gwmail.gwu.edu

Webcams Tagger Beam Dump Viewer CND/CTOF Ammeter FTOF/ECAL Ammeter Hall Fisheye Saclay Cryotarget Faraday Cup Beam Viewer To reboot it, run beam-viewer-reboot on a clonpc.

Manuals CED Manual MON12 Manual off-line Manual

Hall Webcams Hall A Hall B Hall C Hall D

Epics on the web Hall B WebOPI (CUE Login) Accelerator (CUE Login)

Live Monitoring Links CLAS12 Monitoring Timelines Live Charge Collected Plots Live Luminosity Collected Plots

Hall-B Operation Safety Procedures Run Group M Analysis Wiki RCDB CLAS12 mon page Comparison between mon12 histograms (last 5 runs) Accumulated Charge Accumulated datasize Run Coordinator Schedule Target and Run Plan Summary Full Run Plan Run lists

Accelerator Accelerator Whiteboard Program Deputy Shift Plans Run Coordinator Reports Beam Time Accounting Reports References Proposal

ZOOM meetings 07:45 RC/PD Morning Meeting 08:00 MCC/OPS Morning Meeting 15:30 Daily RC Meeting Zoom Link Meeting ID: 161 269 7153 Passcode: 474207 On site - CEBAF Center F324-325 conference room Daily Analysis Meeting to follow directly after Meeting Agendas