Engineering Run

[edit]

• Shift Documentation
• Phone Numbers
• Short Term Schedule
• Monitoring
• Useful Links

Shift Schedule Shift Checklist Hot Checkout Beam Time Accounting

Manuals DC FTOF ECAL LTCC HTCC RICH: expert novice CTOF CND SVT MVT MVT turn on procedure FT Beamline Torus Power-Up and Power-Down Procedure Solenoid Power-Up and Power-Down Procedure Target DAQ Slow Controls

Procedures Beamline Commissioning Plan Establishing Physics-Quality Beam Performing Møller Runs Performing Harp Scans Commissioning Plan Simulation Background Estimates Trigger Commissioning Plan Tunnel/Hall Access DAQ Quick Reference/Recovery

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

Role Phone Number Hall B Run Coordinator (757) 575-7540 (cell) Hall B Physics Division Liaison (757) 876-1789 (cell) MCC 7048 Crew Chief 7045 Crew Chief (757) 876-3367 (cell) Program Deputy (757) 876-7997 (cell) RadCon (757) 876-1743 (cell) Gate House Guard 5822 Location Phone Number Hall B Floor 5165 Hall B Space Frame 5170 and 5171 Hall B Forward Carriage 5371 Hall B Gas Shed 7115 Hall B Counting House 5244 (Shift Expert) Hall B Counting House (757) 329-4846 (Shift Expert cell) Hall B Counting House 5245 or 5126 (Shift Worker) Hall A Counting House 5501 Hall C Counting House 6000 Hall D Counting House 5504

Hall B System Phone Number On-Call Person Engineering (757) 748-5048 (757) 897-9060 Engineering On-Call (primary) Denny Insley (secondary) Slow Controls (757) 748-6922 Nathan Baltzell Beamline (757) 303-3996 Eugene Pasyuk DC (757) 218-4372 (757) 748-5048 Florian Hauenstein (primary) Engineering On-Call (secondary) SVT/MVT/MM (757) 541-7539 (757) 753-7769 Yuri Gotra (primary) Rafo Paremuzyan (secondary) ECAL (757) 810-1489 Cole Smith FTOF/CTOF/CND (757) 344-7204 Daniel Carman ALERT AHDC / Target - (757) 329-4844 ATOF - (757) 991-2798 Raphael Dupré Whitney Armstrong HTCC/LTCC (757) 344-7174 Youri Sharabian FT (757) 344-1848 Raffaella De Vita BAND (757) 310-7198 Florian Hauenstein RICH (757) 344-3235 (757) 748-6922 Christopher Dilks (primary) Nathan Baltzell (secondary) DAQ (757) 232-6221 Sergey Boiarinov HYDRA (317) 550-9226 Torri Jeske Authorized Hall B Solenoid/Torus Operators Hall B Denny Insley, Morgan Cook, Eugene Pasyuk Magnet Group Probir Ghosha, Renuka Rajput-Ghoshal Detector Support Group Brian Eng, Pablo Campero, Tyler Lemon DC Power Onish Kumar, Sarin Philip

• Note, all non-JLab numbers must be dialed with an area code. When calling from a counting-house landline, dial "9" first.
• To call JLab phones from outside the lab, all 4-digit numbers must be preceded by 757-269
• Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

Click Here to edit Phone Numbers. Note, you then also have to edit this page to force a refresh.

CLAS12 Engineering Run, Winter 2018
Beam energy 10.6 GeV (5 pass)
Important: Document all your work in the logbook!
Remember to fill in the run list at the beginning and end of each run (clas12run@gmail.com can fill the run list)

RC: Daniel S. Carman

• (757) 575-7540
• 9 575 7540 from Counting Room
• carman@jlab.org

PDL: Eugene Pasyuk

• (757) 876-1789
• 9 876-1789 from Counting Room
• pasyuk@jlab.org

• Note 1: Be very mindful of the background rates in the halo counters, rates in the detectors, and currents in the SVT for all settings to ensure that they are at safe levels.

• Note 2: At the end of each run, follow the DAQ restart sequence "end run", "abort", "reset", "download", "prestart", "go". After DAQ prestart is complete reboot the scaler IOCs with the command: iocjscalerRestartAll.sh. Note: After each step, make sure it is complete in the Run Control message window. If a roc has crashed, find which one it is and issue a roc_reboot command and try again. Contact the DAQ expert if there are any questions.

• Note 3: Nominal beam positions: 2C21 (X=0.0 mm, Y=0.0 mm), 2C24 (X=0.0 mm, Y=0.7 mm), 2H01 (X=0.3 mm, Y=-0.6 mm)

• Note 4: With beam to the Faraday Cup, typical rates an all halo counters upstream from the target should be either 0 or of the order of few counts. Count rates in the range of tens or more may indicate bad beam tune or bleed-through from other Halls.

Run Plan: (last update 2/3 - 14:30) All studies will take data at 100% torus field (negatives inbending) and 100% solenoid field (positive polarity on supply). The beam position should be as indicated above. Make sure FSD thresholds are set correctly for whatever current is selected (refer to instructions in the "Establish-physics quality beam" procedure at [1]), integration time is set to 5 ms, and that the orbit locks are on. Take data with PROD/elec_htcc_1phe_pcal_300.cnf at 35 nA; 2 hr long runs. Continue trigger development studies. This work will be led by the trigger/DAQ experts. Hall B work for Monday: Ramp down solenoid (torus can stay up) (RC) Complete shielding addition outside scattering chamber (Hall B Engineering) Restore beamline (Hall B Engineering) Replace FT-Hode mezzanine board (N. Zachary) Work on DC cable swaps (M. Cook + M. Mestayer) Work on vacuum gauge (D. Anderson) Investigate polarity of busy signal (S. Boyarinov) Setup gated/ungated scalers and clock scalers (S. Boyarinov) SAF111 walkthrough (E. Pasyuk) Pass change (5-pass to 3-pass)

General Instructions: For a given beam current, compute the FSD thresholds according to the Establish Physics Quality Beam document. Call MCC to update the values. Contact the beamline expert if there are questions about setting the FSD thresholds. The main lights in the Hall (dome lights) and the Forward Carriage lights are being kept off because of light leaks affecting some of the detectors. If these lights are switched on during an access, they should be switched off when leaving the Hall. Note that the dome lights when switched off cannot be turned back on immediately because they require 10-15 min to cooldown. Do not run more than 60 minutes above 30 nA with 5-pass beam without the beam blocker in front of Faraday cup. Put beam blocker in for long running at high currents for 5 pass operations. Turn DC HV off only for beam tuning; if no beam is available or when beam is stable, keep them on even if you are not taking data. In case of loss of communication with IOCBTARG, follow instructions at https://logbooks.jlab.org/entry/3502218 With any issue contact On-Call Experts or RC - do not spend more than 15-20 min trying to fix the problem. All jscaler iocs (iocjscalerX) on the health screen (under DAQ tab) must be restarted after every DAQ prestart is completed. Check that no unecessary beamline-related screens are open. This includes particularly the big beamline overview screen, but also and any motor/harp/collimator screens, and ioc health screens. Every Shift: Follow run plan as outlined by RC If any concern about beam stability, ask MCC if orbit locks are on (they should be). Keep shift summary up to date in HBLOG. Record all that happens. Check on white board all scalers, strip charts and monitoring plots that need to be logged regularly Document any beam condition change and send scaler GUIs to HBLOG Fill out BTA hourly. Click "Load from EPICS" to automatically fill the left side. Fill and submit the shift checklist in the logbook Perform 2H01A harp scan once per shift or when beam conditions have changed, based on beam monitors (BPMs, halo rates, beam-viewer). During harp scans the HV for DC and HTCC should be OFF. Every Run: Log screenshots of: main scaler GUI display Detector occupancy plots Trigger rate gui Beam strip charts

Webcams Faraday Cup Beam Viewer Tagger Beam Dump Viewer CND CAMAC Crate Hall Fisheye Saclay Cryotarget

Manuals CED Manual MON12 Manual off-line Manual

Epics on the web WebOPI (CUE Login)

Hall-B Operation Safety Procedures Offline Analysis Wiki RCDB

Accelerator Accelerator Whiteboard Program Deputy Shift Plans Run Coordinator Reports

Bluejean meetings Daily analysis meeting 502085879 Daily Run meeting 502085879 RGA Wed meeting 7572697303