Difference between revisions of "Run Group A"

From clas12-run
Jump to navigation Jump to search
Line 118: Line 118:
 
* At 7:00 am MVT expert will come to take a run without gas flow, it will be dedicated run of 15-20 mn-->
 
* At 7:00 am MVT expert will come to take a run without gas flow, it will be dedicated run of 15-20 mn-->
  
−
<font color=blue>''' Controlled Access :'''</font>
 
−
* <s> Fixed BOM Fiber (Stepan, Ben and Nathan)</s>
 
−
* <s> Fixed CND Trigger(Ben & Sergey)</s>
 
−
<font color=blue>''' Prepare For Beam Tuning:'''</font>
 
−
* Make sure the following conditions are established: all CLAS12 detectors are off and target is empty. Call Svt Expert to turn SVT off,  BMT,FMT FTT, FTH are already off then turn HV off all the other detectors. For any problem, consult with the expert-on-call. Following the instructions in the "Establish-physics quality beam" procedure at [https://wiki.jlab.org/clas12-run/images/e/e3/Estab_beam.pdf].
 
−
* Before tuning the beam to the FC, Contact beam line expert to get the OK of the beam quality and the OK to start Moller run
 
−
* Take a Moller run following the precedure in section 5 of the beam line document
 
−
* Then move to next step of the beam tunning to the FC
 
−
* <font color=red>'''Consult with the beamline expert in case of issues or uncerainties'''</font>
 
−
<!--* Establish beam to the tagger yoke first:
 
−
*# ask MCC to energize the tagger dipole magnet and set the current as needed for dumping the beam in the designated dump on the tagger yoke. MCC will ask you to change (set) the beam delivery mode.
 
−
*# position the "blank" collimator on the beam (this is a collimator block, 30 cm long Ni cylinder, without a hole)
 
−
*# when the tagger magnet is at required setting ask MCC if they are ready to deliver beam to the tagger yoke dump (<=5 nA). It may take ~1 hour for MCC to setup and cleanly transport beam to the tagger yoke dump.
 
−
*# perform harp scans using the wire harp at 2C21 girder and 2C24 (tagger harp). Beam profile, peak position, width and signal/background ratio should be like in https://logbooks.jlab.org/entry/3507602 and https://logbooks.jlab.org/entry/3507605. Ask MCC to retune if needed (e.g. beam is too wide or asymmetric or has large tails),repeat the scan after every tune. Iterate to get acceptable beam profile.
 
−
* Send the beam to Faraday Cup dump:
 
−
*# CLAS12 detectors should be OFF, the solenoid magnet current is at 100% (2416 A) its max, torus is at -100% (-3770 A).
 
−
*# ask MCC to degauss and turn the tagger dipole off; while the magnet is being degaussed call the beamline expert (S. Stepanyan) to inform him, you are starting the procedure to send the beam to the Faraday Cup;
 
−
*# position 20 mm collimator on the beam and move "Chromax" screen of the downstream viewer in beam position (if it is not already)
 
−
*# move the beam blocker out: in this configuration beam current readings at 2C24, 2H01 and Faraday Cup should be close.
 
−
*# ask for <= 1 nA, positions, quads settings and rates should be as in https://logbooks.jlab.org/entry/3502404; pay particular attention to halo counter rates: if very different from what shown in the link, call MCC and ask them to verify their settings; note that BOM gains were lowered today and rates should be lower (see https://logbooks.jlab.org/entry/3502559).
 
−
*# make sure beam is stable, beam spot is clearly visible on the Chromax viewer and current does not exceed 1 nA;
 
−
*# repeat harp scans at 2C21, 2C24 (tagger harp) and 2H01: the profile for 2H01 should be as in https://logbooks.jlab.org/entry/3507626. Make sure you select the proper PMT for the analysis. The profile at 2C21 and 2C24 should be as in the scans performed with beam to the tagger magnet yoke dump. If necessary ask MCC to adjust the beam profile at 2H01 to match the previous scan.
 
−
-->
 
−
<font color=blue> Once beam to Faraday Cup is established, prepare to start data taking. Switch on all detectors <font color=red> '''except MM and SVT you need to call the SVT and MM System experts to turn them on'''</font> ask MCC for 5 nA beam check that the rates on the detectors and beam position.Once the beam is stable put beam blocker in ask MCC for to go 50 nA by step of 10 nA checking the rates at each step once the beam is stable at 50 nA and start data taking with empty target for 8 hours 2 hours/run with the RGA trigger elec_htcc_1phe_pcal_300.trg </font> and PROD configuration file.
 
  
 +
<font color=blue>''' Plan for February 13 '''</font>
 +
 +
* Beam estaliched to the FC
 +
* All detector On
 +
* Put beam blocker in
 +
* Ask MCC for 30nA
 +
* Take short run check that all the rates are Ok on all detectos
 +
* Once everything stable ask MCC for 50 nA and start taking data with empty target for 2 hours/run with the RGA trigger configuration elec_htcc_1phe_pcal_300.trg and PROD configuration file.
 +
* At 6 am give the DAQ to Andrea to perform FT Trigger studies
 +
* At 8:30 Bob will fill the target
 +
* At 9:30 once the target is full  Valery, Sergey and Ben will take over to set/adjust the trigger parameter
 +
 +
 +
<!--
 
'''[[Every Shift:]]'''
 
'''[[Every Shift:]]'''
 
*Follow run plan as outlined by RC
 
*Follow run plan as outlined by RC
Line 159: Line 149:
 
* Beam strip charts
 
* Beam strip charts
  
−
 
+
-->
 
| valign=top |
 
| valign=top |
  

Revision as of 01:58, 13 February 2018

[edit]
Role Phone Number
Hall B Run Coordinator (757) 575-7540 (cell)
Hall B Physics Division Liaison (757) 876-1789 (cell)
MCC 7048
Crew Chief 7045
Crew Chief (757) 876-3367 (cell)
Program Deputy (757) 876-7997 (cell)
RadCon (757) 876-1743 (cell)
Gate House Guard 5822
Location Phone Number
Hall B Floor 5165
Hall B Space Frame 5170 and 5171
Hall B Forward Carriage 5371
Hall B Gas Shed 7115
Hall B Counting House 5244 (Shift Expert)
Hall B Counting House (757) 329-4846 (Shift Expert cell)
Hall B Counting House 5245 or 5126 (Shift Worker)
Hall A Counting House 5501
Hall C Counting House 6000
Hall D Counting House 5504
Hall B System Phone Number On-Call Person
Engineering (757) 748-5048 (cell)
(757) 897-9060 (cell)		 Engineering On-Call (primary)
Denny Insley (secondary)
Slow Controls (757) 748-6922 (cell) Nathan Baltzell
Beamline (757) 303-3996 (cell) Eugene Pasyuk
DC (757) 218-4372 (cell)
(757) 748-5048 (cell)		 Florian Hauenstein (primary)
Engineering On-Call (secondary)
SVT/MVT/MM (757) 541-7539 (cell)
(757) 753-7769 (cell)		 Yuri Gotra (primary)
Rafo Paremuzyan (secondary)
ECAL (757) 810-1489 (cell) Cole Smith
FTOF/CTOF/CND (757) 344-7204 (cell) Daniel Carman
ALERT (757) 329-4844 (cell) Raphael Dupré
HTCC/LTCC (757) 344-7174 (cell) Youri Sharabian
FT (757) 344-1848 (cell) Raffaella De Vita
BAND (757) 310-7198 (cell) Florian Hauenstein
RICH (757) 344-3235 (cell)
(757) 748-6922 (cell)		 Christopher Dilks (primary)
Nathan Baltzell (secondary)
DAQ (757) 232-6221 (cell) Sergey Boiarinov
HYDRA (317) 550-9226 (cell) Torri Jeske
Authorized Hall B Solenoid/Torus Operators
Hall B Denny Insley, Morgan Cook, Eugene Pasyuk
Magnet Group Probir Ghosha, Renuka Rajput-Ghoshal
Detector Support Group Brian Eng, Pablo Campero, Tyler Lemon
DC Power Onish Kumar, Sarin Philip
  • Note, all non-JLab numbers must be dialed with an area code. When calling from a counting-house landline, dial "9" first.
  • To call JLab phones from outside the lab, all 4-digit numbers must be preceded by 757-269
  • Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

Click Here to edit Phone Numbers. Note, you then also have to edit this page to force a refresh.


CLAS12 Run Group A, Winter 2018
Beam energy 10.6 GeV (5 pass)
Important: Document all your work in the logbook!
Remember to fill in the run list at the beginning and end of each run (clas12run@gmail.com can fill the run list)

RC: Latifa Elouadrhiri

  • (757) 575-7540
  • 9 575 7540 from Counting Room
  • latifa@jlab.org

PDL: Eugene Pasyuk

  • (757) 876-1789
  • 9 876-1789 from Counting Room
  • pasyuk@jlab.org


  • Note 1: Be very mindful of the background rates in the halo counters, rates in the detectors, and currents in the SVT for all settings to ensure that they are at safe levels.
  • Note 2: At the end of each run, follow the DAQ restart sequence "end run", "abort", "reset", "download", "prestart", "go". After DAQ prestart is complete reboot the scaler IOCs with the command: iocjscalerRestartAll.sh. Note: After each step, make sure it is complete in the Run Control message window. If a roc has crashed, find which one it is and issue a roc_reboot command and try again. Contact the DAQ expert if there are any questions.
  • Note 3: Nominal beam positions: 2C21 (X=0.0 mm, Y=0.0 mm), 2C24 (X=0.0 mm, Y=0.7 mm), 2H01 (X=0.3 mm, Y=-0.6 mm)
  • Note 4: With beam to the Faraday Cup, typical rates on all halo counters upstream from the target should be either 0 or of the order of few counts. Count rates in the range of tens or more may indicate bad beam tune or bleed-through from other Halls.

Run Plan:

(last update 2/12- 12:00)

  • Always monitor the rates on the Hallo counters when they are tunning beam to the other halls
  • Do Not turn on or off SVT only SVT expert can do that


Plan for February 13

  • Beam estaliched to the FC
  • All detector On
  • Put beam blocker in
  • Ask MCC for 30nA
  • Take short run check that all the rates are Ok on all detectos
  • Once everything stable ask MCC for 50 nA and start taking data with empty target for 2 hours/run with the RGA trigger configuration elec_htcc_1phe_pcal_300.trg and PROD configuration file.
  • At 6 am give the DAQ to Andrea to perform FT Trigger studies
  • At 8:30 Bob will fill the target
  • At 9:30 once the target is full Valery, Sergey and Ben will take over to set/adjust the trigger parameter

General Instructions:

  • For a given beam current, compute the FSD thresholds according to the Establish Physics Quality Beam document. Call MCC to update the values. Contact the beamline expert if there are questions about setting the FSD thresholds.
  • The main lights in the Hall (dome lights) and the Forward Carriage lights are being kept off because of light leaks affecting some of the detectors. If these lights are switched on during an access, they should be switched off when leaving the Hall. Note that the dome lights when switched off cannot be turned back on immediately because they require 10-15 min to cooldown.
  • Do not run more than 60 minutes above 30 nA with 5-pass beam without the beam blocker in front of Faraday cup. Put beam blocker in for long running at high currents for 5 pass operations.
  • Turn DC HV off only for beam tuning; if no beam is available or when beam is stable, keep them on even if you are not taking data.
  • In case of loss of communication with IOCBTARG, follow instructions at https://logbooks.jlab.org/entry/3502218
  • With any issue contact On-Call Experts or RC - do not spend more than 15-20 min trying to fix the problem.
  • All jscaler iocs (iocjscalerX) on the health screen (under DAQ tab) must be restarted after every DAQ prestart is completed.
  • Check that no unecessary beamline-related screens are open. This includes particularly the big beamline overview screen, but also and any motor/harp/collimator screens, and ioc health screens.

Every Shift:

  • Follow run plan as outlined by RC
  • If any concern about beam stability, ask MCC if orbit locks are on (they should be).
  • Keep shift summary up to date in HBLOG. Record all that happens.
  • Check on white board all scalers, strip charts and monitoring plots that need to be logged regularly
  • Document any beam condition change and send scaler GUIs to HBLOG
  • Fill out BTA hourly. Click "Load from EPICS" to automatically fill the left side.
  1. Fill and submit the shift checklist in the logbook
  2. Perform 2H01A harp scan once per shift or when beam conditions have changed, based on beam monitors (BPMs, halo rates, beam-viewer). During harp scans the HV for DC and HTCC should be OFF.

'''Every Run:'''

  • Log screenshots of:
  • main scaler GUI display
  • Detector occupancy plots
  • Trigger rate gui
  • Beam strip charts


Clas12design.png

Retrieved from "https://wiki.jlab.org/clas12-run/index.php?title=Run_Group_A&oldid=1089"