Run Group M

[edit]

• Shift Documentation
• Phone Numbers
• Short Term Schedule
• Notes/Known Issues
• Shift Expert
• Remote Worker Shift
• Monitoring
• Useful Links

Shift Schedule ESAD, COO, RSAD Shift Checklist Hot Checkout Beam Time Accounting See guidance at BTA User Guide.

Manuals DC FTOF ECAL LTCC HTCC RICH: Expert Shift CTOF CND SVT MVT MVT turn on procedure FT Beamline Torus Power-Up/Down Procedure Solenoid Power-Up/Down Procedure Target Operation manual DAQ Slow Controls BAND

Procedures Physics-Quality Beam Performing Møller Runs Performing Harp Scans Tunnel/Hall Access ESAD, COO, RSAD

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

If calling local numbers (with area code prefix 757) from the counting room dial 9+[last 7 digits]. To call other area codes dial 91+[ten digit number]

Role Phone Number Hall B Run Coordinator (757) 575-7540 (cell) Hall B Physics Division Liaison (757) 876-1789 (cell) MCC 7048 Crew Chief 7045 Crew Chief (757) 876-3367 (cell) Program Deputy (757) 876-7997 (cell) RadCon (757) 876-1743 (cell) Gate House Guard 5822 Location Phone Number Hall B Floor 5165 Hall B Space Frame 5170 and 5171 Hall B Forward Carriage 5371 Hall B Gas Shed 7115 Hall B Counting House 5244 (Shift Expert) Hall B Counting House (757) 329-4846 (Shift Expert cell) Hall B Counting House 5245 or 5126 (Shift Worker) Hall A Counting House 5501 Hall C Counting House 6000 Hall D Counting House 5504

Hall B System Phone Number On-Call Person Engineering (757) 748-5048 (cell) (757) 897-9060 (cell) Engineering On-Call (primary) Denny Insley (secondary) Slow Controls (757) 748-6922 (cell) Nathan Baltzell Beamline (757) 303-3996 (cell) Eugene Pasyuk DC (757) 218-4372 (cell) (757) 748-5048 (cell) Florian Hauenstein (primary) Engineering On-Call (secondary) SVT/MVT/MM (757) 541-7539 (cell) (757) 753-7769 (cell) Yuri Gotra (primary) Rafo Paremuzyan (secondary) ECAL (757) 810-1489 (cell) Cole Smith FTOF/CTOF/CND (757) 344-7204 (cell) Daniel Carman ALERT (757) 329-4844 (cell) Raphael Dupré HTCC/LTCC (757) 344-7174 (cell) Youri Sharabian FT (757) 344-1848 (cell) Raffaella De Vita BAND (757) 310-7198 (cell) Florian Hauenstein RICH (757) 344-3235 (cell) (757) 748-6922 (cell) Christopher Dilks (primary) Nathan Baltzell (secondary) DAQ (757) 232-6221 (cell) Sergey Boiarinov HYDRA (317) 550-9226 (cell) Torri Jeske Authorized Hall B Solenoid/Torus Operators Hall B Denny Insley, Morgan Cook, Eugene Pasyuk Magnet Group Probir Ghosha, Renuka Rajput-Ghoshal Detector Support Group Brian Eng, Pablo Campero, Tyler Lemon DC Power Onish Kumar, Sarin Philip

• Note, all non-JLab numbers must be dialed with an area code. When calling from a counting-house landline, dial "9" first.
• To call JLab phones from outside the lab, all 4-digit numbers must be preceded by 757-269
• Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

CLAS12 Run Group M, Fall 2021

Beam energies: 2.1, 4.0, 6.0 GeV (1.96 GeV/pass)

RC: Susan Schadmand (phone below) and Sebastian Kuhn (kuhn@jlab.org, 757-639-6640)

• (757) 575-7540
• 9 575 7540 from Counting Room
• susansch@jlab.org

PDL: Valery Kubarovsky

• (757) 876-1789
• 9 876-1789 from Counting Room
• vpk@jlab.org

Run Plan: Jan 26 - Jan 30 2022

Production runs use PROD67_noVTPread and the trigger rgm_6GeV_inb_v1_0.trg .
Run duration 100M events or 4 hours, whichever comes first.

• Presently running on Ar
  • beam blocker calibration (during day)
  • run on Ar target (at least until Saturday)
  • Take at least one run each (4 hours) with 5 nA and 10 nA.
  • run production at 25nA, 1-2 runs with configuration PROD67_PIN_noVTPread

• switch to C target (for about 2 shifts)
  • Check with Bob Miller if we can take data while target is being purged from Ar ->
  • take C data while purging ? Or "empty" target run?

• Sunday afternoon switch to LH2
  • 1 shift LH2
  • beam blocker calibration
  • During Monday owl: 4 hours empty target

• Monday pass change (6GeV beam)
  • OUTLOOK: Run on Ar, Sn and C with 6 GeV beam

DAQ configuration

PROD67_noVTPread , production trigger rgm_6GeV_inb_v1_0.trg .

At the end of each run, follow the STANDARD DAQ RESTART SEQUENCE

• "end run", if the run ended correctly then: "prestart", "go"

• if the run did not end correctly or if any ROCs had to be rebooted:
• "cancel", "reset"
  • "configure", "download", "prestart", "go"
• After each step, make sure it is completed in the Run Control message window. If a ROC has crashed, find which one it is, issue a roc_reboot command ON JUST THAT ROC and try again. Contact the DAQ expert if there are any questions.

References and Standards

(last update 01/18/2022- 23:30)

Nominal Beam Positions

• 2H01, X: -0.6 mm, Y: 0.8 mm
• 2C24, X: -2.0 mm, Y: +0.6 mm

FSD Thresholds

• Upstream: 2000 Hz
• Midstream: 2000 Hz
• Downstream: 500000 Hz
• BOM: 10000
• 5 ms dwell time

Reference Harp Scans for Beam on Faraday Cup: 2H01 [1]

Reference Harp Scans for Beam on Tagger dump: 2C21 [2], tagger harp [3]

Reference Monitoring Histograms (6 nA, production C) [4] Old reference Monitoring Histograms (50 nA, production LD2) [5]

Counter rates

• Upstream counters integrated rates: 0-15 Hz (acceptable up to 100 Hz are acceptable) @50 nA.
• Midstream counters: 10-20 Hz (acceptable up to 50 Hz) @50 nA.
• Counting rates of ~ hundreds of Hz may indicate bad beam tune or bleed-through from other Halls.

Beamline vacuum: should be not higher than 5e-5.

Notes Note 1: The main lights in the Hall (dome lights) and the Forward Carriage lights are being kept off because of light leaks affecting some of the detectors. If these lights are switched on during access, they should be switched off when leaving the Hall. Refer to these photos: ON: [6] OFF: [7] Note that the dome lights when switched off cannot be turned back on immediately because they require 10-15 min to cool down. Note 2: Be very mindful of the background rates in the halo counters, rates in the detectors, and currents in the SVT for all settings to ensure that they are at safe levels. The integrated rates on the upstream counters have to be in the range 0-15 Hz (rates up to 100 Hz are acceptable) and the rates on the midstream counters have to be in the range 10-20 Hz (acceptable up to 50 Hz) @50 nA. Counting rates in the range of hundreds of Hz may indicate a bad beam tune or bleed-through from other Halls. Note 3: When the beam is being delivered to the Faraday Cup: the Fast Shut Down elements: Upstream, Midstream, Downstream, BOM, and Solenoid should always be in the state UNMASKED No changes to the FSD threshold should be made without RC or beamline expert approval Note 4: Do not run more than 30 minutes with >150 W beam to Faraday cup without the beam blocker. Note 5: Any request for a special run or change of configuration has to be approved by the RC & documented Note 6: Do not turn OFF FTOF HVs, even during the beam tune with CW beam (turn off if tuned/pulsed beam in the upstream beamline) Note 7: Turn DC HV off only for beam tuning; if no beam is available or when the beam is stable, keep them on even if you are not taking data. Note 10: Reset CLAS12MON frequently to avoid histogram saturation. Note 11: In case of a Torus and/or Solenoid Fast Dump do the following: Notify MCC to request beam OFF and to drop Hall B status to Power Permit Call Engineering on-call Make a separate log entry with copies to HBTORUS and HBSOLENOID logbooks. In the "Notify" field add Probir Goshal, Dave Kashy, and esr-users@jlab.org Notify Run Coordinator Turn off all detectors Note 12: LTCC is NOT used in this experiment. HV should be kept OFF. Note 13: If responding to RICH or Trigger alarms please post screens also to RICH or HBTRIGGER logbook, respectively.

Known Issues ECAL HV SEC2_WI_E36 is known to be problematic. Channel stays off for now. If any weird stripes appear in the DC occupancy plots, call Sergey. This is a known problem. In case of loss of communication with IOCBTARG, follow instructions at https://logbooks.jlab.org/entry/3502218 Check that no unnecessary beamline-related screens are open. This includes particularly the big beamline overview screen, but also and any motor/harp/collimator screens, and IOC health screens. The error messages " ERR: Event ..." for crates tdcband1, tdcecal1 and tdcecal6 are NOT a problem

Follow the [Short Term Schedule] as outlined by RC includes Run Plan, DAQ configuration, and References and Standards If any concern about beam stability, ask MCC if orbit locks are on (they should be). Keep shift summary up to date in HBLOG. Record all that happens. Document any beam condition change and send scaler GUIs to HBLOG Cycle the FMT gas once per shift, in-between runs. If it is not reset, the interlock may drop and disable the HV. Turning off and on the gas flow without pausing to avoid HV trips. If the HV tripped, make sure that once gas flow is restarted and the flow differential is down to reasonable values, to turn the FMT HV back on and let it ramp all the way up. Remember that this experiment is only using 3 FMT layers, not 6. Do a RICH recovery (press the RICH Recovery button on the GUI) once daily during the day shift between runs. Fill out BTA hourly. Click "Load from EPICS" to automatically fill the left side then correct as needed. In case of other questions or uncertainties of what to do, call the RC or PDL (remote) shift worker: see dedicated Remote Shifts tab above.

Zoom for 24-7 communication with counting house: https://jlab-org.zoomgov.com/j/1619881100 Passcode REQUIRED: 927417 Remind the expert in the counting house to restart their zoom, if necessary Remote VNC connection instructions: https://logbooks.jlab.org/entry/3906039 All necessary applications should be avaible from the desktop menu (left/right click on the desktop) EPICS GUIs should be accessed ONLY via the desktop menu or by running clascss-remote. Remote Demonstration Video (150 MB) Tasks Every Run: WITH BEAM, log screen shots of Beamline Overview In VNC or Web Browser CLAS12 Trigger rates and DAQ status Data Quality Monitoring reset & check spectra frequently upload monitoring plots (mon12) Reference, current, and 5 most recent runs, choose a reference run, here are some choices (the reference numbers refer to logbook entries): ref 6 nA, production C, https://clas12mon.jlab.org/mon12/histograms/?reference=3973807 ref 50 nA, production LD2, https://clas12mon.jlab.org/mon12/histograms/?reference=3943458 Every Shift: Fill the shift checklist log screen shots of RICH temperature and scaler maps Strip charts In VNC or Web Browser: Upstream/Midstream Halo Counters, Downstream Halo Counters, Beam Currents, BPM Positions Alarms If responding to RICH or Trigger alarms please post screens also to RICH or HBTRIGGER logbook, respectively

Backup shifter contact info Name Email Cell phone Justin Estee esteejus@mit.edu Andrew Denniston awild@mit.edu Sara Ratliff ratliff_sara@gwmail.gwu.edu Erin Seroka erinseroka@gwmail.gwu.edu

Webcams Tagger Beam Dump Viewer CND/CTOF Ammeter FTOF/ECAL Ammeter Hall Fisheye Saclay Cryotarget Faraday Cup Beam Viewer To reboot it, run beam-viewer-reboot on a clonpc.

Manuals CED Manual MON12 Manual off-line Manual

Hall Webcams Hall A Hall B Hall C Hall D

Epics on the web Hall B WebOPI (CUE Login) Accelerator (CUE Login)

Live Monitoring Links CLAS12 Monitoring Timelines Live Charge Collected Plots Live Luminosity Collected Plots

Hall-B Operation Safety Procedures Run Group M Analysis Wiki RCDB CLAS12 mon page Comparison between mon12 histograms (last 5 runs) Accumulated Charge Accumulated datasize Run Coordinator Schedule Target and Run Plan Summary Full Run Plan Run lists

Accelerator Accelerator Whiteboard Program Deputy Shift Plans Run Coordinator Reports Beam Time Accounting Reports References Proposal

ZOOM meetings 07:45 RC/PD Morning Meeting 08:00 MCC/OPS Morning Meeting 15:30 Daily RC Meeting Zoom Link Meeting ID: 161 269 7153 Passcode: 474207 On site - CEBAF Center F324-325 conference room Daily Analysis Meeting to follow directly after Meeting Agendas