Difference between revisions of "Cables"
| Line 20: | Line 20: | ||
The HV and the anode signals of each column of the detector is routed through a PCB board. This boards also holds one LED per channel. | The HV and the anode signals of each column of the detector is routed through a PCB board. This boards also holds one LED per channel. | ||
| − | * Each HV cable is | + | * Each HV cable is plugged into a [https://www.fischerconnectors.com/sites/default/files/specifications/tech_specs_full_1.7_oct17.pdf Fischer D 102 A018 connector] on the PCB board |
* The anode cable is plugged into a [https://www.digikey.com/product-detail/en/cinch-connectivity-solutions-johnson/142-0701-501/J569-ND/241109 SMA CINCH CONNECTIVITY 142-0701-501] | * The anode cable is plugged into a [https://www.digikey.com/product-detail/en/cinch-connectivity-solutions-johnson/142-0701-501/J569-ND/241109 SMA CINCH CONNECTIVITY 142-0701-501] | ||
| − | * The anode signal gets out at the opposite side of the board | + | * The anode signal gets out at the opposite side of the board through an identical connector [https://www.digikey.com/product-detail/en/cinch-connectivity-solutions-johnson/142-0701-501/J569-ND/241109 SMA CINCH CONNECTIVITY 142-0701-501] |
* The HV enters through [https://wiki.jlab.org/cuawiki/images/c/ca/SAMTEC-pmsdx-xx-xxxx-x-xx.xx-x-xxx-mkt.pdf 2 SAMTEC PMSD-15-206-K-D-LUS and 1 PMSD-08-206-K-D-LUS] connectors | * The HV enters through [https://wiki.jlab.org/cuawiki/images/c/ca/SAMTEC-pmsdx-xx-xxxx-x-xx.xx-x-xxx-mkt.pdf 2 SAMTEC PMSD-15-206-K-D-LUS and 1 PMSD-08-206-K-D-LUS] connectors | ||
* The LED sitting in front of each PMT are controlled by a ribbon cable plugged at the bottom of the board to male 2x36-pin SAMTEC connector [https://www.samtec.com/products/tst-136-01-l-d TST-136-01-L-D] | * The LED sitting in front of each PMT are controlled by a ribbon cable plugged at the bottom of the board to male 2x36-pin SAMTEC connector [https://www.samtec.com/products/tst-136-01-l-d TST-136-01-L-D] | ||
| Line 59: | Line 59: | ||
=== Signal panel (LEMO) === | === Signal panel (LEMO) === | ||
| − | This is not | + | This is not patch panel per se, but a simple panel with holes where the [https://www.lemo.com/pdf/PES.00.250.NTME31.pdf LEMOS]of the [https://wiki.jlab.org/cuawiki/index.php/Cables#Anode_signal_cables anode cables] are mounted on. |
=== HV panel === | === HV panel === | ||
Revision as of 11:42, 25 August 2020
Overview
Voltage divider
- Voltage divider schematics
- The 5-pin connector on the voltage divider is Samtec Part # IPL1-105-01-L-S-RA-K (male):
- Pictures of the assembly:
Custom cable from voltage divider to PCB boards
The cable has a female SAMTEC 5-pin connector IPD1-05-S-K on one side, with 4 crimp contacts CC79L-2630-01-L. On the other side the cable has a SMA RS PRO 546-3210 connector (Datasheet, Crimp instructions) and Fischer connector S 102 A 018. Both the HV and the anode cables are KX3A type and 3-mm external diameter. The cable length is 375 mm.
- Cable schematics
- Picture of the cable:
PCB boards (one per detector column)
The HV and the anode signals of each column of the detector is routed through a PCB board. This boards also holds one LED per channel.
- Each HV cable is plugged into a Fischer D 102 A018 connector on the PCB board
- The anode cable is plugged into a SMA CINCH CONNECTIVITY 142-0701-501
- The anode signal gets out at the opposite side of the board through an identical connector SMA CINCH CONNECTIVITY 142-0701-501
- The HV enters through 2 SAMTEC PMSD-15-206-K-D-LUS and 1 PMSD-08-206-K-D-LUS connectors
- The LED sitting in front of each PMT are controlled by a ribbon cable plugged at the bottom of the board to male 2x36-pin SAMTEC connector TST-136-01-L-D
- Board schematics: Layout.pdf, Connections.pdf, Parts.xlsx
HV ribbon cables
The PCB and the HV panel are connected by 20 AWG cables. Three cables per detector column: 2 cables have SAMTEC PMSD-15-206-K-15.40-D-LUS connectors and 1 cable has PMSD-08-206-K-15.40-D-LUS connectors
Notice that 20 AWG = 7.2 A, and our currents are of the order of micro-Amps.
LED control cables
Ribbon cables with SAMTEC connectors HCSD-36-01-N on each side:
Anode signal cables
- Signal come out at the back of the PCB boards.
- There are KX3 cables with a SMA connector RS PRO 546-3210 on one side and a panel-mount LEMO PES.00.250.NTME31.
- The length of each cable depends on the row of the detector (longer cables for channels at the bottom).
- The LEMO connectors are mounted at the top of the NPS box (see LEMO panel below)
- Cable schematics
Patch panels at the top of the NPS box
There are 3 panels of the top of the NPS box:
Signal panel (LEMO)
This is not patch panel per se, but a simple panel with holes where the LEMOSof the anode cables are mounted on.
HV panel
The HV panel has 2 SAMTEC connectors PMSD-15-206-K-D-LUS and 1 SAMTEC connector PMSD-08-206-K-D-LUS per detector column (a total of 30 columns).
The board is made of two 15-pin SAMTEC IPBT-115-H1-T-D-K and one 8-pin SAMTEC IPBT-108-H1-T-D-K for each detector column (associated with one PCB board)
- Board schematics Layout.pdf, Connections.pdf, Parts.xlsx
- Input connectors
LED panel
Made of SAMTEC connectors HCSD-36-D-86.60-01-N-G (one per detector column, i.e. a total of 30)
- Board schematics: Layout, Connections.pdf, Parts.xlsx