Difference between revisions of "Install an EJFAT Load Balancer"

From epsciwiki
Jump to navigation Jump to search
 
(21 intermediate revisions by the same user not shown)
Line 41: Line 41:
 
| Lab || 57755 || xilinx-labtools-docker || 977a5678
 
| Lab || 57755 || xilinx-labtools-docker || 977a5678
 
|-
 
|-
−
| DPDK || 57593 || smartnic-dpdk-docker || xxxxxxxx
+
| DPDK || 57593 || smartnic-dpdk-docker || fd1ea53
 
|}
 
|}
  
−
=== Xilinx Supports tools: ===
+
== Xilinx Supports tools: ==
−
==== Required Binaries ====
+
=== Required Binaries ===
 
<pre>
 
<pre>
 
cp /daqfs/ejfat/Downloads/xilinx/Vivado_Lab_Lin_2023.2_1013_2256.tar.gz  ~/esnet/xilinx-labtools-docker/vivado-installer/  
 
cp /daqfs/ejfat/Downloads/xilinx/Vivado_Lab_Lin_2023.2_1013_2256.tar.gz  ~/esnet/xilinx-labtools-docker/vivado-installer/  
Line 52: Line 52:
 
</pre>
 
</pre>
  
−
==== Docker build for Xilinx Labtools: ====
+
=== Docker build for Xilinx Labtools: ===
 
<pre>
 
<pre>
 
cd ~/esnet/xilinx-labtools-docker
 
cd ~/esnet/xilinx-labtools-docker
Line 78: Line 78:
 
</pre>
 
</pre>
  
−
Follow instructions in README.md  
+
Follow instructions in README.md
−
 
 
  
−
=== Docker build for DPDK: ===
+
== Docker build for DPDK: ==
 
<pre>
 
<pre>
 
cd ~/esnet/smartnic-dpdk-docker  
 
cd ~/esnet/smartnic-dpdk-docker  
  
−
git checkout xxxxxxxx
+
git checkout fd1ea53
 
</pre>
 
</pre>
  
−
Follow instructions in README.md  
+
Follow instructions in README.md
−
 
 
  
−
=== Docker build for smartnic: ===
+
== Docker build for smartnic: ==
 
<pre>
 
<pre>
 
cd ~/esnet/esnet-smartnic-fw  
 
cd ~/esnet/esnet-smartnic-fw  
Line 125: Line 123:
  
  
−
==== Modifiy the .env file: ====
+
=== Modifiy the .env file: ===
  
 
<pre>
 
<pre>
Line 186: Line 184:
 
==== Un-remark and set the FPGA PCI device code: ====
 
==== Un-remark and set the FPGA PCI device code: ====
  
−
Execute the bash cmds either
+
Execute the bash cmd:
−
<pre>
 
−
lspci -Dd 10ee:  
 
−
</pre>
 
−
 
 
−
or
 
−
 
 
 
<pre>
 
<pre>
−
lspci |grep -i xilinx
+
FPDC=`lspci -Dd 10ee:|head -1|tr -s ' '|cut -f1 -d' '|cut -f1 -d'.'`
 
</pre>
 
</pre>
  
Line 200: Line 192:
  
 
<pre>
 
<pre>
−
FPGA_PCIE_DEV=0000:a1:00
+
FPGA_PCIE_DEV=$FPDC
 
</pre>
 
</pre>
  
Line 207: Line 199:
  
 
<pre>
 
<pre>
−
SN_HOST=ejfat-?-dp.jlab.org          #Note this is the data planes (FPGA) well known IPV4 address or network name  
+
SN_HOST=${HOSTNAME}-dp.jlab.org          #Note this is the data planes (FPGA) well known IPV4 address or network name  
 
</pre>
 
</pre>
  
Line 215: Line 207:
  
 
<pre>
 
<pre>
−
openssl rand -base64 24  
+
AUTH=`openssl rand -base64 24`
 
</pre>
 
</pre>
  
 
e.g., 1CEpuDN0z39AFndEvcP3EmsuT8zu+3lt  
 
e.g., 1CEpuDN0z39AFndEvcP3EmsuT8zu+3lt  
 
<pre>
 
<pre>
−
SN_CFG_AUTH_TOKEN=1CEpuDN0z39AFndEvcP3EmsuT8zu+3lt
+
SN_CFG_AUTH_TOKEN=$AUTH
 
</pre>
 
</pre>
  
−
==== 5.3 Modify the sn-stack/docker-compose.yml file: ====
+
==== Modify the sn-stack/docker-compose.yml file: ====
 +
 
 +
In the smartnic-hw/command: section, uncomment the FORCE argument line in the /scripts/program_card.sh invocation:
  
−
In the smartnic-hw/command: section, uncomment the FORCE argument line in the /scripts/program_card.sh invocation
+
<pre>
 +
    command:
 +
      - /bin/bash
 +
      - -c
 +
      - -e
 +
      - -o
 +
      - pipefail
 +
      - -x
 +
      - |
 +
        if [ ! -e /bitfiles/ok ] ; then
 +
          exit 1
 +
        fi
 +
        /scripts/program_card.sh \
 +
          xilinx-hwserver:3121 \
 +
          "${HW_TARGET_SERIAL:-*}" \
 +
          /bitfiles/esnet-smartnic.bit \
 +
          $FPGA_PCIE_DEV \
 +
          FORCE                          #### <- ###################
 +
        if [ $$? ] ; then
 +
          touch /status/ok
 +
          sleep infinity
 +
        fi
 +
</pre>
  
 
In older configurations it is required to expose TCP port 50051 (smartnic-p4) outside of the *firmware* docker stack so that the external control plane can reach the p4 agent. This is needed for retro-fitting  older firmware with the newer FW / control-plane split. Newer firmware doesn't need this port fixup.  
 
In older configurations it is required to expose TCP port 50051 (smartnic-p4) outside of the *firmware* docker stack so that the external control plane can reach the p4 agent. This is needed for retro-fitting  older firmware with the newer FW / control-plane split. Newer firmware doesn't need this port fixup.  
Line 246: Line 262:
  
 
=== Verify the sn-stack/docker-compose.yml: ===
 
=== Verify the sn-stack/docker-compose.yml: ===
−
 
+
<pre>
 
cd sn-stack  
 
cd sn-stack  
  
 
docker compose config --quiet && echo "All good!"  
 
docker compose config --quiet && echo "All good!"  
 +
</pre>
  
−
 
+
If applicable, follow instructions in esnet-smartnic-fw/sn-stack/README.INSTALL.md for: One-Time setup:  
−
# 5.4 If applicable, follow instructions in esnet-smartnic-fw/sn-stack/README.INSTALL.md for: One-Time setup:  
 
 
   
 
   
−
# 5.4.1  Converting from factory flash image to ESnet Smartnic flash image  
+
Converting from factory flash image to ESnet Smartnic flash image  
 
   
 
   
−
# 5.4.2  Perform a cold-boot (power cycle) of the server hosting the FPGA card  
+
Perform a cold-boot (power cycle) of the server hosting the FPGA card  
 +
 
 +
It is essential that this is a proper power cycle and not simply a warm reboot. Specifically do not use 
 +
<pre>
 +
shutdown -r now 
 +
</pre>
  
−
# It is essential that this is a proper power cycle and not simply a warm reboot. Specifically do not use 
+
Instead
−
+
<pre>
−
# $ shutdown -r now 
+
shutdown -P  
−
   
+
</pre>
−
# Remotely: (smokenmirrors)
 
  
−
ipmitool -I lanplus -U ejfat -L Operator -H ejfat-4-bmc.jlab.org chassis power status
+
then (Remotely): (smokenmirrors)
−
ipmitool -I lanplus -U ejfat -L Operator -H ejfat-4-bmc.jlab.org chassis power off
 
−
ipmitool -I lanplus -U ejfat -L Operator -H ejfat-4-bmc.jlab.org chassis power on
 
  
−
# Failure to perform a cold-boot here will result in an unusable card.  
+
<pre>
 +
ipmitool -I lanplus -U ejfat -L Operator -H $HOSTNAME-bmc.jlab.org chassis power status
 +
ipmitool -I lanplus -U ejfat -L Operator -H $HOSTNAME-bmc.jlab.org chassis power on
 +
</pre>
  
 +
Failure to perform a cold-boot here will result in an unusable card.
  
−
# 5.4.3  Normal Operation of the Runtime Environment
 
  
 +
Normal Operation of the Runtime Environment:
 +
<pre>
 
docker compose up -d
 
docker compose up -d
 +
</pre>
  
−
# Verify that  
+
Verify that  
−
+
<pre>
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw sn-cli dev version  
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw sn-cli dev version  
 +
</pre>
 +
 +
Returns something like:
 
   
 
   
−
# Returns something like:
+
Device Version Info  
−
+
        DNA:          0x40020000013b83c12c108485  
−
# Device Version Info  
+
        USR_ACCESS:    0x0000ac1b (57684)  
−
 
+
        BUILD_STATUS:  0x12211043  
−
#        DNA:          0x40020000013b83c12c108485  
 
−
 
 
−
#        USR_ACCESS:    0x0000ac1b (<version>>)  
 
−
 
 
−
#        BUILD_STATUS:  0x12211043  
 
−
 
 
  
 +
<pre>
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  logs smartnic-fw
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  logs smartnic-fw
 +
</pre>
  
−
# Returns something like:  
+
Returns something like:  
  
−
# smartnic-fw-1  | + sleep infinity
+
smartnic-fw-1  | + sleep infinity
−
 
 
−
 
 
−
# 6. Library build for ersap-grpc :
 
  
 +
== Library build for ersap-grpc ==
 +
<pre>
 
cd ~/esnet/ersap-grpc/
 
cd ~/esnet/ersap-grpc/
  
Line 305: Line 327:
  
 
export GRPC_INSTALL_DIR=/daqfs/ersap/installation3
 
export GRPC_INSTALL_DIR=/daqfs/ersap/installation3
 +
</pre>
  
−
# Follow instructions in README.md  
+
Follow instructions in README.md  
  
−
# Note: It is typically not necessary to install/build grpc as the line above indicates
+
Note: It is typically not necessary to install/build grpc as the line above indicates
−
 
 
−
# 7. Docker build for Control Plane:
 
  
 +
== Docker build for Control Plane: ==
 +
<pre>
 
cd ~/esnet/udplbd/
 
cd ~/esnet/udplbd/
  
Line 317: Line 340:
  
 
cp /daqfs/ejfat/Downloads/JLab/JLabCA.crt ~/esnet/udplbd/
 
cp /daqfs/ejfat/Downloads/JLab/JLabCA.crt ~/esnet/udplbd/
 +
</pre>
  
−
# 7.1 Modifiy docker-compose.yml
+
=== Modifiy docker-compose.yml ===
−
 
 
−
# a. Mount host filespace for /data
 
  
 +
Mount host filespace for /data
 +
<pre>
 
services:
 
services:
 
   volumes:
 
   volumes:
 
     - ./data:/data
 
     - ./data:/data
 +
</pre>
  
−
# b. Mount host TLS cert location for /certs
+
Mount host TLS cert location for /certs
−
 
+
<pre>
 
services:
 
services:
 
   volumes:
 
   volumes:
 
     - /etc/letsencrypt/archive/<machine>.jlab.org:/certs
 
     - /etc/letsencrypt/archive/<machine>.jlab.org:/certs
 +
</pre>
  
−
# 7.2 remove the leftover udplbd data base file:
+
remove the leftover udplbd data base file:
−
 
+
<pre>
 
rm ~/esnet/udplbd/data/udplbd.db
 
rm ~/esnet/udplbd/data/udplbd.db
 +
</pre>
  
−
# 7.3 Follow instructions in README.md  
+
Follow instructions in README.md  
  
−
# 7.3a Modifiy /etc/config.yml
+
=== Modifiy /etc/config.yml ===
−
 
+
<li> specify FPGA DP IPV4/6 addresses (up to 8)
−
# a. specify FPGA DP IPV4/6 addresses (up to 8)
+
<li> specify FPGA DP MAC unicast/broadcast addresses
−
# b. specify FPGA DP MAC unicast/broadcast addresses
+
<li> Put host IPV4 for CP event numbers/host (sync)
−
# c. Put host IPV4 for CP event numbers/host (sync)
+
<li> Specify an event number/port for each address in 7.3a.a
−
# d. Specify an event number/port for each address in 7.3a.a
+
<li> Put host IPV4 for CP server/host (grpc)
−
# e. Put host IPV4 for CP server/host (grpc)
+
<li> Specify an auth token for CP grpc comms
−
# f. Specify an auth token for CP grpc comms
+
<li> optionally enable server/TLS
−
# g. optionally enable server/TLS
+
<li> optionally specify container path to server/tls/certFile and server/tls/keyFile
−
# h. optionally specify container path to server/tls/certFile and server/tls/keyFile
+
<li> optionally perform steps 7.3a.g-h for smartnic/tls
−
# i. optionally perform steps 7.3a.g-h for smartnic/tls
 
  
 +
<pre>
 
docker compose build
 
docker compose build
 
docker compose up -d
 
docker compose up -d
−
 
−
# 7.4
 
−
 
 
docker compose -f ~/esnet/udplbd/docker-compose.yml  logs udplbd | less
 
docker compose -f ~/esnet/udplbd/docker-compose.yml  logs udplbd | less
 +
</pre>
  
−
 
+
== Execute the the FPGA cmac setup procedure ==
−
# 8. Execute the the FPGA cmac setup procedure
+
<pre>
−
 
+
cp /daqfs/efat/Downloads/esnet/u280_cmac_setup.sh ~/esnet/esnet-smartnic-fw/sn-stack/scratch
−
scp <somewhere>/u280_cmac_setup.sh ~/esnet/esnet-smartnic-fw/sn-stack/scratch
 
  
 
chmod +x ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.sh
 
chmod +x ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.sh
  
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw /scratch/u280_cmac_setup.sh > ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.out
 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw /scratch/u280_cmac_setup.sh > ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.out
 +
</pre>

Latest revision as of 14:56, 15 November 2024

New Installation Preparations

Check for stale docker images:

docker image ls

Delete images with tags: esnet-smartnic-fw, smartnic-dpdk-docker, xilinx-labtools-docker, udplbd

Initial setup:

mkdir ~/esnet 

cd ~/esnet 

git clone --recursive https://github.com/esnet/xilinx-labtools-docker 

git clone --recursive https://github.com/esnet/smartnic-dpdk-docker 

git clone --recursive https://github.com/esnet/esnet-smartnic-fw 

git clone https://github.com/JeffersonLab/ersap-grpc.git

git clone https://github.com/esnet/udplbd.git

Proper revisions:

Stable Lineup
Purpose Version Container Revision
HW 57684 udplb c6956b46
FW 58131 esnet-smartnic-fw a07943f0
SW 0.3.2 udplbd 5712d10
Lab 57755 xilinx-labtools-docker 977a5678
DPDK 57593 smartnic-dpdk-docker fd1ea53

Xilinx Supports tools:

Required Binaries

cp /daqfs/ejfat/Downloads/xilinx/Vivado_Lab_Lin_2023.2_1013_2256.tar.gz  ~/esnet/xilinx-labtools-docker/vivado-installer/ 
cp /daqfs/ejfat/Downloads/xilinx/loadsc_v2.3.zip                         ~/esnet/xilinx-labtools-docker/sc-fw-downloads 
cp /daqfs/ejfat/Downloads/esnet/SC_U280_4_3_31.zip                       ~/esnet/xilinx-labtools-docker/sc-fw-downloads

Docker build for Xilinx Labtools:

cd ~/esnet/xilinx-labtools-docker

git checkout 977a5678

Remark out the following lines in Dockerfile: 

# Download and extract a few versions of the Satellite Controller firmware packages
#   https://www.xilinx.com/support/download/index.html/content/xilinx/en/downloadNav/alveo.html
# ARG SC_FW_BASE_URL="https://www.xilinx.com/bin/public/openDownload?filename="
# ARG SC_FW_U280_PKGS="xilinx-u280-gen3x16-xdma_2023.1_2023_0507_2220-all.deb.tar.gz xilinx-u280-gen3x16-xdma_2022.1_2022_0804_1110-all.deb.tar.gz"
# ARG SC_FW_U55C_PKGS="xilinx-u55c-gen3x16-xdma_2023.1_2023_0507_2220-all.deb.tar.gz xilinx-u55c-gen3x16-xdma_2022.1_2022_0415_2123-all.deb.tar.gz"
# RUN \
#   cd /sc-fw-downloads && \
#   for f in $SC_FW_U280_PKGS $SC_FW_U55C_PKGS ; do \
#     echo "Fetching: $SC_FW_BASE_URL$f" ; \
#     wget -qO- "$SC_FW_BASE_URL$f" | tar xz --wildcards 'xilinx-sc-fw*.deb' ; \
#   done ; \
#   mkdir -p /sc-fw && \
#   for sc in /sc-fw-downloads/xilinx-sc-fw*.deb ; do \
#     dpkg-deb --fsys-tarfile "$sc" | tar x -C /sc-fw --strip-components 6 --wildcards './opt/xilinx/firmware/sc-fw/*/sc-fw-*.txt' ; \
#   done

Follow instructions in README.md

Docker build for DPDK:

cd ~/esnet/smartnic-dpdk-docker 

git checkout fd1ea53

Follow instructions in README.md

Docker build for smartnic:

cd ~/esnet/esnet-smartnic-fw 

git checkout a07943f0

The ejfat f/w is engineered and obtained from ESnet as an artifacts file: 

SN_HW_VER=57684
SN_HW_APP_NAME=udplb

cp /daqfs/ejfat/Downloads/esnet/artifacts.au280.$SN_HW_APP_NAME.$SN_HW_VER.zip ~/esnet/esnet-smartnic-fw/sn-hw

Follow instructions in README.md up to and including (if necessary) the following lines: 

mkdir -p ~/.docker/cli-plugins/
curl -SL https://github.com/docker/compose/releases/download/v2.27.1/docker-compose-linux-x86_64 -o ~/.docker/cli-plugins/docker-compose
chmod +x ~/.docker/cli-plugins/docker-compose

update cloned repo:

git submodule init 

git submodule update


Modifiy the .env file:

cp example.env .env

The following .env var lines must be populated:

Note that Docker images can be retrieved from a remote es.net repository or retrieval will instead be made from a local Docker repository. 

SMARTNIC_DPDK_IMAGE_URI=<REPOSITORY:TAG>

Similarly, 

LABTOOLS_IMAGE_URI=<REPOSITORY:TAG>

Un-remark and set the following lines: 

SN_HW_APP_NAME=udplb 

SN_HW_BOARD=au280 

SN_HW_VER=57684    

SN_FW_VER=44124       #Note this value is useful but not critical; can be set to zero


5.1 Build the firmware:

./build.sh

Modify the sn-stack/.env file:

Un-remark and set the following lines: 

COMPOSE_PROFILES=smartnic-mgr-vfio-unlock

Un-remark and set the JTag serial code:

Execute the bash cmd: 

SER=`sudo lsusb -v -d 0403:6011 | grep iSerial|tr -s ' '|cut -f4 -d' '`

e.g., 21770323600G 

HW_TARGET_SERIAL=${SER}A   #Note the appended 'A' char

Un-remark and set the FPGA PCI device code:

Execute the bash cmd: 

FPDC=`lspci -Dd 10ee:|head -1|tr -s ' '|cut -f1 -d' '|cut -f1 -d'.'`

e.g., 0000:a1:00 

FPGA_PCIE_DEV=$FPDC


Un-remark and set the following lines: 

SN_HOST=${HOSTNAME}-dp.jlab.org          #Note this is the data planes (FPGA) well known IPV4 address or network name

Un-remark and set the rpc AUTH token:

Execute the bash cmd: 

AUTH=`openssl rand -base64 24`

e.g., 1CEpuDN0z39AFndEvcP3EmsuT8zu+3lt 

SN_CFG_AUTH_TOKEN=$AUTH

Modify the sn-stack/docker-compose.yml file:

In the smartnic-hw/command: section, uncomment the FORCE argument line in the /scripts/program_card.sh invocation: 

    command:
      - /bin/bash
      - -c
      - -e
      - -o
      - pipefail
      - -x
      - |
        if [ ! -e /bitfiles/ok ] ; then
          exit 1
        fi
        /scripts/program_card.sh \
          xilinx-hwserver:3121 \
          "${HW_TARGET_SERIAL:-*}" \
          /bitfiles/esnet-smartnic.bit \
          $FPGA_PCIE_DEV \
          FORCE                           #### <- ###################
        if [ $$? ] ; then
          touch /status/ok
          sleep infinity
        fi

In older configurations it is required to expose TCP port 50051 (smartnic-p4) outside of the *firmware* docker stack so that the external control plane can reach the p4 agent. This is needed for retro-fitting older firmware with the newer FW / control-plane split. Newer firmware doesn't need this port fixup.

Exposing the p4 agent TCP port is done by adding this stanza to the "smartnic-p4" section: 

 
    ports: 
      - "50051:50051"

add the following lines to the end of the smartnic-p4: section: 

 

    logging: 
      options: 
        max-file: 5 
        max-size: 100m

Verify the sn-stack/docker-compose.yml:

cd sn-stack 

docker compose config --quiet && echo "All good!"

If applicable, follow instructions in esnet-smartnic-fw/sn-stack/README.INSTALL.md for: One-Time setup:

Converting from factory flash image to ESnet Smartnic flash image

Perform a cold-boot (power cycle) of the server hosting the FPGA card

It is essential that this is a proper power cycle and not simply a warm reboot. Specifically do not use 

 
shutdown -r now

Instead 

 
shutdown -P

then (Remotely): (smokenmirrors) 

ipmitool -I lanplus -U ejfat -L Operator -H $HOSTNAME-bmc.jlab.org chassis power status
ipmitool -I lanplus -U ejfat -L Operator -H $HOSTNAME-bmc.jlab.org chassis power on

Failure to perform a cold-boot here will result in an unusable card.


Normal Operation of the Runtime Environment: 

docker compose up -d

Verify that 

 
docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw sn-cli dev version

Returns something like:

Device Version Info 

        DNA:           0x40020000013b83c12c108485 
        USR_ACCESS:    0x0000ac1b (57684) 
        BUILD_STATUS:  0x12211043 

docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  logs smartnic-fw

Returns something like:

smartnic-fw-1 | + sleep infinity

Library build for ersap-grpc

cd ~/esnet/ersap-grpc/

git switch  esnet3
git checkout a3b85c3868554380e12759f23335eaf3fead2441

export GRPC_INSTALL_DIR=/daqfs/ersap/installation3

Follow instructions in README.md

Note: It is typically not necessary to install/build grpc as the line above indicates

Docker build for Control Plane:

cd ~/esnet/udplbd/

git checkout 5712d10

cp /daqfs/ejfat/Downloads/JLab/JLabCA.crt ~/esnet/udplbd/

Modifiy docker-compose.yml

Mount host filespace for /data 

services:
  volumes:
    - ./data:/data

Mount host TLS cert location for /certs 

services:
  volumes:
    - /etc/letsencrypt/archive/<machine>.jlab.org:/certs

remove the leftover udplbd data base file: 

rm ~/esnet/udplbd/data/udplbd.db

Follow instructions in README.md

Modifiy /etc/config.yml

  • specify FPGA DP IPV4/6 addresses (up to 8)
  • specify FPGA DP MAC unicast/broadcast addresses
  • Put host IPV4 for CP event numbers/host (sync)
  • Specify an event number/port for each address in 7.3a.a
  • Put host IPV4 for CP server/host (grpc)
  • Specify an auth token for CP grpc comms
  • optionally enable server/TLS
  • optionally specify container path to server/tls/certFile and server/tls/keyFile
  • optionally perform steps 7.3a.g-h for smartnic/tls 
    docker compose build
docker compose up -d
docker compose -f ~/esnet/udplbd/docker-compose.yml  logs udplbd | less

    Execute the the FPGA cmac setup procedure

    cp /daqfs/efat/Downloads/esnet/u280_cmac_setup.sh ~/esnet/esnet-smartnic-fw/sn-stack/scratch

chmod +x ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.sh

docker compose -f ~/esnet/esnet-smartnic-fw/sn-stack/docker-compose.yml  exec smartnic-fw /scratch/u280_cmac_setup.sh > ~/esnet/esnet-smartnic-fw/sn-stack/scratch/u280_cmac_setup.out
    • Retrieved from "https://wiki.jlab.org/epsciwiki/index.php?title=Install_an_EJFAT_Load_Balancer&oldid=5828"