Run Group A

[edit]

• Shift Documentation
• Phone Numbers
• Short Term Schedule
• Monitoring
• Useful Links

Shift Schedule Shift Checklist Hot Checkout Beam Time Accounting See guidance for BTA in Beam Time Accounting User Guide.

Manuals DC FTOF ECAL LTCC HTCC RICH: expert novice CTOF CND SVT MVT MVT turn on procedure FT Beamline Torus Power-Up and Power-Down Procedure Solenoid Power-Up and Power-Down Procedure Cryo Target Operation manual DAQ Slow Controls

Procedures Establishing Physics-Quality Beam Performing Møller Runs (Old) Performing Harp Scans Tunnel/Hall Access

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

If calling local numbers (with area code prefix 757) from the counting room dial 9+[last 7 digits]. To call other area codes dial 91+[10 digit number]

Role Phone Number Hall B Run Coordinator (757) 575-7540 (cell) Hall B Physics Division Liaison (757) 876-1789 (cell) MCC 7048 Crew Chief 7045 Crew Chief (757) 876-3367 (cell) Program Deputy (757) 876-7997 (cell) RadCon (757) 876-1743 (cell) Gate House Guard 5822 Location Phone Number Hall B Floor 5165 Hall B Space Frame 5170 and 5171 Hall B Forward Carriage 5371 Hall B Gas Shed 7115 Hall B Counting House 5244 (Shift Expert) Hall B Counting House (757) 329-4846 (Shift Expert cell) Hall B Counting House 5245 or 5126 (Shift Worker) Hall A Counting House 5501 Hall C Counting House 6000 Hall D Counting House 5504

Hall B System Phone Number On-Call Person Engineering (757) 748-5048 (cell) (757) 897-9060 (cell) Engineering On-Call (primary) Denny Insley (secondary) Slow Controls (757) 748-6922 (cell) Nathan Baltzell Beamline (757) 303-3996 (cell) Eugene Pasyuk DC (757) 218-4372 (cell) (757) 748-5048 (cell) Florian Hauenstein (primary) Engineering On-Call (secondary) SVT/MVT/MM (757) 541-7539 (cell) (757) 753-7769 (cell) Yuri Gotra (primary) Rafo Paremuzyan (secondary) ECAL (757) 810-1489 (cell) Cole Smith FTOF/CTOF/CND (757) 344-7204 (cell) Daniel Carman ALERT (757) 329-4844 (cell) Raphael Dupré HTCC/LTCC (757) 344-7174 (cell) Youri Sharabian FT (757) 344-1848 (cell) Raffaella De Vita BAND (757) 310-7198 (cell) Florian Hauenstein RICH (757) 344-3235 (cell) (757) 748-6922 (cell) Christopher Dilks (primary) Nathan Baltzell (secondary) DAQ (757) 232-6221 (cell) Sergey Boiarinov HYDRA (317) 550-9226 (cell) Torri Jeske Authorized Hall B Solenoid/Torus Operators Hall B Denny Insley, Morgan Cook, Eugene Pasyuk Magnet Group Probir Ghosha, Renuka Rajput-Ghoshal Detector Support Group Brian Eng, Pablo Campero, Tyler Lemon DC Power Onish Kumar, Sarin Philip

• Note, all non-JLab numbers must be dialed with an area code. When calling from a counting-house landline, dial "9" first.
• To call JLab phones from outside the lab, all 4-digit numbers must be preceded by 757-269
• Click Here to edit Phone Numbers. Note, you then also have to edit the current page to force a refresh.

Click Here to edit Phone Numbers. Note, you then also have to edit this page to force a refresh.

CLAS12 Run Group A, Fall 2018
Beam energy 10.6 GeV (5 pass)
Important: Document all your work in the logbook!
Remember to fill in the run list at the beginning and end of each run

RC: Stepan Stepanyan

• (757) 575-7540
• 9 575 7540 from Counting Room
• markov@jlab.org

PDL: Eugene Pasyuk

• (757) 876-1789
• 9 876-1789 from Counting Room
• pasyuk@jlab.org

• Note 1: Be very mindful of the background rates in the halo counters, rates in the detectors, and currents in the SVT for all settings to ensure that they are at safe levels.

The integrated rates on the upstream counters have to be in the range 0-15 Hz (rates up 100 Hz are acceptable) and the rates on the midstream counters have to be in the range 10-20 Hz (acceptable up to 50 Hz) @50 nA. Counting rates in the range of hundreds of Hz may indicate bad beam tune or bleed-through from other Halls.

• Note 2: At the end of each run, follow the standard DAQ restart sequence

"end run", "cancel", "reset", then if the run ended correctly, "download", "prestart", "iocjscalerRestartAll.sh", "go". If the run did not end correctly or if any ROCs had to be rebooted, "configure", "download", "prestart", "iocjscalerRestartAll.sh", "go".

After each step, make sure it is complete in the Run Control message window. If a ROC has crashed, find which one it is and issue a roc_reboot command and try again. Contact the DAQ expert if there are any questions.

• Note 3: Nominal beam positions: 2C24A (X=0.2 mm, Y=0.4 mm) , 2H01 (X=0.6 mm, Y=0.2 mm)

• Note 4: Do not turn OFF FTOF HVs, even during the beam tune with CW beam (turn off if tuned/pulsed beam in the upstream beamline)

• Note 5: In case of a Torus and/or Solenoid Fast Dump do the following:
  1. Notify MCC to request beam OFF and to drop Hall B status to Power Permit
  2. Call Engineering on-call
  3. Make separate log entry with copies to HBTORUS and HBSOLENOID logbooks. In the "Notify" field add Ruben Fair, Probir Goshal, Dave Kashy and esr-users@jlab.org
  4. Notify Run Coordinator
  5. Turn off all detectors

• Note 6: When beam is being delivered to the Faraday Cup:
  1. the Fast Shut Down elements: Upstream, Midstream, Downstream, BOM, and Solenoid should always be in the state UNMASKED
  2. No changes to the FSD threshold should be made without RC or beamline expert approval

• Note 7: Any request for a special run or change of configuration has to be approved by the RC & documented

• Note 8: Carefully check the BTA every hour and run the script btaGet.py to print for you what HAS TO BE in BTA for this hour. Edit BTA if it is incorrect.

• Note 9: Reset CLAS12MON frequently to avoid histogram saturation.

• Note 10: Shift workers must check the occupancies! Use this tool to compare to previous runs: https://clas12mon.jlab.org/mon12/histograms/

• Note 11 Do not Turn OFF MVT HV: Instead go to 'Restore settings' from the MVT overview screen:
  1. SafeMode.snp for beam tuning and Moeller runs
  2. MV_HV_FullField.snp for full solenoid field
  3. MV_HV_MidField.snp wgeb solenoid < 4T

• NOTE 12 Check the vacuum periodically, make sure vacuum id not higher than 5e-5

• NOTE 13 Always reset the CFD threshold after all power off/on on the CFD crate

After the CAMAC crate 1 holding the CND CFD boards is switched off for any reason, it is mandatory to reset the associated thesholds typing the following command from any clon machine terminal:

>> $CODA/src/rol/Linux_x86_64/bin/cnd_cfd_thresh -w 0

• NOTE 14 Due to instability of the solenoid field measurement, BMT software solenoid interlock is currently bypassed. In case of the solenoid accident, shift operator should put the BMT to the safe mode manually.

Run Plan: (Updated: Oct. 17 2018 at 15:30) Continue production data taking at 45 nA, full target at nominal DAQ setting. If there will be down time >1 hour, no beam, call Domenique +33 616 99 77 72. She needs 30 min to do pedestal measurement for CND Make sure that the FSD thresholds are set correctly and they are unmask when ready to receive beam to the FC Upstream 2000 Midstream 1000 Downstream 675000 BOM 30000 Dwell time 5 ms Shift Worker Notes: If the machine is down for more than 30 min ask for low current first 5 nA ,make sure that the beam is stable both in position and current, check that the rates are OK on all the detectors and halo counters. Then ask for 45 nA and continue data for production. If there are issues with the beam call RC. Sometimes MCC operator may ask to deliver tuned mode beam --- do not accept it. We need CW beam sent to the Faraday cup. If there is indeed a need for tuned beam, it should be sent to the tagger dump with the tagger magnet on. If you are uncertain, please call RC/PDL. For RICH recovery procedures, please see Log entry https://logbooks.jlab.org/entry/3562273. This would apply in the cases of 1. DAQ crash: rich4 is not responding or 2. RICH alarms (LV,missing tile, temperature etc). If it does not work or you are uncertain about what to do, contact the RICH expert on call. In case of other questions or uncertainties of what to do, call the RC

General Instructions: For a given beam current, compute the FSD thresholds according to the Establish Physics Quality Beam document. Call MCC to update the values. Contact the beamline expert if there are questions about setting the FSD thresholds. The main lights in the Hall (dome lights) and the Forward Carriage lights are being kept off because of light leaks affecting some of the detectors. If these lights are switched on during an access, they should be switched off when leaving the Hall. Note that the dome lights when switched off cannot be turned back on immediately because they require 10-15 min to cooldown. Do not run more than 60 minutes above 30 nA with 5-pass beam without the beam blocker in front of Faraday cup. Put beam blocker in for long running at high currents for 5 pass operations. Turn DC HV off only for beam tuning; if no beam is available or when beam is stable, keep them on even if you are not taking data. In case of loss of communication with IOCBTARG, follow instructions at https://logbooks.jlab.org/entry/3502218 With any issue contact On-Call Experts or RC - do not spend more than 15-20 min trying to fix the problem. All jscaler iocs (iocjscalerX) on the health screen (under DAQ tab) must be restarted after every DAQ prestart is completed. Follow this link for detailed instructions https://userweb.jlab.org/~baltzell/CLAS12/SC/jlabScalersOps.txt Check that no unnecessary beamline-related screens are open. This includes particularly the big beamline overview screen, but also and any motor/harp/collimator screens, and ioc health screens. Reference harp scans: 2C21, 2C24, 2H01 Every Shift: Follow run plan as outlined by RC If any concern about beam stability, ask MCC if orbit locks are on (they should be). Keep shift summary up to date in HBLOG. Record all that happens. Check on white board all scalers, strip charts and monitoring plots that need to be logged regularly Document any beam condition change and send scaler GUIs to HBLOG Fill out BTA hourly. Click "Load from EPICS" to automatically fill the left side. When you do BTA keep track of of BANU. Include at the end of shift summary log details of BANU: the reason and duration. Fill and submit the shift checklist in the logbook Every Run: Log screenshots of the following screens, and make sure at the moment you capture the screen the beam is ON main scaler GUI display Detector occupancy plots Trigger rate gui Beam strip charts FTCalo FADC scalers

Webcams Faraday Cup Beam Viewer Tagger Beam Dump Viewer CND/CTOF Ammeter FTOF/ECAL Ammeter Hall Fisheye Saclay Cryotarget

Manuals CED Manual MON12 Manual off-line Manual

Epics on the web Hall B WebOPI (CUE Login) Accelerator (CUE Login)

Fall 2018 Run

Spring 2018 Run

Hall-B Operation Safety Procedures Engineering Run Wiki Engeineering Run Analysis Wiki Run Group A Analysis Wiki RCDB CLAS12 mon page Comparison between mon12 histograms (last 5 runs) Accumulated datasize Run lists RGA Fall 18 run list RGA Winter 18 run list ER run list

Accelerator Accelerator Whiteboard Program Deputy Shift Plans Run Coordinator Reports

Bluejean meetings [1] RGA RC and analysis meetings 7572697303