The HPS Run Wiki

[edit]

• Shift Documentation
• Short Term Schedule
• Long Term Schedule
• Monitoring

Important Phone Numbers Shift Schedule Shift-Taker's Checklist Hot Checkout Beam Time Accounting HPS Run Spreadsheet

Procedures Commissioning Plans: Beamline Beam Trips Trigger (old) ECal SVT SVT TOSP (1,2,3) Tunnel/Hall Access Power Failure

Manuals Harp Scans Beam Trip Runs SVT ECal (Annex) DAQ Beamline Turning Chicane ON/OFF Chicane Settings Slow Controls

JLab Logbooks MCC Hall-A Hall-B Hall-C Hall-D

First rule of HPS: Document all your work in the logbook!

RC: Raphael Dupre

• (757) 575-7540
• 9 575 7540 from Counting Room

PDL: Stepan Stepanyan

Run Plan for April 23-30, 2015: During week days, Mon-Thursday, there will be no Day shifts due to work in the hall. We will be running with 1.05GeV beam. This beam needs to be carefully restored, first to the tagger dump, then to the alcove and Faraday cup screen. See detailed instructions in the right pannel. Short term schedule: Turn ON the ECal and check for normal scalers ([1]) Call SVT expert. Expert will check conditions and turn ON the SVT Only SVT expert should move the SVT! Take data at 40 nA for few hours Check if DAQ runs properly and if all monitors look reasonable on both SVT and ECal (call experts) Log errors for each DAQ crash Use HpsTrigCommV1M1.trg trigger file Take trigger commissioning data runs. See Valery's note on the run Wiki under commissioning trigger. If orbit locks are on, call Rafayel for beam trip study. Take 4 hours of beam trip data with wire up; take 4 hours of beam trip data with wire down. In absence of other requests, take data at 40 nA. Be sure to block Faraday cup if higher current. Miscellaneous Notes: If you change beam current current, turn orbit locks off first, there is a current - position dependence on the stripline BPMs 2H00 and 2H02 Do NOT change magnet currents when beam is on Do not run more than 30 minutes above 50 nA without the beam blocker put beam blocker in for long running at high current

General Instructions: Every Shift: Follow run plan as outlined by RC Ask MCC if orbit locks are on, they should be. Keep shift summary up-to-date in HBLOG. Record all that happens. Check on white board all scalers, strip charts and monitoring plots that need to be logged regularly Document any beam condition change and send scaler GUIs to HBLOG Fill the shift check list for every shifts [2] Update the run table on Google Docs. Perform 2H02A harp scan once per shift or when beam conditions have changed, based on beam monitors (BPMs, halo rates, beam-viewer) With any issue contact On-Call Experts or RC. SVT Instructions Before sending beam to Faraday cup, verify (and page SVT expert if otherwise): SVT should be open: "Position" at 0.000 mm in the main scaler_hps GUI SVT HV is off: all red/green indicators RED in SVT bias GUI The first time sending beam to the Faraday cup after the hall is closed, page the SVT expert. Acceptable Beam Conditions: To establish good beam conditions first send beam to the tagger dump (ask MCC to turn ON the tagger). Check position, it should corresponds to previous good settings [3] Check profile using 2C21 and tagger harp scans, it should correspond to previous settings ([4],[5]) Beam can be accepted at this level if it is within 20% of previous standards Halo counters TAG-L/T/T2 should be ~10Hz/nA [6], While MCC degausses the tagger magnet, turn the chicane ON Strictly follow the procedure in the beam line manual! Before sending beam to the Faraday cup Check 3mm collimator is IN Check HPS target is OUT Check SVT is out (position 0 mm) Send beam to the Faraday cup Tune beam profile with 2H02A harp scan to be wide in X-direction and narrow in Y (see ref [7]) Check the beam spot on chromax viewer The halo counter rates before HPS must be low: UPS-L and UPS-R few Hz/nA, The tagger counters and downstream counters should count <<1 Hz/nA The halo counter rates on HPS, HPS-L/R/T/SC, depends on the collimator and HPS chicane settings, but should not be more than 100 Hz/nA [8] Positions on BPMs must be close to what they were before [9] Contact SVT expert to do SVT Wire Scan Ask MCC to establish HPS orbit locks Ask beam to be turned OFF to insert the 4um W target Before accepting beam, make sure all the previous conditions are met. Always read previous log entries, compare settings of BPMs and correctors with previous settings using scaler_hps GUI.

Long Term Schedule Proposal PowerPoint

Accelerator White Board Schedule Weekly Run Coordinator Reports MCC Daily Meetings HPS Shift Schedule

Run Coordinator March 1 - March 11 Stepan Stepanyan March 12 - March 18 Francios-Xavier Girod March 19 - April 1 John Jaros April 2 - April 8 Nathan Baltzell April 9 - April 15 Takashi Maruyama April 16 - April 22 Maurik Holtrop April 23 - April 29 Raphael Dupre April 30 - May 6 Takashi Maruyama

Physics Division Liaison Stepan Stepanyan

Beamline On-Call Takashi Maruyama May 5 - May 11 Francios-Xavier Girod May 12 - May 19 Stepan Stepanyan DAQ On-Call NOW Sergey Boyarinov

ECAL On-Call March 1 - March 9 Andrea Celentano March 9 - March 23 Nathan Baltzell March 23 - March 30 Holly Vance March 30 - April 13 Gabriel Charles April 13 - April 20 Raphael Dupre April 20 - April 27 Michel Garcon April 27 - May 4 Holly Vance

SVT On-Call March 8 - March 14 Sho Uemura March 15 - March 28 Omar Moreno March 29 - April 4 Pelle Hansson April 5 - April 8 Omar Moreno April 9 - April 19 Matt Graham April 20 - April 26 Tim Nelson April 27 - May 4 Sho Uemura

SlowControls On-Call March 1 - March 18 Hovanes Egiyan March 19 - April 1 Stepan Stepanyan April 22 - April 29 Bryan McKinnon April 30 - May 4 Sho Uemura May 5 - May 19 Nerses Gevorgyan

Webcams: Tagger Beam Dump Viewer Faraday Cup Viewer ECal Chiller Viewer ECal LV Supply Viewer Alcove Viewer

Trigger: 1.1 GeV MC Trigger Distributions #Hits: 0, 1, 2, 3

Accelerator: End Station Status Accelerator Ops 1 Accelerator Ops 2 Accelerator White Board Schedule Slow Controls: HPS MYA Variables Hall B EPICS Database

Online & Offline: Monitoring Gui Run Spreadsheet HPS Data Catalog Jenkins / Nexus Shift Docs @ GitHub