Difference between revisions of "DR dipole (15 deg)"

From Ciswikidb
Jump to: navigation, search
Line 33: Line 33:
 
* Riad's analysis of the two dipoles - [[media:Dipole15deg_FieldMap.pptx]]
 
* Riad's analysis of the two dipoles - [[media:Dipole15deg_FieldMap.pptx]]
  
; January 13 2021 - MMF coil measurements
+
(January 13 2021 - MMF coil measurements)
  
From: Mike Beck <jbeck@jlab.org>
+
;Magnet DR01
Sent: Wednesday, January 13, 2021 9:22 AM
+
TOP-SN#01
To: Joseph Meyers
+
L/60Hz=1.617mH
Cc: Joe Grames; Jay Benesch; Riad Suleiman
+
DCR=915.9 milliohm
Subject: Inductance/DCR DR 15* dipoles
+
BOTTOM-SN#02
Measured Inductance and DCR values for the DR 15* dipoles in half's.
+
L/60Hz=1.563mH
 +
DCR=887.1 milliohm
  
Magnet DR01
+
; Magnet DR02
TOP-SN#01
+
TOP-SN#03
L/60Hz=1.617mH
+
L/60Hz=1.527mH
DCR=915.9 milliohm
+
DCR=881.5 milliohm  
BOTTOM-SN#02
+
BOTTOM-SN#04
L/60Hz=1.563mH
+
L/60Hz=1.540mH
DCR=887.1 milliohm
+
DCR=887.3 milliohm
  
Magnet DR02
+
From Jay - The ratio of inductances suggests a 1.7% turns discrepancy while resistance suggests 3.2% top vs bottom in DR01.  (inductance goes as N^2, resistance as N).  I suggest using the DR02 in the machine.
TOP-SN#03
+
L/60Hz=1.527mH
+
DCR=881.5 milliohm
+
BOTTOM-SN#04
+
L/60Hz=1.540mH
+
DCR=887.3 milliohm
+
 
+
From Jay - The ratio of inductances suggests a 1.7% turns discrepancy while resistance suggests 3.2% top vs bottom in DR01.  (inductance goes as N^2, resistance as N).  I suggest using the DR02 in the machine.
+

Revision as of 14:26, 14 June 2021

A new 15 deg bend magnet was designed to operate at higher beam energy and to minimize higher order multipoles.

Design

- Dipole fixture media:200KeVYDipoleFixture-JL0087295.pdf
- Dipole winding media:200KeVYDipoleCoil-JL0087835.pdf
  • Shims
- media:MDR_shim.pdf
- Laminate shim stock (2 mil * 31 layers = 0.064 mil thick laminate)
- 28 mil shim for 1.688 deg (top 0.844 deg cw, bottom 0.844 deg ccw); each 2 mil laer changes angle 0.048 deg

Fabrication

Milhous was awarded fabrication of two DR magnets (four halves).
  • Oct 5, 2020 - First half received from Milhous last weeks
  • Mike's report ... The dimension inspection of the aluminum coil fixture is correct. Electrical testing, hipot and surge testing at 500V is completed, all meet JLAB acceptance criteria. Can not confirm turn count is correct with this kind of winding process and there is no additional coil to conduct coil comparison testing. It might be reasonable to assume the wire count is correct as we only have one halve section and no mapping can occur until we receive the next halve. Coil appearance looks reasonable for the fashion used for fabrication/winding. We just need 3 more halve sections to put these magnets together, after QA is completed on the additional 3 articles we will begin mapping. Milhous winding another half, will shop to JLab ASAP, within a week or so
Specifications and markup documents

Oct 23, 2019 - Jay mark-up for low- and high- energy coil

Archive of intermediate drawings

Oct 18, 2019 - Final 15 deg coil fixture

Measurments

(January 13 2021 - MMF coil measurements)

Magnet DR01

TOP-SN#01 L/60Hz=1.617mH DCR=915.9 milliohm BOTTOM-SN#02 L/60Hz=1.563mH DCR=887.1 milliohm

Magnet DR02

TOP-SN#03 L/60Hz=1.527mH DCR=881.5 milliohm BOTTOM-SN#04 L/60Hz=1.540mH DCR=887.3 milliohm

From Jay - The ratio of inductances suggests a 1.7% turns discrepancy while resistance suggests 3.2% top vs bottom in DR01. (inductance goes as N^2, resistance as N). I suggest using the DR02 in the machine.